So far we have a convoluted #ifdef mesh that guards the early AXP PMIC setup in board.c. That combination of &&, || and negations is very hard to read, maintain and especially to extend.
Fortunately we have those same conditions already modelled in the Kconfig file, so they are actually redundant. On top of that the real reason we have those preprocessor guards in the first place is about the symbols that are *conditionally* defined: without #ifdefs the build would break because of them being undefined for many boards.
To simplify this, just change the guards to actually look at the symbols needed, so CONFIG_AXP_xxx_VOLT instead of CONFIG_AXPyyy_POWER. This drastically improves the readability of this code, and makes adding PMIC support a pure Kconfig matter.
Signed-off-by: Andre Przywara andre.przywara@arm.com --- board/sunxi/board.c | 32 ++++++++++++++------------------ drivers/power/Kconfig | 2 +- 2 files changed, 15 insertions(+), 19 deletions(-)
diff --git a/board/sunxi/board.c b/board/sunxi/board.c index ebaa9431984..65d79a02c25 100644 --- a/board/sunxi/board.c +++ b/board/sunxi/board.c @@ -597,50 +597,46 @@ void sunxi_board_init(void) } }
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \ - defined CONFIG_AXP818_POWER +#ifdef CONFIG_AXP_DCDC1_VOLT power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT); + power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT); #endif -#if !defined(CONFIG_AXP305_POWER) +#ifdef CONFIG_AXP_DCDC2_VOLT power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT); power_failed |= axp_set_dcdc3(CONFIG_AXP_DCDC3_VOLT); #endif -#if !defined(CONFIG_AXP209_POWER) && !defined(CONFIG_AXP818_POWER) +#ifdef CONFIG_AXP_DCDC4_VOLT power_failed |= axp_set_dcdc4(CONFIG_AXP_DCDC4_VOLT); #endif -#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \ - defined CONFIG_AXP818_POWER - power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT); -#endif
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \ - defined CONFIG_AXP818_POWER +#ifdef CONFIG_AXP_ALDO1_VOLT power_failed |= axp_set_aldo1(CONFIG_AXP_ALDO1_VOLT); #endif -#if !defined(CONFIG_AXP305_POWER) +#ifdef CONFIG_AXP_ALDO2_VOLT power_failed |= axp_set_aldo2(CONFIG_AXP_ALDO2_VOLT); #endif -#if !defined(CONFIG_AXP152_POWER) && !defined(CONFIG_AXP305_POWER) +#ifdef CONFIG_AXP_ALDO3_VOLT power_failed |= axp_set_aldo3(CONFIG_AXP_ALDO3_VOLT); #endif -#ifdef CONFIG_AXP209_POWER +#ifdef CONFIG_AXP_ALDO4_VOLT power_failed |= axp_set_aldo4(CONFIG_AXP_ALDO4_VOLT); #endif
-#if defined(CONFIG_AXP221_POWER) || defined(CONFIG_AXP809_POWER) || \ - defined(CONFIG_AXP818_POWER) +#ifdef CONFIG_AXP_DLDO1_VOLT power_failed |= axp_set_dldo(1, CONFIG_AXP_DLDO1_VOLT); power_failed |= axp_set_dldo(2, CONFIG_AXP_DLDO2_VOLT); -#if !defined CONFIG_AXP809_POWER +#endif +#ifdef CONFIG_AXP_DLDO3_VOLT power_failed |= axp_set_dldo(3, CONFIG_AXP_DLDO3_VOLT); power_failed |= axp_set_dldo(4, CONFIG_AXP_DLDO4_VOLT); #endif +#ifdef CONFIG_AXP_ELDO1_VOLT power_failed |= axp_set_eldo(1, CONFIG_AXP_ELDO1_VOLT); power_failed |= axp_set_eldo(2, CONFIG_AXP_ELDO2_VOLT); power_failed |= axp_set_eldo(3, CONFIG_AXP_ELDO3_VOLT); #endif
-#ifdef CONFIG_AXP818_POWER +#ifdef CONFIG_AXP_FLDO1_VOLT power_failed |= axp_set_fldo(1, CONFIG_AXP_FLDO1_VOLT); power_failed |= axp_set_fldo(2, CONFIG_AXP_FLDO2_VOLT); power_failed |= axp_set_fldo(3, CONFIG_AXP_FLDO3_VOLT); @@ -649,7 +645,7 @@ void sunxi_board_init(void) #if defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER power_failed |= axp_set_sw(IS_ENABLED(CONFIG_AXP_SW_ON)); #endif -#endif +#endif /* CONFIG_AXPxxx_POWER */ printf("DRAM:"); gd->ram_size = sunxi_dram_init(); printf(" %d MiB\n", (int)(gd->ram_size >> 20)); diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index 7f3b990d231..83cb31c937a 100644 --- a/drivers/power/Kconfig +++ b/drivers/power/Kconfig @@ -180,7 +180,7 @@ config AXP_DCDC3_VOLT
config AXP_DCDC4_VOLT int "axp pmic dcdc4 voltage" - depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER || AXP305_POWER + depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP305_POWER default 1250 if AXP152_POWER default 1200 if MACH_SUN6I default 0 if MACH_SUN8I