This series brings support for HS200 and UHS modes to the mmc core. It has been tested with the hsmmc driver on several platforms (DRA7, AM57x, AM437x, beaglebone black, Atmel SAMA5D3 xplained). Some modifications are required in the host driver to take advantage of this (voltage switching, tuning). The changes to the host driver will be posted a another series as this one is already long enough.
The series starts with a small refactoring of th sd/mmc startup. The first 5 commits are mostly moving code around with little or no functionnal change.
Then the notion of "mode" is introduced. Until now, this information wasn't kept in struct mmc. Only the clock and a flag for ddr was kept. Later the mode information will be used to select the clock frequency, the ddr flag and the tuning procedure. It will be also be check against the host capabilities.
Then comes the big refactoring job in: "mmc: refactor MMC startup to make it easier to support new modes" and "mmc: refactor SD startup to make it easier to support new modes" Since the number of modes is increasing, it makes sense to try them in a more organized way. those commits use a list of supported modes and iterate through them to find the best working one. It also allows to switch more easilly from one mode to another (switching from HS200 to DDR52 to access boot partitions for example)
Then there are a couple of new callback added to: - send the initialization stream (74 clock cycles) - wait while the card is busy (used during UHS voltage switching). checking is done on dat0. - select the IO voltage
Then Power cycle is added. Without power cycle, if a UHS card fails to enumerate in UHS mode, it can't fall back to high speed mode and card enumeration will fail. Also in case of a reset (as opposed to a power on), it ensures that the SDCard is in clean state before re-doing the initialization.
And finally the last commits add the support for HS200 and UHS.
With this in place and the required changes in the HSMMC host driver (including DMA), we observe significant improvements in the performances on a DRA72 evm: eMMC HS200: 124 MB/s eMMC DDR52: 78 MB/s sd SDR104: 71 MB/s sd SDR50: 44 MB/s
cheers,
Jean-Jacques
changes since v1: Changes take in account all the comment made during the first round of review. But it also include a rework of the handling of the voltage supplies and 2 new helper functions that can be used by the host driver during tuning and dts parsing.
Here is a detailed list: * rebase on u-boot/master. * add the description for the new functions/members * fix the typos found in the reviews * limit the new features to DM_MMC only * fix the new checkpatch warnings/errors (is it now more strict ?) * get the voltage regulators from dts (main and IO-lines) * remove the set_vdd callback and do the job in the mmc core * add a send_init_stream callback to perform the 74 clock cycle sequence after power up * do a full power cycle (if possible) before the initialization. This ensures that the sd/MMC is in valid knwon state. Also it allows to check if the power cycling works as expected. * disable the UHS modes is power cycling is not available/working. This ensures that we won't be stuck if the UHS initialization fails. * select the appropriate signal voltage when selecting a mode (MMC only) * add a helper function to parse the generic dt bindings * add a helper function to send the tuning command
Jean-Jacques Hiblot (17): mmc: dm: get the IO-line and main voltage regulators from the dts mmc: split mmc_startup() mmc: move the MMC startup for version above v4.0 in a separate function mmc: make ext_csd part of struct mmc mmc: add a function to read and test the ext csd (mmc >= 4) mmc: introduce mmc modes mmc: Add a function to dump the mmc capabilities mmc: use mmc modes to select the correct bus speed cmd: mmc: display the mode name and current bus speed in the mmc info mmc: refactor SD startup to make it easier to support new modes mmc: refactor MMC startup to make it easier to support new modes mmc: Add a new callback function to perform the 74 clocks cycle sequence mmc: Add support for UHS modes mmc: disable UHS modes if Vcc cannot be switched on and off mmc: Change mode when switching to a boot partition mmc: use the right voltage level for MMC DDR and HS200 modes mmc: add a library function to send tuning command
Kishon Vijay Abraham I (9): mmc: make mmc_set_ios() return status mmc: Enable signal voltage to be selected from mmc core mmc: add power cyle support in mmc core mmc: add a new mmc parameter to disable mmc clock mmc: disable the mmc clock during power off mmc: Add a execute_tuning() callback to the mmc operations. mmc: add HS200 support in MMC core mmc: Retry some MMC cmds on failure dm: mmc: Add a library function to parse generic dt binding
cmd/mmc.c | 3 +- drivers/mmc/Kconfig | 23 + drivers/mmc/fsl_esdhc.c | 2 +- drivers/mmc/mmc-uclass.c | 87 +++ drivers/mmc/mmc.c | 1511 ++++++++++++++++++++++++++++++++++------------ include/mmc.h | 176 +++++- 6 files changed, 1417 insertions(+), 385 deletions(-)