When diffing through the various kwbimage.cfg files only show relevant changes.
Signed-off-by: Luka Perkov luka@openwrt.org CC: Prafulla Wadaskar prafulla@marvell.com CC: Stefan Roese sr@denx.de --- board/iomega/iconnect/kwbimage.cfg | 4 ++-- board/raidsonic/ib62x0/kwbimage.cfg | 22 +++++++++++----------- 2 files changed, 13 insertions(+), 13 deletions(-)
diff --git a/board/iomega/iconnect/kwbimage.cfg b/board/iomega/iconnect/kwbimage.cfg index 3c63a03..f4260fa 100644 --- a/board/iomega/iconnect/kwbimage.cfg +++ b/board/iomega/iconnect/kwbimage.cfg @@ -20,7 +20,7 @@ NAND_PAGE_SIZE 0x0800 # Configure RGMII-0 interface pad voltage to 1.8V DATA 0xffd100e0 0x1b1b1b9b
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz +# Dram initalization for SINGLE x16 CL=5 @ 400MHz DATA 0xffd01400 0x43000c30 # DDR Configuration register # bit13-0: 0xc30, (3120 DDR2 clks refresh rate) # bit23-14: 0x0, @@ -87,7 +87,7 @@ DATA 0xffd0141c 0x00000c52 # DDR Mode # bit6-4: 0x4, CL=5 # bit7: 0x0, TestMode=0 normal # bit8: 0x0, DLL reset=0 normal -# bit11-9: 0x6, auto-precharge write recovery ???????????? +# bit11-9: 0x6, auto-precharge write recovery # bit12: 0x0, PD must be zero # bit31-13: 0x0, required
diff --git a/board/raidsonic/ib62x0/kwbimage.cfg b/board/raidsonic/ib62x0/kwbimage.cfg index 596071f..ec00c15 100644 --- a/board/raidsonic/ib62x0/kwbimage.cfg +++ b/board/raidsonic/ib62x0/kwbimage.cfg @@ -11,7 +11,7 @@ #
# Boot Media configurations -BOOT_FROM nand # change from nand to uart if building UART image +BOOT_FROM nand NAND_ECC_MODE default NAND_PAGE_SIZE 0x0800
@@ -21,12 +21,12 @@ NAND_PAGE_SIZE 0x0800 # Configure RGMII-0 interface pad voltage to 1.8V DATA 0xffd100e0 0x1b1b1b9b
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz +# Dram initalization for SINGLE x16 CL=5 @ 400MHz DATA 0xffd01400 0x43000c30 # DDR Configuration register # bit13-0: 0xc30, (3120 DDR2 clks refresh rate) # bit23-14: 0x0, -# bit24: 0x1, enable exit self refresh mode on DDR access -# bit25: 0x1, required +# bit24: 0x1, enable exit self refresh mode on DDR access +# bit25: 0x1, required # bit29-26: 0x0, # bit31-30: 0x1,
@@ -64,10 +64,10 @@ DATA 0xffd01410 0x0000000c # DDR Address Control # bit3-2: 11, Cs0size (1Gb) # bit5-4: 00, Cs1width (x8) # bit7-6: 11, Cs1size (1Gb) -# bit9-8: 00, Cs2width (nonexistent -# bit11-10: 00, Cs2size (nonexistent -# bit13-12: 00, Cs3width (nonexistent -# bit15-14: 00, Cs3size (nonexistent +# bit9-8: 00, Cs2width (nonexistent) +# bit11-10: 00, Cs2size (nonexistent) +# bit13-12: 00, Cs3width (nonexistent) +# bit15-14: 00, Cs3size (nonexistent) # bit16: 0, Cs0AddrSel # bit17: 0, Cs1AddrSel # bit18: 0, Cs2AddrSel @@ -88,7 +88,7 @@ DATA 0xffd0141c 0x00000c52 # DDR Mode # bit6-4: 0x4, CL=5 # bit7: 0x0, TestMode=0 normal # bit8: 0x0, DLL reset=0 normal -# bit11-9: 0x6, auto-precharge write recovery ???????????? +# bit11-9: 0x6, auto-precharge write recovery # bit12: 0x0, PD must be zero # bit31-13: 0x0, required
@@ -148,8 +148,8 @@ DATA 0xffd0149c 0x0000e803 # CPU ODT Control DATA 0xffd01480 0x00000001 # DDR Initialization Control # bit0: 0x1, enable DDR init upon this register write
-DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register -DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register +DATA 0xffd20134 0x66666666 # L2 RAM Timing 0 Register +DATA 0xffd20138 0x66666666 # L2 RAM Timing 1 Register
# End of Header extension DATA 0x0 0x0