Add the first axi_ethernet driver for little-endian Microblaze.
Signed-off-by: Michal Simek monstr@monstr.eu
--- v2: - Fix return addreses - Fix NULL pointer defer for priv structure
v3: - Freeing allocated memory when initialization failed --- .../xilinx/microblaze-generic/microblaze-generic.c | 4 + drivers/net/Makefile | 1 + drivers/net/xilinx_axi_emac.c | 537 ++++++++++++++++++++ include/configs/microblaze-generic.h | 3 + 4 files changed, 545 insertions(+), 0 deletions(-) create mode 100644 drivers/net/xilinx_axi_emac.c
diff --git a/board/xilinx/microblaze-generic/microblaze-generic.c b/board/xilinx/microblaze-generic/microblaze-generic.c index 5c07fdb..e711546 100644 --- a/board/xilinx/microblaze-generic/microblaze-generic.c +++ b/board/xilinx/microblaze-generic/microblaze-generic.c @@ -73,6 +73,10 @@ int board_eth_init(bd_t *bis) { int ret = 0;
+#ifdef CONFIG_XILINX_AXIEMAC + ret |= xilinx_axiemac_initialize(bis, XILINX_AXIEMAC_BASEADDR, + XILINX_AXIDMA_BASEADDR); +#endif #ifdef CONFIG_XILINX_EMACLITE ret |= xilinx_emaclite_initialize(bis, XILINX_EMACLITE_BASEADDR); #endif diff --git a/drivers/net/Makefile b/drivers/net/Makefile index fd9d0b4..01752a5 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -83,6 +83,7 @@ COBJS-$(CONFIG_TSEC_ENET) += tsec.o COBJS-$(CONFIG_TSI108_ETH) += tsi108_eth.o COBJS-$(CONFIG_ULI526X) += uli526x.o COBJS-$(CONFIG_VSC7385_ENET) += vsc7385.o +COBJS-$(CONFIG_XILINX_AXIEMAC) += xilinx_axi_emac.o COBJS-$(CONFIG_XILINX_EMACLITE) += xilinx_emaclite.o
COBJS := $(sort $(COBJS-y)) diff --git a/drivers/net/xilinx_axi_emac.c b/drivers/net/xilinx_axi_emac.c new file mode 100644 index 0000000..3c25381 --- /dev/null +++ b/drivers/net/xilinx_axi_emac.c @@ -0,0 +1,537 @@ +/* + * Copyright (C) 2011 Michal Simek monstr@monstr.eu + * Copyright (C) 2011 PetaLogix + * Copyright (C) 2010 Xilinx, Inc. All rights reserved. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <config.h> +#include <common.h> +#include <net.h> +#include <malloc.h> +#include <asm/io.h> + +/* Axi Ethernet registers offset */ +#define XAE_IS_OFFSET 0x0000000C /* Interrupt status */ +#define XAE_IE_OFFSET 0x00000014 /* Interrupt enable */ +#define XAE_RCW1_OFFSET 0x00000404 /* Rx Configuration Word 1 */ +#define XAE_TC_OFFSET 0x00000408 /* Tx Configuration */ +#define XAE_EMMC_OFFSET 0x00000410 /* EMAC mode configuration */ +#define XAE_MDIO_MC_OFFSET 0x00000500 /* MII Management Config */ +#define XAE_MDIO_MCR_OFFSET 0x00000504 /* MII Management Control */ +#define XAE_MDIO_MRD_OFFSET 0x0000050C /* MII Management Read Data */ + +/* Link setup */ +#define XAE_EMMC_LINKSPEED_MASK 0xC0000000 /* Link speed */ +#define XAE_EMMC_LINKSPD_10 0x00000000 /* Link Speed mask for 10 Mbit */ +#define XAE_EMMC_LINKSPD_100 0x40000000 /* Link Speed mask for 100 Mbit */ +#define XAE_EMMC_LINKSPD_1000 0x80000000 /* Link Speed mask for 1000 Mbit */ + +/* Interrupt Status/Enable/Mask Registers bit definitions */ +#define XAE_INT_RXRJECT_MASK 0x00000008 /* Rx frame rejected */ +#define XAE_INT_MGTRDY_MASK 0x00000080 /* MGT clock Lock */ + +/* Receive Configuration Word 1 (RCW1) Register bit definitions */ +#define XAE_RCW1_RX_MASK 0x10000000 /* Receiver enable */ + +/* Transmitter Configuration (TC) Register bit definitions */ +#define XAE_TC_TX_MASK 0x10000000 /* Transmitter enable */ + +/* + * Station address bits [47:32] + * Station address bits [31:0] are stored in register UAW0 + */ +#define XAE_UAW0_OFFSET 0x00000700 /* Unicast address word 0 */ +#define XAE_UAW1_OFFSET 0x00000704 /* Unicast address word 1 */ +#define XAE_UAW1_UNICASTADDR_MASK 0x0000FFFF + +/* MDIO Management Configuration (MC) Register bit definitions */ +#define XAE_MDIO_MC_MDIOEN_MASK 0x00000040 /* MII management enable*/ + +/* MDIO Management Control Register (MCR) Register bit definitions */ +#define XAE_MDIO_MCR_PHYAD_MASK 0x1F000000 /* Phy Address Mask */ +#define XAE_MDIO_MCR_PHYAD_SHIFT 24 /* Phy Address Shift */ +#define XAE_MDIO_MCR_REGAD_MASK 0x001F0000 /* Reg Address Mask */ +#define XAE_MDIO_MCR_REGAD_SHIFT 16 /* Reg Address Shift */ +#define XAE_MDIO_MCR_OP_READ_MASK 0x00008000 /* Op Code Read Mask */ +#define XAE_MDIO_MCR_OP_WRITE_MASK 0x00004000 /* Op Code Write Mask */ +#define XAE_MDIO_MCR_INITIATE_MASK 0x00000800 /* Ready Mask */ +#define XAE_MDIO_MCR_READY_MASK 0x00000080 /* Ready Mask */ + +#define XAE_MDIO_DIV_DFT 29 /* Default MDIO clock divisor */ + +/* DMA macros */ +/* Bitmasks of XAXIDMA_CR_OFFSET register */ +#define XAXIDMA_CR_RUNSTOP_MASK 0x00000001 /* Start/stop DMA channel */ +#define XAXIDMA_CR_RESET_MASK 0x00000004 /* Reset DMA engine */ + +/* Bitmasks of XAXIDMA_SR_OFFSET register */ +#define XAXIDMA_HALTED_MASK 0x00000001 /* DMA channel halted */ + +/* Bitmask for interrupts */ +#define XAXIDMA_IRQ_IOC_MASK 0x00001000 /* Completion intr */ +#define XAXIDMA_IRQ_DELAY_MASK 0x00002000 /* Delay interrupt */ +#define XAXIDMA_IRQ_ALL_MASK 0x00007000 /* All interrupts */ + +/* Bitmasks of XAXIDMA_BD_CTRL_OFFSET register */ +#define XAXIDMA_BD_CTRL_TXSOF_MASK 0x08000000 /* First tx packet */ +#define XAXIDMA_BD_CTRL_TXEOF_MASK 0x04000000 /* Last tx packet */ + + +#define ENET_MAX_MTU PKTSIZE_ALIGN +#define DMAALIGN 128 + +static u8 RxFrame[ENET_MAX_MTU] __attribute((aligned(DMAALIGN))) ; + +/* reflect dma offsets */ +struct axidma_reg { + u32 control; /* DMACR */ + u32 status; /* DMASR */ + u32 current; /* CURDESC */ + u32 reserved; + u32 tail; /* TAILDESC */ +}; + +/* Private driver structures */ +struct axidma_priv { + struct axidma_reg *dmatx; + struct axidma_reg *dmarx; +}; + +/* BD descriptors */ +typedef struct axidma_bd { + u32 next; /* Next descriptor pointer */ + u32 reserved1; + u32 phys; /* Buffer address */ + u32 reserved2; + u32 reserved3; + u32 reserved4; + u32 cntrl; /* Control */ + u32 status; /* Status */ + u32 app0; + u32 app1; /* TX start << 16 | insert */ + u32 app2; /* TX csum seed */ + u32 app3; + u32 app4; + u32 sw_id_offset; + u32 reserved5; + u32 reserved6; +} axidma_bd __attribute((aligned(DMAALIGN))); + +/* Static BDs - driver uses only one BD */ +static axidma_bd tx_bd; +static axidma_bd rx_bd; + +/* Use MII register 1 (MII status register) to detect PHY */ +#define PHY_DETECT_REG 1 + +/* Mask used to verify certain PHY features (or register contents) + * in the register above: + * 0x1000: 10Mbps full duplex support + * 0x0800: 10Mbps half duplex support + * 0x0008: Auto-negotiation support + */ +#define PHY_DETECT_MASK 0x1808 + +static u16 phy_read(struct eth_device *dev, u32 PhyAddress, u32 RegisterNum) +{ + u32 MdioCtrlReg = 0; + + /* Wait till MDIO interface is ready to accept a new transaction. */ + while (!(in_be32(dev->iobase + XAE_MDIO_MCR_OFFSET) + & XAE_MDIO_MCR_READY_MASK)) + ; + + MdioCtrlReg = ((PhyAddress << XAE_MDIO_MCR_PHYAD_SHIFT) & + XAE_MDIO_MCR_PHYAD_MASK) | + ((RegisterNum << XAE_MDIO_MCR_REGAD_SHIFT) + & XAE_MDIO_MCR_REGAD_MASK) | + XAE_MDIO_MCR_INITIATE_MASK | + XAE_MDIO_MCR_OP_READ_MASK; + + out_be32(dev->iobase + XAE_MDIO_MCR_OFFSET, MdioCtrlReg); + + /* Wait till MDIO transaction is completed. */ + while (!(in_be32(dev->iobase + XAE_MDIO_MCR_OFFSET) + & XAE_MDIO_MCR_READY_MASK)) + ; + + /* Read data */ + return (u16) in_be32(dev->iobase + XAE_MDIO_MRD_OFFSET); +} + +/* setting axi emac and phy to proper setting */ +static void setup_phy(struct eth_device *dev) +{ + int i; + unsigned retries = 100; + u16 PhyReg; + u16 PhyReg2; + int PhyAddr = -1; + u32 emmc_reg; + + debug("detecting phy address\n"); + + /* detect the PHY address */ + for (PhyAddr = 31; PhyAddr >= 0; PhyAddr--) { + PhyReg = phy_read(dev, PhyAddr, PHY_DETECT_REG); + + if ((PhyReg != 0xFFFF) && + ((PhyReg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) { + /* Found a valid PHY address */ + + debug("Found valid phy address, %d\n", PhyReg); + break; + } + } + + debug("waiting for the phy to be up\n"); + + /* wait for link up and autonegotiation completed */ + while (retries-- > 0) { + if ((PhyReg & 0x24) == 0x24) + break; + } + + /* get PHY id */ + PhyReg = phy_read(dev, PhyAddr, 2); + PhyReg2 = phy_read(dev, PhyAddr, 2); + i = (PhyReg << 16) | PhyReg2; + debug("LL_TEMAC: Phy ID 0x%x\n", i); + + /* Marwell 88e1111 id - ml50x, 0x1410141 id - sp605 */ + if ((i == 0x1410cc2) || (i == 0x1410141)) { + debug("Marvell PHY recognized\n"); + + /* Setup the emac for the phy speed */ + emmc_reg = in_be32(dev->iobase + XAE_EMMC_OFFSET); + emmc_reg &= ~XAE_EMMC_LINKSPEED_MASK; + + PhyReg = phy_read(dev, PhyAddr, 17); + + if ((PhyReg & 0x8000) == 0x8000) { + emmc_reg |= XAE_EMMC_LINKSPD_1000; + printf("1000BASE-T\n"); + } else if ((PhyReg & 0x4000) == 0x4000) { + printf("100BASE-T\n"); + emmc_reg |= XAE_EMMC_LINKSPD_100; + } else { + printf("10BASE-T\n"); + emmc_reg |= XAE_EMMC_LINKSPD_10; + } + + /* Write new speed setting out to Axi Ethernet */ + out_be32(dev->iobase + XAE_EMMC_OFFSET, emmc_reg); + + /* + * Setting the operating speed of the MAC needs a delay. There + * doesn't seem to be register to poll, so please consider this + * during your application design. + */ + udelay(1); + } +} + +/* STOP DMA transfers */ +static void axiemac_halt(struct eth_device *dev) +{ + struct axidma_priv *dma = dev->priv; + + if (dev->state) { + /* Stop the hardware */ + dma->dmatx->control &= ~XAXIDMA_CR_RUNSTOP_MASK; + dma->dmarx->control &= ~XAXIDMA_CR_RUNSTOP_MASK; + dev->state = 0; + } + debug("axiemac halted\n"); +} + +static void axi_ethernet_init(struct eth_device *dev) +{ + /* + * Check the status of the MgtRdy bit in the interrupt status + * registers. This must be done to allow the MGT clock to become stable + * for the Sgmii and 1000BaseX PHY interfaces. No other register reads + * will be valid until this bit is valid. + * The bit is always a 1 for all other PHY interfaces. + */ + u32 timeout = 200; + while (timeout && + (!(in_be32(dev->iobase + XAE_IS_OFFSET) & XAE_INT_MGTRDY_MASK))) + timeout--; + + if (!timeout) + printf("%s: Timeout\n", __func__); + + /* Stop the device and reset HW */ + /* Disable interrupts */ + out_be32(dev->iobase + XAE_IE_OFFSET, 0); + + /* Disable the receiver */ + out_be32(dev->iobase + XAE_RCW1_OFFSET, + in_be32(dev->iobase + XAE_RCW1_OFFSET) & ~XAE_RCW1_RX_MASK); + + /* + * Stopping the receiver in mid-packet causes a dropped packet + * indication from HW. Clear it. + */ + /* set the interrupt status register to clear the interrupt */ + out_be32(dev->iobase + XAE_IS_OFFSET, XAE_INT_RXRJECT_MASK); + + /* Setup HW */ + /* Set default MDIO divisor */ + out_be32(dev->iobase + XAE_MDIO_MC_OFFSET, + (u32) XAE_MDIO_DIV_DFT | XAE_MDIO_MC_MDIOEN_MASK); + + debug("XAxiEthernet InitHw: done\n"); +} + +/* DO NOT called setup mac without proper hw initialization */ +static void setup_mac(struct eth_device *dev) +{ + /* Set the MAC address */ + int val = ((dev->enetaddr[3] << 24) | (dev->enetaddr[2] << 16) | + (dev->enetaddr[1] << 8) | (dev->enetaddr[0])); + out_be32(dev->iobase + XAE_UAW0_OFFSET, val); + + val = (dev->enetaddr[5] << 8) | dev->enetaddr[4] ; + val |= in_be32(dev->iobase + XAE_UAW1_OFFSET) + & ~XAE_UAW1_UNICASTADDR_MASK; + out_be32(dev->iobase + XAE_UAW1_OFFSET, val); +} + +/* Reset DMA engine */ +static void axi_dma_init(struct eth_device *dev) +{ + struct axidma_priv *dma = dev->priv; + + /* Reset the engine so the hardware starts from a known state */ + dma->dmatx->control = XAXIDMA_CR_RESET_MASK; + dma->dmarx->control = XAXIDMA_CR_RESET_MASK; + + /* At the initialization time, hardware should finish reset quickly */ + u32 timeout = 500; + while (timeout--) { + /* Check transmit/receive channel */ + /* Reset is done when the reset bit is low */ + if (!(dma->dmatx->control | dma->dmarx->control) + & XAXIDMA_CR_RESET_MASK) + break; + timeout -= 1; + } + + if (!timeout) + printf("%s: Timeout\n", __func__); +} + +static int axiemac_init(struct eth_device *dev, bd_t * bis) +{ + struct axidma_priv *dma = dev->priv; + debug("axi emac init started\n"); + + /* + * Initialize AXIDMA engine. AXIDMA engine must be initialized before + * AxiEthernet. During AXIDMA engine initialization, AXIDMA hardware is + * reset, and since AXIDMA reset line is connected to AxiEthernet, this + * would ensure a reset of AxiEthernet. + */ + axi_dma_init(dev); + + /* Initialize AxiEthernet hardware. */ + axi_ethernet_init(dev); + + /* setup mac must be called when hw is initialized */ + setup_mac(dev); + + /* Start the hardware */ + dma->dmarx->control |= XAXIDMA_CR_RUNSTOP_MASK; + /* Start DMA RX channel. Now it's ready to receive data.*/ + dma->dmarx->current = (u32)&rx_bd; + + /* Disable all RX interrupts before RxBD space setup */ + dma->dmarx->control &= ~(XAXIDMA_IRQ_ALL_MASK & XAXIDMA_IRQ_ALL_MASK); + + /* Setup the BD. */ + memset((void *) &rx_bd, 0, sizeof(axidma_bd)); + rx_bd.next = (u32)&rx_bd; + rx_bd.phys = (u32)&RxFrame; + rx_bd.cntrl = sizeof(RxFrame); + /* Flush the last BD so DMA core could see the updates */ + flush_cache((u32)&rx_bd, sizeof(axidma_bd)); + + /* it is necessary to flush RxFrame because if you don't do it + * then cache can contain uninitialized data */ + flush_cache((u32)&RxFrame, sizeof(RxFrame)); + + /* Rx BD is ready - start */ + dma->dmarx->tail = (u32)&rx_bd; + + /* enable TX */ + out_be32(dev->iobase + XAE_TC_OFFSET, XAE_TC_TX_MASK); + /* enable RX */ + out_be32(dev->iobase + XAE_RCW1_OFFSET, XAE_RCW1_RX_MASK); + + /* PHY setup */ + setup_phy(dev); + dev->state = 1; + debug("axi emac init complete\n"); + return 0; +} + +static int axiemac_send(struct eth_device *dev, volatile void *ptr, int len) +{ + struct axidma_priv *dma = dev->priv; + + if (len > ENET_MAX_MTU) + len = ENET_MAX_MTU; + + /* Flush packet to main memory to be trasfered by DMA */ + flush_cache(ptr, len); + + /* Setup Tx BD */ + memset((void *) &tx_bd, 0, sizeof(axidma_bd)); + /* At the end of the ring, link the last BD back to the top */ + tx_bd.next = (u32)&tx_bd; + tx_bd.phys = (u32)ptr; + /* save len */ + tx_bd.cntrl = len | XAXIDMA_BD_CTRL_TXSOF_MASK | + XAXIDMA_BD_CTRL_TXEOF_MASK; + + /* Flush the last BD so DMA core could see the updates */ + flush_cache((u32)&tx_bd, sizeof(axidma_bd)); + + if (dma->dmatx->status & XAXIDMA_HALTED_MASK) { + dma->dmatx->current = (u32)&tx_bd; + /* Start the hardware */ + dma->dmatx->control |= XAXIDMA_CR_RUNSTOP_MASK; + } + + /* start transfer */ + dma->dmatx->tail = (u32)&tx_bd; + + /* Wait for transmission to complete */ + debug("axi emac, waiting for tx to be done\n"); + while (!dma->dmatx->status & + (XAXIDMA_IRQ_DELAY_MASK | XAXIDMA_IRQ_IOC_MASK)) + ; + + debug("axi emac send complete\n"); + return 0; +} + +static int IsRxReady(struct eth_device *dev) +{ + u32 status; + struct axidma_priv *dma = dev->priv; + + /* Read pending interrupts */ + status = dma->dmarx->status; + + /* Acknowledge pending interrupts */ + dma->dmarx->status &= XAXIDMA_IRQ_ALL_MASK; + + /* + * If Reception done interrupt is asserted, call RX call back function + * to handle the processed BDs and then raise the according flag. + */ + if ((status & (XAXIDMA_IRQ_DELAY_MASK | XAXIDMA_IRQ_IOC_MASK))) + return 1; + + return 0; +} + +static int axiemac_recv(struct eth_device *dev) +{ + u32 length; + struct axidma_priv *dma = dev->priv; + + /* wait for an incoming packet */ + if (!IsRxReady(dev)) + return 0; + + debug("axi emac, rx data ready\n"); + + /* Disable IRQ for a moment till packet is handled */ + dma->dmarx->control &= ~(XAXIDMA_IRQ_ALL_MASK & XAXIDMA_IRQ_ALL_MASK); + + length = rx_bd.app4 & 0x0000FFFF; +#ifdef DEBUG + print_buffer(&RxFrame, &RxFrame[0], 1, length, 16); +#endif + /* pass the received frame up for processing */ + if (length) + NetReceive(RxFrame, length); + +#ifdef DEBUG + /* It is useful to clear buffer to be sure that it is consistent */ + memset(RxFrame, 0, sizeof(RxFrame)); +#endif + /* Setup RxBD */ + /* Clear the whole buffer and setup it again - all flags are cleared */ + memset((void *) &rx_bd, 0, sizeof(axidma_bd)); + rx_bd.next = (u32)&rx_bd; + rx_bd.phys = (u32)&RxFrame; + rx_bd.cntrl = sizeof(RxFrame); + + /* write bd to HW */ + flush_cache((u32)&rx_bd, sizeof(axidma_bd)); + + /* it is necessary to flush RxFrame because if you don't do it + * then cache will contain previous packet */ + flush_cache((u32)&RxFrame, sizeof(RxFrame)); + + /* Rx BD is ready - start again */ + dma->dmarx->tail = (u32)&rx_bd; + + debug("axi emac rx complete, framelength = %d\n", length); + + return length; +} + +int xilinx_axiemac_initialize(bd_t *bis, int base_addr, int dma_addr) +{ + struct eth_device *dev; + struct axidma_priv *dma; + + dev = calloc(1, sizeof(struct eth_device)); + if (dev == NULL) + return -1; + + dev->priv = calloc(1, sizeof(struct axidma_priv)); + if (dev->priv == NULL) { + free(dev); + return -1; + } + + sprintf(dev->name, "Xilinx_AxiEmac"); + + dev->iobase = base_addr; + dma = dev->priv; + dma->dmatx = dma_addr; + dma->dmarx = (u32)dma->dmatx + 0x30; /* rx channel offset */ + dev->init = axiemac_init; + dev->halt = axiemac_halt; + dev->send = axiemac_send; + dev->recv = axiemac_recv; + + eth_register(dev); + + return 1; +} diff --git a/include/configs/microblaze-generic.h b/include/configs/microblaze-generic.h index a334110..47bfb86 100644 --- a/include/configs/microblaze-generic.h +++ b/include/configs/microblaze-generic.h @@ -67,6 +67,9 @@ #elif XILINX_LLTEMAC_BASEADDR # define CONFIG_XILINX_LL_TEMAC 1 # define CONFIG_SYS_ENET +#elif defined(XILINX_AXIEMAC_BASEADDR) +# define CONFIG_XILINX_AXIEMAC 1 +# define CONFIG_SYS_ENET #endif
#undef ET_DEBUG