From: "Mathieu J. Poirier" mathieu.poirier@linaro.org
Functions such as providing power to the MMC device and reading the processor version register should be in the cpu area for access by multiple u8500-based boards.
Signed-off-by: Mathieu Poirier mathieu.poirier@linaro.org Signed-off-by: John Rigby john.rigby@linaro.org --- arch/arm/cpu/armv7/u8500/cpu.c | 86 +++++++++++++++++++++++++++ arch/arm/include/asm/arch-u8500/sys_proto.h | 1 + board/st-ericsson/u8500/u8500_href.c | 75 +----------------------- 3 files changed, 88 insertions(+), 74 deletions(-)
diff --git a/arch/arm/cpu/armv7/u8500/cpu.c b/arch/arm/cpu/armv7/u8500/cpu.c index fece201..593199c 100644 --- a/arch/arm/cpu/armv7/u8500/cpu.c +++ b/arch/arm/cpu/armv7/u8500/cpu.c @@ -28,6 +28,30 @@ #include <asm/io.h> #include <asm/arch/prcmu.h> #include <asm/arch/clock.h> +#include <asm/arch/hardware.h> + +#include <asm/arch/hardware.h> + +#define CPUID_DB8500V1 0x411fc091 +#define CPUID_DB8500V2 0x412fc091 +#define ASICID_DB8500V11 0x008500A1 + +static unsigned int read_asicid(void) +{ + unsigned int *address = (void *)U8500_BOOTROM_BASE + + U8500_BOOTROM_ASIC_ID_OFFSET; + return readl(address); +} + +static int cpu_is_u8500v11(void) +{ + return read_asicid() == ASICID_DB8500V11; +} + +static int cpu_is_u8500v2(void) +{ + return read_cpuid() == CPUID_DB8500V2; +}
#ifdef CONFIG_ARCH_CPU_INIT /* @@ -41,3 +65,65 @@ int arch_cpu_init(void) return 0; } #endif /* CONFIG_ARCH_CPU_INIT */ + +#ifdef CONFIG_MMC + +#define LDO_VAUX3_MASK 0x3 +#define LDO_VAUX3_ENABLE 0x1 +#define VAUX3_VOLTAGE_2_9V 0xd + +#define AB8500_REGU_CTRL2 0x4 +#define AB8500_REGU_VRF1VAUX3_REGU_REG 0x040A +#define AB8500_REGU_VRF1VAUX3_SEL_REG 0x0421 + +int u8500_mmc_power_init(void) +{ + int ret; + int val; + + if (!cpu_is_u8500v11()) + return 0; + + /* + * On v1.1 HREF boards (HREF+), Vaux3 needs to be enabled for the SD + * card to work. This is done by enabling the regulators in the AB8500 + * via PRCMU I2C transactions. + * + * This code is derived from the handling of AB8500_LDO_VAUX3 in + * ab8500_ldo_enable() and ab8500_ldo_disable() in Linux. + * + * Turn off and delay is required to have it work across soft reboots. + */ + + ret = prcmu_i2c_read(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG); + if (ret < 0) + goto out; + + val = ret; + + /* Turn off */ + ret = prcmu_i2c_write(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG, + val & ~LDO_VAUX3_MASK); + if (ret < 0) + goto out; + + udelay(10 * 1000); + + /* Set the voltage to 2.9V */ + ret = prcmu_i2c_write(AB8500_REGU_CTRL2, + AB8500_REGU_VRF1VAUX3_SEL_REG, + VAUX3_VOLTAGE_2_9V); + if (ret < 0) + goto out; + + val = val & ~LDO_VAUX3_MASK; + val = val | LDO_VAUX3_ENABLE; + + /* Turn on the supply */ + ret = prcmu_i2c_write(AB8500_REGU_CTRL2, + AB8500_REGU_VRF1VAUX3_REGU_REG, val); + +out: + return ret; +} +#endif /* CONFIG_MMC */ diff --git a/arch/arm/include/asm/arch-u8500/sys_proto.h b/arch/arm/include/asm/arch-u8500/sys_proto.h index bac5e79..a8ef9e5 100644 --- a/arch/arm/include/asm/arch-u8500/sys_proto.h +++ b/arch/arm/include/asm/arch-u8500/sys_proto.h @@ -23,5 +23,6 @@ #define _SYS_PROTO_H_
void gpio_init(void); +int u8500_mmc_power_init(void);
#endif /* _SYS_PROTO_H_ */ diff --git a/board/st-ericsson/u8500/u8500_href.c b/board/st-ericsson/u8500/u8500_href.c index fe72684..e75f8b4 100644 --- a/board/st-ericsson/u8500/u8500_href.c +++ b/board/st-ericsson/u8500/u8500_href.c @@ -139,18 +139,6 @@ void show_boot_progress(int progress) } #endif
-static unsigned int read_asicid(void) -{ - unsigned int *address = (void *)U8500_BOOTROM_BASE - + U8500_BOOTROM_ASIC_ID_OFFSET; - return readl(address); -} - -int cpu_is_u8500v11(void) -{ - return read_asicid() == 0x008500A1; -} - /* * Miscellaneous platform dependent initialisations */ @@ -227,67 +215,6 @@ unsigned int addr_vall_arr[] = { };
#ifdef CONFIG_BOARD_LATE_INIT -#ifdef CONFIG_MMC - -#define LDO_VAUX3_MASK 0x3 -#define LDO_VAUX3_ENABLE 0x1 -#define VAUX3_VOLTAGE_2_9V 0xd - -#define AB8500_REGU_CTRL2 0x4 -#define AB8500_REGU_VRF1VAUX3_REGU_REG 0x040A -#define AB8500_REGU_VRF1VAUX3_SEL_REG 0x0421 - -static int hrefplus_mmc_power_init(void) -{ - int ret; - int val; - - if (!cpu_is_u8500v11()) - return 0; - - /* - * On v1.1 HREF boards (HREF+), Vaux3 needs to be enabled for the SD - * card to work. This is done by enabling the regulators in the AB8500 - * via PRCMU I2C transactions. - * - * This code is derived from the handling of AB8500_LDO_VAUX3 in - * ab8500_ldo_enable() and ab8500_ldo_disable() in Linux. - * - * Turn off and delay is required to have it work across soft reboots. - */ - - ret = prcmu_i2c_read(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG); - if (ret < 0) - goto out; - - val = ret; - - /* Turn off */ - ret = prcmu_i2c_write(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG, - val & ~LDO_VAUX3_MASK); - if (ret < 0) - goto out; - - udelay(10 * 1000); - - /* Set the voltage to 2.9V */ - ret = prcmu_i2c_write(AB8500_REGU_CTRL2, - AB8500_REGU_VRF1VAUX3_SEL_REG, - VAUX3_VOLTAGE_2_9V); - if (ret < 0) - goto out; - - val = val & ~LDO_VAUX3_MASK; - val = val | LDO_VAUX3_ENABLE; - - /* Turn on the supply */ - ret = prcmu_i2c_write(AB8500_REGU_CTRL2, - AB8500_REGU_VRF1VAUX3_REGU_REG, val); - -out: - return ret; -} -#endif /* * called after all initialisation were done, but before the generic * mmc_initialize(). @@ -314,7 +241,7 @@ int board_late_init(void) setenv("board_id", "1"); } #ifdef CONFIG_MMC - hrefplus_mmc_power_init(); + u8500_mmc_power_init();
/* * config extended GPIO pins for level shifter and