Hi, I am trying to bring linux up on our custom board, by loading the kernel.img , canynlands.dtb and Ramdisk onto the RAM using the serial port. However the boot process is getting hung. The boot boot process stops after the following messages :
=> run flash_self ## Booting kernel from Legacy Image at 1c000000 ... Image Name: Linux-2.6.25.7-00002-geaaf8db Created: 2008-06-30 13:53:11 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1547704 Bytes = 1.5 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 1c200000 ... Image Name: Simple Embedded Linux Framework Created: 2002-10-24 9:30:38 UTC Image Type: PowerPC Linux RAMDisk Image (gzip compressed) Data Size: 1476478 Bytes = 1.4 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 1c1e0000 Booting using the fdt blob at 0x1c1e0000 Uncompressing Kernel Image ... OK Loading Ramdisk to 1fc78000, end 1fde077e ... OK Loading Device Tree to 007f9000, end 007ff0b4 ... OK
I have changed the kernel_addr, fdt_addr and the ramdisk_addr to the RAM addresses. This is the output of the printenv command :
=> printenv bootdelay=5 baudrate=115200 loads_echo= preboot=echo;echo Type "run flash_nfs" to mount root filesystem over NFS;echo hostname=canyonlands netdev=eth0 nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} ramargs=setenv bootargs root=/dev/ram rw addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}1 addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate} addmisc=setenv bootargs ${bootargs} initrd_high=30000000 kernel_addr_r=400000 fdt_addr_r=800000 ramdisk_addr_r=C00000 hostname=canyonlands bootfile=canyonlands/uImage ramdisk_file=canyonlands/uRamdisk rootpath=/opt/eldk/ppc_4xxFP flash_self=run ramargs addip addtty addmisc;bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr} flash_nfs=run nfsargs addip addtty addmisc;bootm ${kernel_addr} - ${fdt_addr} net_nfs=tftp ${kernel_addr_r} ${bootfile}; tftp ${fdt_addr_r} ${fdt_file}; run nfsargs addip a} net_self_load=tftp ${kernel_addr_r} ${bootfile};tftp ${fdt_addr_r} ${fdt_file};tftp ${ramdisk_; net_self=run net_self_load;run ramargs addip addtty addmisc;bootm ${kernel_addr_r} ${ramdisk_a} fdt_file=canyonlands/canyonlands.dtb load=tftp 200000 canyonlands/u-boot.bin update=protect off 0x01000000 FFFFFFFF;era 0x01000000 FFFFFFFF;cp.b ${fileaddr} 0x01000000 ${fv upd=run load update nload=tftp 200000 canyonlands/u-boot-nand.bin nupdate=nand erase 0 100000;nand write 200000 0 100000;setenv filesize;saveenv nupd=run nload nupdate pciconfighost=1 pcie_mode=RP:RP fdt_addr=1c1e0000 ramdisk_addr=1c200000 ram_root=run ramargs addip;bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr} ram_ws=1C000000 kernel_addr=1c000000 stdin=serial stdout=serial stderr=serial ver=U-Boot 2009.01 (Feb 25 2009 - 15:12:15) bootcmd=run flash_self bootargs=root=/dev/ram rw ip=::::canyonlands:eth0:off panic=1 console=ttyS0,115200 filesize=1687BE
Have anybody faced a similar problem?
Regards, Afzal Nadirshah