From: Marcel Ziswiler marcel.ziswiler@toradex.com
Synchronise device tree with linux v6.1-rc3.
Signed-off-by: Marcel Ziswiler marcel.ziswiler@toradex.com
---
Changes in v4: - Re-synched with v6.1-rc3.
arch/arm/dts/imx8mq-evk.dts | 43 +++++++ arch/arm/dts/imx8mq-librem5-r3.dtsi | 45 +++++++ arch/arm/dts/imx8mq-librem5-r4.dts | 20 +-- arch/arm/dts/imx8mq-librem5.dtsi | 153 +++++++++++++++++++++-- arch/arm/dts/imx8mq-u-boot.dtsi | 10 +- arch/arm/dts/imx8mq.dtsi | 19 +-- include/dt-bindings/reset/imx8mq-reset.h | 61 ++++----- 7 files changed, 281 insertions(+), 70 deletions(-) create mode 100644 arch/arm/dts/imx8mq-librem5-r3.dtsi
diff --git a/arch/arm/dts/imx8mq-evk.dts b/arch/arm/dts/imx8mq-evk.dts index 99fed35168..82387b9cb8 100644 --- a/arch/arm/dts/imx8mq-evk.dts +++ b/arch/arm/dts/imx8mq-evk.dts @@ -71,12 +71,36 @@ linux,autosuspend-period = <125>; };
+ audio_codec_bt_sco: audio-codec-bt-sco { + compatible = "linux,bt-sco"; + #sound-dai-cells = <1>; + }; + wm8524: audio-codec { #sound-dai-cells = <0>; compatible = "wlf,wm8524"; wlf,mute-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; };
+ sound-bt-sco { + compatible = "simple-audio-card"; + simple-audio-card,name = "bt-sco-audio"; + simple-audio-card,format = "dsp_a"; + simple-audio-card,bitclock-inversion; + simple-audio-card,frame-master = <&btcpu>; + simple-audio-card,bitclock-master = <&btcpu>; + + btcpu: simple-audio-card,cpu { + sound-dai = <&sai3>; + dai-tdm-slot-num = <2>; + dai-tdm-slot-width = <16>; + }; + + simple-audio-card,codec { + sound-dai = <&audio_codec_bt_sco 1>; + }; + }; + sound-wm8524 { compatible = "simple-audio-card"; simple-audio-card,name = "wm8524-audio"; @@ -386,6 +410,16 @@ status = "okay"; };
+&sai3 { + #sound-dai-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai3>; + assigned-clocks = <&clk IMX8MQ_CLK_SAI3>; + assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + status = "okay"; +}; + &snvs_pwrkey { status = "okay"; }; @@ -548,6 +582,15 @@ >; };
+ pinctrl_sai3: sai3grp { + fsl,pins = < + MX8MQ_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6 + MX8MQ_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6 + MX8MQ_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6 + MX8MQ_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0xd6 + >; + }; + pinctrl_spdif1: spdif1grp { fsl,pins = < MX8MQ_IOMUXC_SPDIF_TX_SPDIF1_OUT 0xd6 diff --git a/arch/arm/dts/imx8mq-librem5-r3.dtsi b/arch/arm/dts/imx8mq-librem5-r3.dtsi new file mode 100644 index 0000000000..e4f8b47cce --- /dev/null +++ b/arch/arm/dts/imx8mq-librem5-r3.dtsi @@ -0,0 +1,45 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2021 Purism SPC kernel@puri.sm + +/dts-v1/; + +/* + * This file describes hardware that is shared among r3 ("Dogwood") and + * later revisions of the Librem 5 so it has to be included in dts there. + */ + +#include "imx8mq-librem5.dtsi" + +/ { + model = "Purism Librem 5r3"; + compatible = "purism,librem5r3", "purism,librem5", "fsl,imx8mq"; +}; + +&accel_gyro { + mount-matrix = "1", "0", "0", + "0", "1", "0", + "0", "0", "-1"; +}; + +&bq25895 { + ti,battery-regulation-voltage = <4200000>; /* uV */ + ti,charge-current = <1500000>; /* uA */ + ti,termination-current = <144000>; /* uA */ +}; + +&camera_front { + pinctrl-0 = <&pinctrl_csi1>, <&pinctrl_r3_camera_pwr>; + shutdown-gpios = <&gpio5 4 GPIO_ACTIVE_LOW>; +}; + +&iomuxc { + pinctrl_r3_camera_pwr: r3camerapwrgrp { + fsl,pins = < + MX8MQ_IOMUXC_SPDIF_RX_GPIO5_IO4 0x83 + >; + }; +}; + +&proximity { + proximity-near-level = <25>; +}; diff --git a/arch/arm/dts/imx8mq-librem5-r4.dts b/arch/arm/dts/imx8mq-librem5-r4.dts index cbfb49aa25..1056b7981b 100644 --- a/arch/arm/dts/imx8mq-librem5-r4.dts +++ b/arch/arm/dts/imx8mq-librem5-r4.dts @@ -1,35 +1,27 @@ // SPDX-License-Identifier: (GPL-2.0+ OR MIT) -// Copyright (C) 2020 Purism SPC kernel@puri.sm +// Copyright (C) 2021 Purism SPC kernel@puri.sm
/dts-v1/;
-#include "imx8mq-librem5.dtsi" +#include "imx8mq-librem5-r3.dtsi"
/ { model = "Purism Librem 5r4"; compatible = "purism,librem5r4", "purism,librem5", "fsl,imx8mq"; };
-&accel_gyro { - mount-matrix = "1", "0", "0", - "0", "1", "0", - "0", "0", "-1"; -}; - &bat { maxim,rsns-microohm = <1667>; };
-&bq25895 { - ti,battery-regulation-voltage = <4200000>; /* uV */ - ti,charge-current = <1500000>; /* uA */ - ti,termination-current = <144000>; /* uA */ -}; - &led_backlight { led-max-microamp = <25000>; };
+&lcd_panel { + compatible = "ys,ys57pss36bh5gq"; +}; + &proximity { proximity-near-level = <10>; }; diff --git a/arch/arm/dts/imx8mq-librem5.dtsi b/arch/arm/dts/imx8mq-librem5.dtsi index 60d47c7149..ae08556b2e 100644 --- a/arch/arm/dts/imx8mq-librem5.dtsi +++ b/arch/arm/dts/imx8mq-librem5.dtsi @@ -7,6 +7,7 @@
#include "dt-bindings/input/input.h" #include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/leds/common.h> #include "dt-bindings/pwm/pwm.h" #include "dt-bindings/usb/pd.h" #include "imx8mq.dtsi" @@ -14,6 +15,7 @@ / { model = "Purism Librem 5"; compatible = "purism,librem5", "fsl,imx8mq"; + chassis-type = "handset";
backlight_dsi: backlight-dsi { compatible = "led-backlight"; @@ -36,18 +38,45 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_keys>;
- vol-down { + key-vol-down { label = "VOL_DOWN"; gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; linux,code = <KEY_VOLUMEDOWN>; debounce-interval = <50>; + wakeup-source; };
- vol-up { + key-vol-up { label = "VOL_UP"; gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; linux,code = <KEY_VOLUMEUP>; debounce-interval = <50>; + wakeup-source; + }; + }; + + led-controller { + compatible = "pwm-leds"; + + led-0 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_BLUE>; + max-brightness = <248>; + pwms = <&pwm2 0 50000 0>; + }; + + led-1 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + max-brightness = <248>; + pwms = <&pwm4 0 50000 0>; + }; + + led-2 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_RED>; + max-brightness = <248>; + pwms = <&pwm3 0 50000 0>; }; };
@@ -62,6 +91,40 @@ enable-active-high; };
+ /* + * the pinctrl for reg_csi_1v8 and reg_vcam_1v8 is added to the PMIC + * since we can't have it twice in the 2 different regulator nodes. + */ + reg_csi_1v8: regulator-csi-1v8 { + compatible = "regulator-fixed"; + regulator-name = "CAMERA_VDDIO_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <®_vdd_3v3>; + gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + /* controlled by the CAMERA_POWER_KEY HKS */ + reg_vcam_1v2: regulator-vcam-1v2 { + compatible = "regulator-fixed"; + regulator-name = "CAMERA_VDDD_1V2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + vin-supply = <®_vdd_1v8>; + enable-active-high; + }; + + reg_vcam_2v8: regulator-vcam-2v8 { + compatible = "regulator-fixed"; + regulator-name = "CAMERA_VDDA_2V8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_vdd_3v3>; + gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + reg_gnss: regulator-gnss { compatible = "regulator-fixed"; pinctrl-names = "default"; @@ -237,8 +300,13 @@ cpu-supply = <&buck2_reg>; };
+&csi1 { + status = "okay"; +}; + &ddrc { operating-points-v2 = <&ddrc_opp_table>; + status = "okay";
ddrc_opp_table: opp-table { compatible = "operating-points-v2"; @@ -283,15 +351,10 @@ };
partition@30000 { - label = "protected1"; - reg = <0x30000 0x10000>; + label = "firmware"; + reg = <0x30000 0x1d0000>; read-only; }; - - partition@40000 { - label = "rw"; - reg = <0x40000 0x1C0000>; - }; }; };
@@ -329,12 +392,24 @@ >; };
+ pinctrl_camera_pwr: camerapwrgrp { + fsl,pins = < + /* CAMERA_PWR_EN_3V3 */ + MX8MQ_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x83 + >; + }; + + pinctrl_csi1: csi1grp { + fsl,pins = < + /* CSI1_NRST */ + MX8MQ_IOMUXC_ENET_RXC_GPIO1_IO25 0x83 + >; + }; + pinctrl_charger_in: chargeringrp { fsl,pins = < /* CHRG_INT */ MX8MQ_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x80 - /* CHG_STATUS_B */ - MX8MQ_IOMUXC_NAND_ALE_GPIO3_IO0 0x80 >; };
@@ -698,6 +773,10 @@ interrupt-names = "irq";
connector { + compatible = "usb-c-connector"; + label = "USB-C"; + data-role = "dual"; + ports { #address-cells = <1>; #size-cells = <0>; @@ -725,7 +804,7 @@ compatible = "rohm,bd71837"; reg = <0x4b>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_pmic>; + pinctrl-0 = <&pinctrl_pmic>, <&pinctrl_camera_pwr>; clocks = <&pmic_osc>; clock-names = "osc"; clock-output-names = "pmic_clk"; @@ -958,6 +1037,31 @@ >; };
+ camera_front: camera@20 { + compatible = "hynix,hi846"; + reg = <0x20>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_csi1>; + clocks = <&clk IMX8MQ_CLK_CLKO2>; + assigned-clocks = <&clk IMX8MQ_CLK_CLKO2>; + assigned-clock-rates = <25000000>; + reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; + vdda-supply = <®_vcam_2v8>; + vddd-supply = <®_vcam_1v2>; + vddio-supply = <®_csi_1v8>; + rotation = <90>; + orientation = <0>; + + port { + camera1_ep: endpoint { + data-lanes = <1 2>; + link-frequencies = /bits/ 64 + <80000000 200000000 300000000>; + remote-endpoint = <&mipi1_sensor_ep>; + }; + }; + }; + backlight@36 { compatible = "ti,lm36922"; reg = <0x36>; @@ -996,6 +1100,12 @@ pinctrl-0 = <&pinctrl_i2c4>; status = "okay";
+ vcm@c { + compatible = "dongwoon,dw9714"; + reg = <0x0c>; + vcc-supply = <®_csi_1v8>; + }; + bat: fuel-gauge@36 { compatible = "maxim,max17055"; reg = <0x36>; @@ -1003,6 +1113,7 @@ interrupts = <20 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gauge>; + power-supplies = <&bq25895>; maxim,over-heat-temp = <700>; maxim,over-volt = <4500>; maxim,rsns-microohm = <5000>; @@ -1019,7 +1130,7 @@ ti,precharge-current = <130000>; /* uA */ ti,minimum-sys-voltage = <3700000>; /* uV */ ti,boost-voltage = <5000000>; /* uV */ - ti,boost-max-current = <500000>; /* uA */ + ti,boost-max-current = <1500000>; /* uA */ ti,use-vinmin-threshold = <1>; /* enable VINDPM */ ti,vinmin-threshold = <3900000>; /* uV */ monitored-battery = <&bat>; @@ -1031,6 +1142,21 @@ status = "okay"; };
+&mipi_csi1 { + status = "okay"; + + ports { + port@0 { + reg = <0>; + + mipi1_sensor_ep: endpoint { + remote-endpoint = <&camera1_ep>; + data-lanes = <1 2>; + }; + }; + }; +}; + &mipi_dsi { #address-cells = <1>; #size-cells = <0>; @@ -1174,6 +1300,7 @@ #size-cells = <0>; dr_mode = "otg"; snps,dis_u3_susphy_quirk; + usb-role-switch; status = "okay";
port@0 { diff --git a/arch/arm/dts/imx8mq-u-boot.dtsi b/arch/arm/dts/imx8mq-u-boot.dtsi index c69c6cc58b..8d385e8da4 100644 --- a/arch/arm/dts/imx8mq-u-boot.dtsi +++ b/arch/arm/dts/imx8mq-u-boot.dtsi @@ -10,23 +10,23 @@
};
-&{/soc@0} { +&soc { u-boot,dm-spl; };
-&{/soc@0/bus@30000000} { +&aips1 { u-boot,dm-spl; };
-&{/soc@0/bus@30400000} { +&aips2 { u-boot,dm-spl; };
-&{/soc@0/bus@30800000} { +&aips3 { u-boot,dm-spl; };
-&{/soc@0/bus@32c00000} { +&aips4 { u-boot,dm-spl; };
diff --git a/arch/arm/dts/imx8mq.dtsi b/arch/arm/dts/imx8mq.dtsi index 49eadb081b..19eaa52356 100644 --- a/arch/arm/dts/imx8mq.dtsi +++ b/arch/arm/dts/imx8mq.dtsi @@ -94,7 +94,7 @@ clk_ext4: clock-ext4 { compatible = "fixed-clock"; #clock-cells = <0>; - clock-frequency= <133000000>; + clock-frequency = <133000000>; clock-output-names = "clk_ext4"; };
@@ -320,7 +320,7 @@ arm,no-tick-in-suspend; };
- soc@0 { + soc: soc@0 { compatible = "fsl,imx8mq-soc", "simple-bus"; #address-cells = <1>; #size-cells = <1>; @@ -329,7 +329,7 @@ nvmem-cells = <&imx8mq_uid>; nvmem-cell-names = "soc_unique_id";
- bus@30000000 { /* AIPS1 */ + aips1: bus@30000000 { /* AIPS1 */ compatible = "fsl,aips-bus", "simple-bus"; reg = <0x30000000 0x400000>; #address-cells = <1>; @@ -507,7 +507,7 @@ <0x00030005 0x00000053>, <0x00030006 0x0000005f>, <0x00030007 0x00000071>; - #thermal-sensor-cells = <1>; + #thermal-sensor-cells = <1>; };
wdog1: watchdog@30280000 { @@ -534,7 +534,7 @@ status = "disabled"; };
- sdma2: sdma@302c0000 { + sdma2: dma-controller@302c0000 { compatible = "fsl,imx8mq-sdma","fsl,imx7d-sdma"; reg = <0x302c0000 0x10000>; interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; @@ -784,7 +784,7 @@ }; };
- bus@30400000 { /* AIPS2 */ + aips2: bus@30400000 { /* AIPS2 */ compatible = "fsl,aips-bus", "simple-bus"; reg = <0x30400000 0x400000>; #address-cells = <1>; @@ -844,7 +844,7 @@ }; };
- bus@30800000 { /* AIPS3 */ + aips3: bus@30800000 { /* AIPS3 */ compatible = "fsl,aips-bus", "simple-bus"; reg = <0x30800000 0x400000>; #address-cells = <1>; @@ -1018,6 +1018,7 @@ compatible = "fsl,sec-v4.0-job-ring"; reg = <0x1000 0x1000>; interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; };
sec_jr1: jr@2000 { @@ -1301,7 +1302,7 @@ status = "disabled"; };
- sdma1: sdma@30bd0000 { + sdma1: dma-controller@30bd0000 { compatible = "fsl,imx8mq-sdma","fsl,imx7d-sdma"; reg = <0x30bd0000 0x10000>; interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; @@ -1369,7 +1370,7 @@ }; };
- bus@32c00000 { /* AIPS4 */ + aips4: bus@32c00000 { /* AIPS4 */ compatible = "fsl,aips-bus", "simple-bus"; reg = <0x32c00000 0x400000>; #address-cells = <1>; diff --git a/include/dt-bindings/reset/imx8mq-reset.h b/include/dt-bindings/reset/imx8mq-reset.h index 9a301082d3..705870693e 100755 --- a/include/dt-bindings/reset/imx8mq-reset.h +++ b/include/dt-bindings/reset/imx8mq-reset.h @@ -28,37 +28,40 @@ #define IMX8MQ_RESET_A53_L2RESET 17 #define IMX8MQ_RESET_SW_NON_SCLR_M4C_RST 18 #define IMX8MQ_RESET_OTG1_PHY_RESET 19 -#define IMX8MQ_RESET_OTG2_PHY_RESET 20 -#define IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N 21 -#define IMX8MQ_RESET_MIPI_DSI_RESET_N 22 -#define IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N 23 -#define IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N 24 -#define IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N 25 -#define IMX8MQ_RESET_PCIEPHY 26 -#define IMX8MQ_RESET_PCIEPHY_PERST 27 -#define IMX8MQ_RESET_PCIE_CTRL_APPS_EN 28 -#define IMX8MQ_RESET_PCIE_CTRL_APPS_TURNOFF 29 -#define IMX8MQ_RESET_HDMI_PHY_APB_RESET 30 /* i.MX8MM does NOT support */ +#define IMX8MQ_RESET_OTG2_PHY_RESET 20 /* i.MX8MN does NOT support */ +#define IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N 21 /* i.MX8MN does NOT support */ +#define IMX8MQ_RESET_MIPI_DSI_RESET_N 22 /* i.MX8MN does NOT support */ +#define IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N 23 /* i.MX8MN does NOT support */ +#define IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N 24 /* i.MX8MN does NOT support */ +#define IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N 25 /* i.MX8MN does NOT support */ +#define IMX8MQ_RESET_PCIEPHY 26 /* i.MX8MN does NOT support */ +#define IMX8MQ_RESET_PCIEPHY_PERST 27 /* i.MX8MN does NOT support */ +#define IMX8MQ_RESET_PCIE_CTRL_APPS_EN 28 /* i.MX8MN does NOT support */ +#define IMX8MQ_RESET_PCIE_CTRL_APPS_TURNOFF 29 /* i.MX8MN does NOT support */ +#define IMX8MQ_RESET_HDMI_PHY_APB_RESET 30 /* i.MX8MM/i.MX8MN does NOT support */ #define IMX8MQ_RESET_DISP_RESET 31 #define IMX8MQ_RESET_GPU_RESET 32 -#define IMX8MQ_RESET_VPU_RESET 33 -#define IMX8MQ_RESET_PCIEPHY2 34 /* i.MX8MM does NOT support */ -#define IMX8MQ_RESET_PCIEPHY2_PERST 35 /* i.MX8MM does NOT support */ -#define IMX8MQ_RESET_PCIE2_CTRL_APPS_EN 36 /* i.MX8MM does NOT support */ -#define IMX8MQ_RESET_PCIE2_CTRL_APPS_TURNOFF 37 /* i.MX8MM does NOT support */ -#define IMX8MQ_RESET_MIPI_CSI1_CORE_RESET 38 /* i.MX8MM does NOT support */ -#define IMX8MQ_RESET_MIPI_CSI1_PHY_REF_RESET 39 /* i.MX8MM does NOT support */ -#define IMX8MQ_RESET_MIPI_CSI1_ESC_RESET 40 /* i.MX8MM does NOT support */ -#define IMX8MQ_RESET_MIPI_CSI2_CORE_RESET 41 /* i.MX8MM does NOT support */ -#define IMX8MQ_RESET_MIPI_CSI2_PHY_REF_RESET 42 /* i.MX8MM does NOT support */ -#define IMX8MQ_RESET_MIPI_CSI2_ESC_RESET 43 /* i.MX8MM does NOT support */ -#define IMX8MQ_RESET_DDRC1_PRST 44 -#define IMX8MQ_RESET_DDRC1_CORE_RESET 45 -#define IMX8MQ_RESET_DDRC1_PHY_RESET 46 -#define IMX8MQ_RESET_DDRC2_PRST 47 /* i.MX8MM does NOT support */ -#define IMX8MQ_RESET_DDRC2_CORE_RESET 48 /* i.MX8MM does NOT support */ -#define IMX8MQ_RESET_DDRC2_PHY_RESET 49 /* i.MX8MM does NOT support */ +#define IMX8MQ_RESET_VPU_RESET 33 /* i.MX8MN does NOT support */ +#define IMX8MQ_RESET_PCIEPHY2 34 /* i.MX8MM/i.MX8MN does NOT support */ +#define IMX8MQ_RESET_PCIEPHY2_PERST 35 /* i.MX8MM/i.MX8MN does NOT support */ +#define IMX8MQ_RESET_PCIE2_CTRL_APPS_EN 36 /* i.MX8MM/i.MX8MN does NOT support */ +#define IMX8MQ_RESET_PCIE2_CTRL_APPS_TURNOFF 37 /* i.MX8MM/i.MX8MN does NOT support */ +#define IMX8MQ_RESET_MIPI_CSI1_CORE_RESET 38 /* i.MX8MM/i.MX8MN does NOT support */ +#define IMX8MQ_RESET_MIPI_CSI1_PHY_REF_RESET 39 /* i.MX8MM/i.MX8MN does NOT support */ +#define IMX8MQ_RESET_MIPI_CSI1_ESC_RESET 40 /* i.MX8MM/i.MX8MN does NOT support */ +#define IMX8MQ_RESET_MIPI_CSI2_CORE_RESET 41 /* i.MX8MM/i.MX8MN does NOT support */ +#define IMX8MQ_RESET_MIPI_CSI2_PHY_REF_RESET 42 /* i.MX8MM/i.MX8MN does NOT support */ +#define IMX8MQ_RESET_MIPI_CSI2_ESC_RESET 43 /* i.MX8MM/i.MX8MN does NOT support */ +#define IMX8MQ_RESET_DDRC1_PRST 44 /* i.MX8MN does NOT support */ +#define IMX8MQ_RESET_DDRC1_CORE_RESET 45 /* i.MX8MN does NOT support */ +#define IMX8MQ_RESET_DDRC1_PHY_RESET 46 /* i.MX8MN does NOT support */ +#define IMX8MQ_RESET_DDRC2_PRST 47 /* i.MX8MM/i.MX8MN does NOT support */ +#define IMX8MQ_RESET_DDRC2_CORE_RESET 48 /* i.MX8MM/i.MX8MN does NOT support */ +#define IMX8MQ_RESET_DDRC2_PHY_RESET 49 /* i.MX8MM/i.MX8MN does NOT support */ +#define IMX8MQ_RESET_SW_M4C_RST 50 +#define IMX8MQ_RESET_SW_M4P_RST 51 +#define IMX8MQ_RESET_M4_ENABLE 52
-#define IMX8MQ_RESET_NUM 50 +#define IMX8MQ_RESET_NUM 53
#endif