Since the introduction of pinctrl and clk driver, and the dts file, remove unneeded the pin configurations and the clock enabling code.
Signed-off-by: Wenyou Yang wenyou.yang@atmel.com ---
board/atmel/sama5d4_xplained/sama5d4_xplained.c | 109 +----------------------- 1 file changed, 1 insertion(+), 108 deletions(-)
diff --git a/board/atmel/sama5d4_xplained/sama5d4_xplained.c b/board/atmel/sama5d4_xplained/sama5d4_xplained.c index 6684276..f93bed8 100644 --- a/board/atmel/sama5d4_xplained/sama5d4_xplained.c +++ b/board/atmel/sama5d4_xplained/sama5d4_xplained.c @@ -10,54 +10,19 @@ #include <asm/arch/at91_common.h> #include <asm/arch/at91_rstc.h> #include <asm/arch/atmel_mpddrc.h> -#include <asm/arch/atmel_usba_udc.h> #include <asm/arch/gpio.h> #include <asm/arch/clk.h> #include <asm/arch/sama5d3_smc.h> #include <asm/arch/sama5d4.h> #include <atmel_hlcdc.h> -#include <atmel_mci.h> #include <lcd.h> -#include <mmc.h> #include <net.h> #include <netdev.h> #include <nand.h> -#include <spi.h> #include <version.h>
DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_ATMEL_SPI -#ifndef CONFIG_DM_SPI -int spi_cs_is_valid(unsigned int bus, unsigned int cs) -{ - return bus == 0 && cs == 0; -} -#endif - -void spi_cs_activate(struct spi_slave *slave) -{ - at91_set_pio_output(AT91_PIO_PORTC, 3, 0); -} - -void spi_cs_deactivate(struct spi_slave *slave) -{ - at91_set_pio_output(AT91_PIO_PORTC, 3, 1); -} - -static void sama5d4_xplained_spi0_hw_init(void) -{ - at91_pio3_set_a_periph(AT91_PIO_PORTC, 0, 0); /* SPI0_MISO */ - at91_pio3_set_a_periph(AT91_PIO_PORTC, 1, 0); /* SPI0_MOSI */ - at91_pio3_set_a_periph(AT91_PIO_PORTC, 2, 0); /* SPI0_SPCK */ - - at91_set_pio_output(AT91_PIO_PORTC, 3, 1); /* SPI0_CS0 */ - - /* Enable clock */ - at91_periph_clk_enable(ATMEL_ID_SPI0); -} -#endif /* CONFIG_ATMEL_SPI */ - #ifdef CONFIG_NAND_ATMEL static void sama5d4_xplained_nand_hw_init(void) { @@ -101,14 +66,6 @@ static void sama5d4_xplained_nand_hw_init(void) } #endif
-#ifdef CONFIG_CMD_USB -static void sama5d4_xplained_usb_hw_init(void) -{ - at91_set_pio_output(AT91_PIO_PORTE, 11, 1); - at91_set_pio_output(AT91_PIO_PORTE, 14, 1); -} -#endif - #ifdef CONFIG_LCD vidinfo_t panel_info = { .vl_col = 480, @@ -202,41 +159,6 @@ void lcd_show_board_info(void)
#endif /* CONFIG_LCD */
-#ifdef CONFIG_GENERIC_ATMEL_MCI -void sama5d4_xplained_mci1_hw_init(void) -{ - at91_pio3_set_c_periph(AT91_PIO_PORTE, 19, 1); /* MCI1 CDA */ - at91_pio3_set_c_periph(AT91_PIO_PORTE, 20, 1); /* MCI1 DA0 */ - at91_pio3_set_c_periph(AT91_PIO_PORTE, 21, 1); /* MCI1 DA1 */ - at91_pio3_set_c_periph(AT91_PIO_PORTE, 22, 1); /* MCI1 DA2 */ - at91_pio3_set_c_periph(AT91_PIO_PORTE, 23, 1); /* MCI1 DA3 */ - at91_pio3_set_c_periph(AT91_PIO_PORTE, 18, 0); /* MCI1 CLK */ - - /* - * As the mci io internal pull down is too strong, so if the io needs - * external pull up, the pull up resistor will be very small, if so - * the power consumption will increase, so disable the interanl pull - * down to save the power. - */ - at91_pio3_set_pio_pulldown(AT91_PIO_PORTE, 18, 0); - at91_pio3_set_pio_pulldown(AT91_PIO_PORTE, 19, 0); - at91_pio3_set_pio_pulldown(AT91_PIO_PORTE, 20, 0); - at91_pio3_set_pio_pulldown(AT91_PIO_PORTE, 21, 0); - at91_pio3_set_pio_pulldown(AT91_PIO_PORTE, 22, 0); - at91_pio3_set_pio_pulldown(AT91_PIO_PORTE, 23, 0); - - /* Enable clock */ - at91_periph_clk_enable(ATMEL_ID_MCI1); -} - -int board_mmc_init(bd_t *bis) -{ - /* Enable the power supply */ - at91_set_pio_output(AT91_PIO_PORTE, 4, 0); - - return atmel_mci_init((void *)ATMEL_BASE_MCI1); -} -#endif /* CONFIG_GENERIC_ATMEL_MCI */
#ifdef CONFIG_MACB void sama5d4_xplained_macb0_hw_init(void) @@ -268,12 +190,6 @@ static void sama5d4_xplained_serial3_hw_init(void)
int board_early_init_f(void) { - at91_periph_clk_enable(ATMEL_ID_PIOA); - at91_periph_clk_enable(ATMEL_ID_PIOB); - at91_periph_clk_enable(ATMEL_ID_PIOC); - at91_periph_clk_enable(ATMEL_ID_PIOD); - at91_periph_clk_enable(ATMEL_ID_PIOE); - sama5d4_xplained_serial3_hw_init();
return 0; @@ -284,27 +200,15 @@ int board_init(void) /* adress of boot parameters */ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-#ifdef CONFIG_ATMEL_SPI - sama5d4_xplained_spi0_hw_init(); -#endif #ifdef CONFIG_NAND_ATMEL sama5d4_xplained_nand_hw_init(); #endif -#ifdef CONFIG_GENERIC_ATMEL_MCI - sama5d4_xplained_mci1_hw_init(); -#endif #ifdef CONFIG_MACB sama5d4_xplained_macb0_hw_init(); #endif #ifdef CONFIG_LCD sama5d4_xplained_lcd_hw_init(); #endif -#ifdef CONFIG_CMD_USB - sama5d4_xplained_usb_hw_init(); -#endif -#ifdef CONFIG_USB_GADGET_ATMEL_USBA - at91_udp_hw_init(); -#endif
return 0; } @@ -324,13 +228,6 @@ int board_eth_init(bd_t *bis) rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC0, 0x00); #endif
-#ifdef CONFIG_USB_GADGET_ATMEL_USBA - usba_udc_probe(&pdata); -#ifdef CONFIG_USB_ETH_RNDIS - usb_eth_initialize(bis); -#endif -#endif - return rc; }
@@ -338,12 +235,8 @@ int board_eth_init(bd_t *bis) #ifdef CONFIG_SPL_BUILD void spl_board_init(void) { -#ifdef CONFIG_SYS_USE_MMC - sama5d4_xplained_mci1_hw_init(); -#elif CONFIG_SYS_USE_NANDFLASH +#if CONFIG_SYS_USE_NANDFLASH sama5d4_xplained_nand_hw_init(); -#elif CONFIG_SYS_USE_SERIALFLASH - sama5d4_xplained_spi0_hw_init(); #endif }