A quick overview of u-boot implementation on the treo 680...
The treo 680 has a Diskonchip G4 nand flash chip. This device has a 2k region that maps to the system bus at the reset vector in a NOR-like fashion so that it can be used as the boot device. The phone is shipped with this 2k region configured as write-protected (can't be modified) and programmed with an initial program loader (IPL). At power-up, this IPL loads the contents of two flash blocks to SDRAM and jumps to it. The capacity of the two blocks is not large enough to hold all of u-boot, so a u-boot SPL is used. To conserve flash space, these two blocks and the necessary number of subsequent blocks are programmed with a concatenated spl + u-boot image. That way, the IPL will also load a portion of u-boot proper, and when the spl runs, it relocates the portion of u-boot that the IPL has already loaded, and then resumes loading the remaining part of u-boot before jumping to it.
The default_environment is used (CONFIG_ENV_IS_NOWHERE) because I didn't think that having a writable environment was worth the cost of a flash block, although adding it would be straightforward. I abuse the CONFIG_EXTRA_ENV_SETTINGS option to specify the usbtty for the console (CONFIG_SYS_CONSOLE_IS_IN_ENV).
Support for the LCD is included, but currently it is only useful for displaying the u-boot splash screen. But if u-boot is built without the usbtty console, it does display the auto-boot progress nicely.
Signed-off-by: Mike Dunn mikedunn@newsguy.com --- CREDITS | 4 + MAINTAINERS | 3 + board/palmtreo680/Makefile | 47 +++ board/palmtreo680/flash_u-boot.c | 170 ++++++++++ board/palmtreo680/palmtreo680.c | 184 +++++++++++ board/palmtreo680/palmtreo680_spl.lds | 69 ++++ boards.cfg | 1 + doc/README.palmtreo680 | 570 +++++++++++++++++++++++++++++++++ include/configs/palmtreo680.h | 307 ++++++++++++++++++ 9 files changed, 1355 insertions(+), 0 deletions(-) create mode 100644 board/palmtreo680/Makefile create mode 100644 board/palmtreo680/flash_u-boot.c create mode 100644 board/palmtreo680/palmtreo680.c create mode 100644 board/palmtreo680/palmtreo680_spl.lds create mode 100644 doc/README.palmtreo680 create mode 100644 include/configs/palmtreo680.h
diff --git a/CREDITS b/CREDITS index 7c1458f..3b657e9 100644 --- a/CREDITS +++ b/CREDITS @@ -124,6 +124,10 @@ N: James F. Dougherty E: jfd@GigabitNetworks.COM D: Port to the MOUSSE board
+N: Mike Dunn +E: mikedunn@newsguy.com +D: Palmtreo680 board, docg4 nand flash driver + N: Dave Ellis E: DGE@sixnetio.com D: EEPROM Speedup, SXNI855T port diff --git a/MAINTAINERS b/MAINTAINERS index 1614b91..db62af1 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -650,6 +650,9 @@ Wolfgang Denk wd@denx.de imx27lite i.MX27 qong i.MX31
+Mike Dunn mikedunn@newsguy.com + palmtreo680 pxa270 + Kristoffer Ericson kristoffer.ericson@gmail.com
jornada SA1110 diff --git a/board/palmtreo680/Makefile b/board/palmtreo680/Makefile new file mode 100644 index 0000000..e729e6a --- /dev/null +++ b/board/palmtreo680/Makefile @@ -0,0 +1,47 @@ +# +# Palm Treo680 Support +# +# Copyright (C) 2013 Mike Dunn mikedunn@newsguy.com +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := palmtreo680.o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +clean: + rm -f $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/palmtreo680/flash_u-boot.c b/board/palmtreo680/flash_u-boot.c new file mode 100644 index 0000000..ee4213e --- /dev/null +++ b/board/palmtreo680/flash_u-boot.c @@ -0,0 +1,170 @@ +/* + * This file is not part of u-boot. It is a userspace Linux utility that, when + * run on the Treo 680, will program u-boot to flash. The docg4 driver *must* + * be loaded with the reliable_mode and ignore_badblocks parameters enabled: + * + * modprobe docg4 ignore_badblocks=1 reliable_mode=1 + * + * This utility writes the concatenated spl + u-boot image to the start of the + * mtd device in the format expected by the IPL/SPL. The image file and mtd + * device node are passed to the utility as arguments. + * + * When you compile this, note that it links to libmtd from mtd-utils, so ensure + * that your include and lib paths include this. + */ + +#include <stdio.h> +#include <stdlib.h> +#include <sys/stat.h> +#include <fcntl.h> +#include <string.h> +#include <sys/types.h> +#include <unistd.h> +#include <errno.h> +#include <mtd/mtd-user.h> +#include "libmtd.h" + +#define RELIABLE_BLOCKSIZE 0x10000 /* block capacity in reliable mode */ +#define STANDARD_BLOCKSIZE 0x40000 /* block capacity in normal mode */ +#define PAGESIZE 512 +#define PAGES_PER_BLOCK 512 +#define OOBSIZE 7 /* available to user (16 total) */ + +uint8_t ff_oob[OOBSIZE] = {0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff}; + +/* this is the magic number the IPL looks for (ASCII "BIPO") */ +uint8_t page0_oob[OOBSIZE] = {'B', 'I', 'P', 'O', 0xff, 0xff, 0xff}; + +int main(int argc, char * const argv[]) +{ + int devfd, datafd, num_blocks, block; + off_t file_size; + libmtd_t mtd_desc; + struct mtd_dev_info devinfo; + uint8_t *blockbuf; + char response[8]; + + if (argc != 3) { + printf("usage: %s <image file> <mtd dev node>\n", argv[0]); + exit(-1); + } + + mtd_desc = libmtd_open(); + if (mtd_desc == NULL) { + fprintf(stderr, "can't initialize libmtd\n"); + exit(-1); + } + + /* open the spl image file and mtd device */ + datafd = open(argv[1], O_RDONLY); + if (datafd == -1) { + perror(argv[1]); + exit(-1); + } + devfd = open(argv[2], O_WRONLY); + if (devfd == -1) { + perror(argv[2]); + exit(-1); + } + if (mtd_get_dev_info(mtd_desc, argv[2], &devinfo) < 0) { + fprintf(stderr, "mtd_get_dev_info failed\n"); + exit(-1); + } + + /* determine the number of blocks needed by the image */ + file_size = lseek(datafd, 0, SEEK_END); + if (file_size == (off_t)-1) { + perror("lseek"); + exit(-1); + } + num_blocks = (file_size + RELIABLE_BLOCKSIZE - 1) / RELIABLE_BLOCKSIZE; + file_size = lseek(datafd, 0, SEEK_SET); + if (file_size == (off_t)-1) { + perror("lseek"); + exit(-1); + } + printf("The mtd partition contains %d blocks\n", devinfo.eb_cnt); + printf("U-boot will occupy %d blocks\n", num_blocks); + if (num_blocks > devinfo.eb_cnt) { + fprintf(stderr, "Insufficient blocks on partition\n"); + exit(-1); + } + + printf("Do you want to proceed?\n"); + scanf("%s", response); + if ((response[0] != 'y') && (response[0] != 'Y')) { + printf("Exiting\n"); + close(devfd); + close(datafd); + exit(-1); + } + + blockbuf = malloc(RELIABLE_BLOCKSIZE); + if (blockbuf == NULL) { + perror("malloc"); + exit(-1); + } + + for (block = 0; block < num_blocks; block++) { + int ofs, page; + ssize_t read_ret; + uint8_t *pagebuf = blockbuf, *buf = blockbuf; + uint8_t *oobbuf = page0_oob; /* magic num in oob of 1st page */ + size_t len = RELIABLE_BLOCKSIZE; + int ret; + +#if 0 /* to minimize risk, require the user to erase the partition beforehand */ + printf("Block %d: erasing\r", block + 1); + ret = mtd_erase(mtd_desc, &devinfo, devfd, block); + if (ret) { + fprintf(stderr, + "\nmtd_erase on block %d returned %d\n", + block + 1, ret); + exit(-1); + } +#endif + + /* read data for one block from file */ + while (len != 0 && (read_ret = read(datafd, buf, len)) != 0) { + if (read_ret == -1) { + if (errno == EINTR) + continue; + perror("read"); + exit(-1); + } + len -= read_ret; + buf += read_ret; + } + + printf("Block %d: writing\r", block + 1); + fflush(stdout); + + for (page = 0, ofs = 0; + page < PAGES_PER_BLOCK; + page++, ofs += PAGESIZE) { + if (page & 0x04) /* Odd-numbered 2k page */ + continue; /* skipped in reliable mode */ + + ret = mtd_write(mtd_desc, &devinfo, devfd, block, ofs, + pagebuf, PAGESIZE, oobbuf, OOBSIZE, + MTD_OPS_PLACE_OOB); + if (ret) { + fprintf(stderr, + "\nmtd_write returned %d on block %d, ofs %x\n", + ret, block + 1, ofs); + exit(-1); + } + oobbuf = ff_oob; /* oob for subsequent pages */ + + if (page & 0x01) /* odd-numbered subpage */ + pagebuf += PAGESIZE; + } + } + + printf("\nDone\n"); + + close(devfd); + close(datafd); + free(blockbuf); + return 0; +} diff --git a/board/palmtreo680/palmtreo680.c b/board/palmtreo680/palmtreo680.c new file mode 100644 index 0000000..957d4a9 --- /dev/null +++ b/board/palmtreo680/palmtreo680.c @@ -0,0 +1,184 @@ +/* + * Palm Treo 680 Support + * + * Copyright (C) 2013 Mike Dunn mikedunn@newsguy.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <command.h> +#include <serial.h> +#include <nand.h> +#include <malloc.h> +#include <asm/arch/pxa-regs.h> +#include <asm/arch-pxa/pxa.h> +#include <asm/arch-pxa/regs-mmc.h> +#include <asm/io.h> +#include <asm/global_data.h> +#include <u-boot/crc.h> +#include <linux/mtd/docg4.h> + +DECLARE_GLOBAL_DATA_PTR; + +static struct nand_chip docg4_nand_chip; + +int board_init(void) +{ + /* We have RAM, disable cache */ + dcache_disable(); + icache_disable(); + + gd->bd->bi_arch_number = MACH_TYPE_TREO680; + gd->bd->bi_boot_params = 0xa0000100; + + return 0; +} + +int dram_init(void) +{ + /* IPL initializes SDRAM (we're already running from it) */ + gd->ram_size = PHYS_SDRAM_1_SIZE; + return 0; +} + +#ifdef CONFIG_LCD +void lcd_enable(void) +{ + /* power-up and enable the lcd */ + writel(0x00400000, GPSR(86)); /* enable; drive high */ + writel(0x00002000, GPSR(77)); /* power; drive high */ + writel(0x02000000, GPCR(25)); /* enable_n; drive low */ + + /* turn on LCD backlight */ + writel(0x00, PWM_CTRL0); /* set PWM for reasonable brightness */ + writel(0x1b1, PWM_PERVAL0); + writel(0xfd, PWM_PWDUTY0); + writel(0x00000040, GPSR(38)); /* backlight power on */ +} +#endif + +#ifdef CONFIG_MMC +int board_mmc_init(bd_t *bis) +{ + writel(0x00000400, GPSR(42)); /* power on */ + return pxa_mmc_register(0); +} +#endif + +void board_nand_init(void) +{ + /* we have one 128M diskonchip G4 */ + + struct mtd_info *mtd = &nand_info[0]; + struct nand_chip *nand = &docg4_nand_chip; + if (docg4_nand_init(mtd, nand, 0)) + hang(); +} + +#ifdef CONFIG_SPL_BUILD +void *memcpy(void *dest, const void *src, size_t count) +{ + unsigned long *dl = (unsigned long *)dest, *sl = (unsigned long *)src; + char *d8, *s8; + + if (src == dest) + return dest; + + /* while all data is aligned (common case), copy a word at a time */ + if ((((ulong)dest | (ulong)src) & (sizeof(*dl) - 1)) == 0) { + while (count >= sizeof(*dl)) { + *dl++ = *sl++; + count -= sizeof(*dl); + } + } + /* copy the reset one byte at a time */ + d8 = (char *)dl; + s8 = (char *)sl; + while (count--) + *d8++ = *s8++; + + return dest; +} + + +void nand_boot(void) +{ + __attribute__((noreturn)) void (*uboot)(void); + + extern const void *_start, *_end; /* boundaries of spl in memory */ + + /* size of spl; ipl loads this, and then a portion of u-boot */ + const size_t spl_image_size = ((size_t)&_end - (size_t)&_start); + + /* the flash offset of the blocks that are loaded by the spl */ + const uint32_t spl_load_offset = CONFIG_SYS_NAND_U_BOOT_OFFS + + DOCG4_IPL_LOAD_BLOCK_COUNT * DOCG4_BLOCK_SIZE; + + /* total number of bytes loaded by IPL */ + const size_t ipl_load_size = + DOCG4_IPL_LOAD_BLOCK_COUNT * DOCG4_BLOCK_CAPACITY_SPL; + + /* number of bytes of u-boot proper that was loaded by the IPL */ + const size_t ipl_uboot_load_size = ipl_load_size - spl_image_size; + + /* number of remaining bytes of u-boot that the SPL must load */ + const size_t spl_load_size = + CONFIG_SYS_NAND_U_BOOT_SIZE - ipl_load_size; + + /* memory address where we resume loading u-boot */ + void *const load_addr = + (void *)(CONFIG_SYS_NAND_U_BOOT_DST + ipl_uboot_load_size); + + /* + * Copy the portion of u-boot already read from flash by the IPL to its + * correct load address. + */ + memcpy((void *)CONFIG_SYS_NAND_U_BOOT_DST, &_end, ipl_uboot_load_size); + + /* + * Resume loading u-boot where the IPL left off. + */ + nand_spl_load_image(spl_load_offset, spl_load_size, load_addr); + +#ifdef CONFIG_NAND_ENV_DST + nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (void *)CONFIG_NAND_ENV_DST); + +#ifdef CONFIG_ENV_OFFSET_REDUND + nand_spl_load_image(CONFIG_ENV_OFFSET_REDUND, CONFIG_ENV_SIZE, + (void *)CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE); +#endif +#endif + /* + * Jump to U-Boot image + */ + uboot = (void *)CONFIG_SYS_NAND_U_BOOT_START; + (*uboot)(); +} + +void board_init_f(ulong bootflag) +{ + nand_boot(); +} + +void hang(void) +{ + for (;;) { + } +} + +#endif /* CONFIG_SPL_BUILD */ diff --git a/board/palmtreo680/palmtreo680_spl.lds b/board/palmtreo680/palmtreo680_spl.lds new file mode 100644 index 0000000..bdfa2aa --- /dev/null +++ b/board/palmtreo680/palmtreo680_spl.lds @@ -0,0 +1,69 @@ +/* + * Copyright (C) 2013 Mike Dunn mikedunn@newsguy.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +/* + * This file is a slight modification to the default pxa link script. The '*' + * wildcard is added to the section names to consolidate all the sections + * created by the -ffunction-sections and -fdata-sections compiler flags. + */ + + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + + . = ALIGN(4); + .text : + { + arch/arm/cpu/pxa/start.o (.text) + *(.text*) + } + + . = ALIGN(4); + .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) } + + . = ALIGN(4); + .data : { + *(.data*) + } + + . = ALIGN(4); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + _end = .; + + /* internal SRAM is used for the SPL's bss */ + .bss 0x5c000000 : { + __bss_start = .; + *(.bss*) + . = ALIGN(4); + __bss_end = .; + } +} diff --git a/boards.cfg b/boards.cfg index 5fc70be..72a9440 100644 --- a/boards.cfg +++ b/boards.cfg @@ -331,6 +331,7 @@ h2200 arm pxa lubbock arm pxa palmld arm pxa palmtc arm pxa +palmtreo680 arm pxa polaris arm pxa trizepsiv - - trizepsiv:POLARIS pxa255_idp arm pxa trizepsiv arm pxa diff --git a/doc/README.palmtreo680 b/doc/README.palmtreo680 new file mode 100644 index 0000000..15c09dd --- /dev/null +++ b/doc/README.palmtreo680 @@ -0,0 +1,570 @@ + +README for the Palm Treo 680. + +Copyright (C) 2013 Mike Dunn mikedunn@newsguy.com + +You may reproduce the contents of this file entirely or in part, but please +credit me by name if you do. Thanks. + + +Intro +===== + +Yes, you can program u-boot onto the flash of your Palm Treo 680 so that u-boot +(then Linux, Android, ...) runs at power-up. This document describes how, and +gives some implementation details on this port of u-boot. + +But first, I probably don't need to tell you that after doing this, your phone +will no longer run PalmOS. You *may* be able to later restore your phone to its +original state by creating a backup image of the flash before writing u-boot +(details below), but this is not heavily tested and should not be relied upon. +There is also the possibility that something may go wrong during the process of +programming u-boot, leaving you with a bricked phone. If you follow these +instructions carefully this chance will be minimized, but I do not recommend +that you program u-boot onto a phone that you can not afford to lose, and +certainly not one that contains important data that is not backed up elsewhere. +I AM NOT RESPONSIBLE FOR THE LOSS OF YOUR PHONE. DO THIS AT YOUR OWN RISK. +Having said that, feel free to send me a note cursing me out if something does +go wrong, but please tell me what happened exactly. For that matter, I'd love +to hear from you if you succeed. + +To program u-boot to your flash, you will need to boot the Linux kernel on your +phone using a PalmOS bootloader such as cocoboot. The details of building and +running Linux on your Treo (cross-compiling, creating a root filesystem, +configuring the kernel, etc) are beyond the scope of this document. + + + +Hardware Prerequisites +====================== + +A Palm Treo 680: + (dugh) + +A Palm usb cable: + You'll need this to establish a usbtty console connection to u-boot from a + desktop PC. Currently there is no support in u-boot for the pxa27x keypad + (coming soon), so a serial link must be used for the console. + These cables are still widely available if you don't already have one. + +A Linux desktop PC. + You may be able to use Windows for the u-boot console if you have a usb driver + that is compatible with the Linux usbserial driver, but for programming u-boot + to flash, you'll really want to use a Linux PC. + + + +Treo-side Software Prerequisites +================================ + +Linux bootloader for PalmOS: + + Cocoboot is the only one I'm aware of. If you don't already have this, you + can download it from + https://download.enlightenment.org/misc/Illume/Treo-650/2008-11-13/sdcard-ba... + which is a compressed tar archive of the contents of an sd card containing + cocoboot. Use mkdosfs to create a fat16 filesystem on the first primary + partition of the card, mount the partition, and extract the tar file to it. + You will probably need to edit the cocoboot.conf file to customize the + parameters passed to the kernel. + + + +Linux kernel: + + The kernel on the Treo 680 is still a little rough around the edges, and the + official kernel frequently breaks on the Treo :( A development kernel + specifically for the Treo 680 can be found on github: + http://github.com/mike-dunn/linux-treo680 + The master branch of this tree has been tested on the Treo, and I recommend + using this kernel for programming u-boot. As of this writing, there may be a + bug in the docg4 nand flash driver that sometimes causes block erasures to + fail. This has been fixed in the above tree. + + If you choose to use the official kernel, it must contain the docg4 driver that + includes the reliable_mode module parameter. This was a later enhancement to + the driver, and was merged to the kernel as of v3.8. Do not try to use an + earlier kernel that contains the docg4 driver without support for writing in + reliable mode. If you try to program u-boot to flash with the docg4 driver + loaded without the reliable_mode parameter enabled, you *will* brick your + phone! + + For the purpose of programming u-boot to flash, the following options must be + enabled in the Treo kernel's .config: + + CONFIG_MTD=y + CONFIG_MTD_CMDLINE_PARTS=y + CONFIG_MTD_CHAR=y + CONFIG_MTD_NAND_DOCG4=m + + Note that the docg4 nand driver is configured as a module, because we will + want to load and unload it with reliable_mode enabled or disabled as needed. + + You will also need to specify mtd partitions on the kernel command line. In + the instructions that follow, we will assume that the flash blocks to which + u-boot will be programmed are defined by the second partition on the device. + The u-boot config file (include/configs/palmtreo680.h) places the u-boot image + at the start of block 6 (offset 0x180000), which is the first writable + (non-protected) block on the flash (this is also where the PalmOS SPL starts). + The u-boot image occupies four blocks, so to create the u-boot partition, pass + this command line to the kernel: + mtdparts=Msys_Diskonchip_G4:1536k(protected_part)ro,1024k(bootloader_part),-(filesys_part) + This will create three partitions: + protected_part: the first six blocks, which are read-only + bootloader_part: the next four blocks, for the u-boot image + filesys_part: the remainder of the device + The mtdchar kernel device driver will use device nodes /dev/mtd0, /dev/mtd1, + and /dev/mtd2 for these partitions, respectively. Ensure that your root file + system at least has /dev/mtd1 if you are not running udev or mdev. + + +Userspace Utilities: + + In addition to everything necessary to provide a useful userspace environment + (busybox is indispensable, of course), you will need the mtd-utils package on + your root filesystem. I use version 1.5.0 of mtd-utils, and I suggest you use + this version as well, or at leat a version very close to this one, as + mtd-utils has tended to be fluid. + + Note that busybox includes a version of mtd-utils. These are deficient and + should not be used. When you run one of these utilities (nanddump, etc), + ensure you are invoking the separate executable from mtd-utils, and not the + one built into busybox. I recommend that you configure busybox with its + mtd-utils disabled to avoid any possibility of confusion. + + You will also need to cross-compile the userspace Linux utility in + board/palmtreo680/flash_u-boot.c, which we will run on the Treo to perform the + actual write of the u-boot image to flash. This utility links against libmtd + from the mtd-utils package. + + + +Desktop PC-side Software Prerequisites +====================================== + +Terminal emulator application: + minicom, kermit, etc. + + +Linux kernel: + Compiled with CONFIG_USB_SERIAL enabled. Build this as a module. + + + +Recommended (Not directly related to u-boot) +============================================ + +Working directly on the Treo's tiny screen and keypad is difficult and +error-prone. I recommend that you log into the Linux kernel running on your +Treo from your desktop PC using ethernet over usb. The desktop's kernel must be +configured with CONFIG_USB_USBNET, CONFIG_USB_NET_CDCETHER, and +CONFIG_USB_NET_CDC_SUBSET. The Treo's kernel will need CONFIG_USB_ETH, and its +init script will need to start an ssh daemon like dropbear. Note that the usb0 +network interface will not appear on the desktop PC until the Treo kernel's usb +ethernet gadget driver has initialized. You must wait for this to occur (watch +the PC's kernel log) before you can assign usb0 an ip address and log in to the +Treo. If you also build the Treo's kernel with CONFIG_IP_PNP enabled, you can +pass its ip address on the kernel command line, and obviate the need to +initialize the network interface in your init script. + +Having the Palm usb cable connected to the host has the added benefit of keeping +power supplied to your Treo, reducing the drain on the battery. If something +goes wrong while you're programming u-boot to the flash, you will have lots of +time to correct it before the battery dies. + +I have encountered a situation where the kernel is sometimes unable to mount a +root filesystem on the mmc card due to the mmc controller not coming up in time, +(and CONFIG_MMC_UNSAFE_RESUME doesn't seem to help) so I recommend that you +build a minimal root filesystem into the kernel using the kernel's initramfs +feature (CONFIG_BLK_DEV_INITRD). If you want your root filesystem on the mmc +card, your init script can mount and switch_root to the mmc card after a short +sleep. But keep in mind that in this case you won't be able to use an mmc card +to transfer files between your desktop and the Treo. Another option for +transfering files is to mount an nfs filesystem exported by the desktop PC. For +greatest convenience, you can export the root filesystem itself from your +desktop PC and switch_root to it in your init script. This will work if your +init script contains a loop that waits for you to initialize the usb0 network +interface on the desktop PC; e.g., loop while a ping to the desktop PC returns +an error. After the loop exits, do the nfs mount and call switch_root. (You +can not use the kernel nfsroot feature because the network will not be up when +the kernel expects it to be; i.e., not until you configure the usb0 interface on +the desktop.) Use the nfs 'nolock' option when mounting to avoid the need to +run a portmapper like rpcbind. + + + +Preliminaries +============= + +Once Linux is running on your Treo, you may want to perform a few sanity checks +before programming u-boot. If you are impatient and reckless, you may skip this +section, but see disclaimer at the top of this file! + +Load the docg4 driver (you did build this as a module, right?): + + $ modprobe docg4 ignore_badblocks=1 reliable_mode=1 + +We tell the driver to use the docg4's "reliable mode" when writing because this +is the format required by the initial program loader (IPL), which runs from +power-up and loads the first portion of u-boot. We must ignore bad blocks +because linux mtd uses out-of-band (oob) bytes to mark bad blocks, which will +cause the blocks written by PalmOS to be misidentified as "bad" by libmtd. + +Check the kernel log to ensure that all's well: + + $ dmesg | tail + <... snip ...> + docg4 docg4: NAND device: 128MiB Diskonchip G4 detected + 3 cmdlinepart partitions found on MTD device Msys_Diskonchip_G4 + Creating 3 MTD partitions on "Msys_Diskonchip_G4": + 0x000000000000-0x000000180000 : "protected_part" + 0x000000180000-0x000000280000 : "bootloader_part" + 0x000000280000-0x000008000000 : "filesys_part" + +Ensure that the partition boundaries are as shown. (If no partitions are shown, +did you remember to pass them to the kernel on the command line?) We will write +u-boot to bootloader_part, which starts at offset 0x180000 (block 6) and spans 4 +256k blocks. This partition is accessed through the device node /dev/mtd1. + +The docg4 contains a read-only table that identifies blocks that were marked as +bad at the factory. This table is in the page at offset 0x2000, which is within +the partition protected_part (/dev/mtd0). There is a slight chance that one or +more of the four blocks that we will use for u-boot is listed in the table, so +use nanddump to inspect the table to see if this is the case: + + $ nanddump -p -l 512 -s 0x2000 -o /dev/mtd0 + ECC failed: 0 + ECC corrected: 0 + Number of bad blocks: 0 + Number of bbt blocks: 0 + Block size 262144, page size 512, OOB size 16 + Dumping data starting at 0x00002000 and ending at 0x00002200... + 0x00002000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff + <... snip ...> + +The format of the table is simple: one bit per block, with block numbers +increasing from left to right, starting with block 0 as the most significant bit +of the first byte. A bit will be clear if the corresponding block is bad. We +want to use blocks 6 throgh 9, so both of the two least significant bits of the +first byte must be set, as must the two most significant bits of the second +byte. If this is not true in your case (you are very unlucky), you should use +the first contiguous set of four good blocks after block 6, and adjust the +partition boundaries accordingly. You will also have to change the value of +CONFIG_SYS_NAND_U_BOOT_OFFS in include/configs/palmtreo680.h and recompile +u-boot. Because the two blocks loaded by the IPL do not have to be contiguous, +but our SPL expects them to be, you will need to erase any good blocks that are +at an offset prior to CONFIG_SYS_NAND_U_BOOT_OFFS, so that the IPL does not find +the magic number in oob and load it (details below). Once you have done all +this, the instructions in this file still apply, except that the instructions +below for restoring the original PalmOS block contents may not work. + +Next, use nanddump to verify that the PalmOS SPL is where we expect it to be. +The SPL can be identified by a magic number in the oob bytes of the first page +of each of the two blocks containing the SPL image. Pages are 512 bytes in +size, so to dump the first page, plus the oob: + + $ nanddump -p -l 512 -s 0 -o /dev/mtd1 + ECC failed: 0 + ECC corrected: 0 + Number of bad blocks: 0 + Number of bbt blocks: 0 + Block size 262144, page size 512, OOB size 16 + Dumping data starting at 0x00000000 and ending at 0x00000200... + 0x00000000: 0a 00 00 ea 00 00 00 00 00 00 00 00 00 00 00 00 + <... snip ...> + 0x000001f0: 13 4c 21 60 13 4d 2a 69 13 4b 29 69 89 1a 99 42 + OOB Data: 42 49 50 4f 30 30 30 10 3a e2 00 92 be a0 11 ff + +Verify that the first seven bytes of oob data match those in the above line. +(This is ASCII "BIPO000".) + +Do the same for the next block: + $ nanddump -p -l 512 -s 0x40000 -o /dev/mtd1 + +The first seven oob bytes in last line should read: + + OOB Data: 42 49 50 4f 30 30 31 81 db 8e 8f 46 07 9b 59 ff + +(This is ASCII "BIPO001".) + +For additional assurance, verify that the next block does *not* contain SPL +data. + + $ nanddump -p -l 512 -s 0x80000 -o /dev/mtd1 + +It doesn't matter what the oob contains, as long as the first four bytes are +*not* ASCII "BIPO". PalmOS should only be using two blocks for the SPL +(although we will need four for u-boot). + +If you want, you can back up the contents of bootloader_part to a file. You may +be able to restore it later, if desired (see "Restoring PalmOS" below). + + $ nanddump -l 0x100000 -s 0 -o -f bootloader_part.orig /dev/mtd1 + +nanddump will spew voluminous warnings about uncorrectable ecc errors. This is +a consequence of reading pages that were written in reliable mode, and is +expected (these should all occur on pages in odd-numbered 2k regions; i.e., +0x800, 0xa00, 0xc00, 0xe00, 0x1800, 0x1a00, ...). The size of the file +bootloader_part.orig should be 1081344, which is 2048 pages, each of size 512 +plus 16 oob bytes. If you are using initramfs for the root filesystem, don't +forget to copy the file to permanent storage, such as an mmc card. + +If all of the above went well, you can now program u-boot. + + + +Programming u-boot +================== + +Our u-boot includes a small SPL (secondary program loader) that must be +prepended to u-boot proper. From the base u-boot source directory on your +desktop PC: + + $ cat spl/u-boot-spl.bin u-boot.bin > u-boot-concat.bin + +cd to the board/palmtreo680/ directory, and cross-compile flash_u-boot.c for the +Treo: + + $(CC) -o flash_u-boot $(CFLAGS) $(INCLUDEPATH) $(LIBPATH) flash_u-boot.c -lmtd + +Substitute variable values from your cross-compilation environment as +appropriate. Note that it links to libmtd from mtd-utils, and this must be +included in $(LIBPATH) and $(INCLUDEPATH). + +Transfer u-boot-concat.bin and the compiled flash_u-boot utility to the Treo's +root filesystem. On the Treo, cd to the directory where these files were +placed. + +Load the docg4 driver if you have not already done so. + + $ modprobe docg4 ignore_badblocks=1 reliable_mode=1 + +Erase the blocks to which we will write u-boot. + + $ flash_erase /dev/mtd1 0x00 4 + +We can now program the flash. + + ./flash_u-boot u-boot-concat.bin /dev/mtd1 + +You can use nanddump (see above) to verify that the data was written. This +time, "BIPO" should be seen in the first four oob bytes of the first page of all +four blocks in /dev/mtd1; i.e., at offsets 0x00000, 0x40000, 0x80000, 0xc0000. + +Shutdown linux, remove and re-insert the battery, hold your breath... + + + +Enjoying u-boot +=============== + +After you insert the battery, the u-boot splash screen should appear on the lcd +after a few seconds. With the usb cable connecting the Treo to your PC, in the +kernel log of your PC you should see + + <6>usb 3-1: New USB device found, idVendor=0525, idProduct=a4a6 + <6>usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 + <6>usb 3-1: Product: U-Boot 2013.01-00167-gd62ef56-dirty + <6>usb 3-1: Manufacturer: Das U-Boot + +Load the usbserial module on your desktop PC: + + $ modprobe usbserial vendor=0x0525 product=0xa4a6 + +and run your favorite terminal emulation utility (minicom, kermit, etc) with the +serial device set to /dev/ttyUSB0 (assuming this is your only usb serial +device). You should be at the u-boot console (type 'help'). + +There is not much that is unique about using u-boot on the palm treo 680. +Kernels can be loaded from mmc, flash, and from the desktop PC via kermit. You +can expand the size of the second partition on the flash to contain a kernel, or +else put the kernel(s) in their own partition. + +Nand commands work as expected, with the excepton that blocks not written by the +linux mtd subsystem may be misidentified by the u-boot docg4 driver as "bad" if +they contain data in the oob bytes. This will be the case for the blocks +containing the u-boot image, for example. To work around this, use 'nand scrub' +to erase these blocks, and 'nand read.raw' to read them. (It would be useful if +u-boot's nand commands provided a way to explicitly ignore "bad" blocks, because +read.raw does not perform ecc.) + +Currently u-boot itself can only be programmed to flash from Linux; there is no +support for reliable mode in u-boot's docg4 flash driver. This should be +corrected soon. + + + +Customizing +=========== + +If you change u-boot's configuration significantly (adding or removing +features), you may have to adjust the value of CONFIG_SYS_NAND_U_BOOT_SIZE. +This is the size of the concatenated spl + u-boot image, and tells the SPL how +many flash blocks it needs to load. It will be rounded up to the next 64k +boundary (the spl flash block capacity), so it does not have to be exact, but +you must ensure that it is not less than the actual image size. If it is larger +than the image, blocks may be needlessly loaded, but if too small, u-boot may +only be partially loaded, resulting in a boot failure (bricked phone), so better +to be too large. The flash_u-boot utility will work with any size image and +write the required number of blocks, provided that the partition is large +enough. + +As the first writable block on the device, block 6 seems to make the most sense +as the flash offset for writing u-boot (and this is where PalmOS places its +SPL). But you can place it elsewhere if you like. If you do, you need to +adjust CONFIG_SYS_NAND_U_BOOT_OFFS accordingly, and you must ensure that blocks +preceeding the ones containing u-boot do *not* have the magic number in oob (the +IPL looks for this). In other words, make sure that any blocks that previously +contained the u-boot image or PalmOS SPL are erased (and optionally written with +something else) so that the IPL does not load it. Also make sure that the new +u-boot starting offset is at the start of a flash partition (check the kernel +log after loading the docg4 driver), and pass the corresponding mtd device file +to the flash_u-boot utility. + +The u-boot built-in default environment is used because a writable environment +in flash did not seem worth the cost of a 256k flash block. But adding this +should be straightforward. + + + +Details on the SPL +================== + +The docg4 features a 2k region at the start of its address space that interfaces +to the system bus like a NOR flash. This allows the docg4 to function as a boot +ROM. The Treo 680 uses this feature. The contents of this 2k region are +protected and can not be reprogrammed (at least I don't know how to do it). +Fortunately, the code it contains does what we need to do, at least partially. +After some essential hardware initialization (like the SDRAM controller), it +runs an IPL (initial program loader) that copies 128K (no more, no less) to a +fixed address in SDRAM and then jumps to it. 128K is too small for u-boot, so +we use it to load a u-boot SPL. But since our SPL only occupies a little over +1k, we can economize on flash usage by having the IPL load a portion of u-boot +proper as well. We let the IPL load two blocks of a concatenated spl + u-boot +image, and because the SPL is placed before u-boot proper, the IPL jumps to the +SPL, which copies to its correct SDRAM address the portion of u-boot that the +IPL has already loaded, and then loads the remaining u-boot blocks. + + + +The docg4's "reliable mode" +=========================== + +This is a special mode of operation of the hardware whereby consecutive pairs of +2k regions are used in parallel (in some fashion) to store 2k of data. In other +words, the normal capacity is halved, but the data integrity is improved. In +this mode, the data is read or written from pages in even-numbered 2k regions +(regions starting at 0x000, 0x1000, 0x2000, ...), and the odd-numbered 2k +regions (regions starting at 0x800, 0x1800, 0x2800, ...) are transparently used +in parallel. In reliable mode, the odd-numbered 2k regions are not meant to be +read or written directly. + +Reliable mode is used by the IPL because there is not enough space in its 2k +footprint to implement the BCH ecc algorithm. Data that is read while reliable +mode is enabled must have been written in reliable mode, or the read fails. +However, data written in reliable mode can also be read in normal mode (just not +as reliably), but only from the even-numbered 2k regions; the odd-numbered 2k +regions appear to contain junk, and will generate ecc errors. When the IPL and +SPL read from flash, the odd-numbered 2k regions are explicitly skipped. The +same is true for the flash_u-boot utility when it writes the u-boot image in +reliable mode. + +The docg4 Linux driver supports writing in reliable mode (it is enabled by the +module parameter), but not reading. However, the u-boot docg4_spl driver does +read in reliable mode, in the same fashion as the IPL. + + + +Details on the IPL and its data format +====================================== + +Starting from block 5 and counting upward, the IPL will search for and load the +first two blocks it finds that contain a magic number in the oob of the first +page of the block. The contents are loaded to SDRAM starting at address +0xa1700000. After two blocks have been loaded, it jumps to 0xa1700000. The +number of blocks loaded and the load address in SDRAM are hard-coded; only the +flash offset of the blocks can vary at run-time (based on the presence of the +magic number). + +In addition to using the docg4's reliable mode, the IPL expects each 512 byte +page to be written redundantly in the subsequent page. The hardware is capable +of detecting bit errors (but not correcting them), and if a bit error is +detected when a page is read, the page contents are discarded and the subsequent +page is read. + +Reliable mode reduces the capacity of a block by half, and the redundant pages +reduce it by half again. As a result, the normal 256k capacity of a block is +reduced to 64k for the purposes of the IPL/SPL. + +For the sake of simplicity and uniformity, the SPL mimics the operation of the +IPL, and expects the image to be stored in the same format. + + + +Restoring PalmOS +================ + +If you backed up the contents of bootloader_part flash partition earlier, you +should be able to restore it with the shell script shown below. The first two +blocks of data contain the PalmOS SPL and were written in reliable mode, whereas +the next two blocks were written in normal mode, so the script has to load and +unload the docg4 driver. Make sure that the mtd-utils nandwrite and flash_erase +are in your path (and are not those from busybox). Also double-check that the +backup image file bootloader_part.orig is exactly 1081344 bytes in length. If +not, it was not backed up correctly. Run the script as: + + ./restore_bootpart bootloader_part.orig /dev/mtd1 + +The script will take a minute or so to run. When it finishes, you may want to +verify with nanddump that the data looks correct before you cycle power, because +if the backup or restore failed, your phone will be bricked. Note that as a +consequence of reliable mode, the odd-numbered 2k regions in the first two +blocks will not exactly match the contents of the backup file (so unfortunately +we can't simply dump the flash contents to a file and do a binary diff with the +original back-up image to verify that it was restored correctly). Also, +nanddump will report uncorrectable ecc errors when it reads those regions. + +#!/bin/sh + +if [ $# -ne 2 ]; then + echo "usage: $0: <image file> <mtd device node>" + exit 1 +fi + +# reliable mode used for the first two blocks +modprobe -r docg4 +modprobe docg4 ignore_badblocks=1 reliable_mode=1 || exit 1 + +# erase all four blocks +flash_erase $2 0 4 + +# Program the first two blocks in reliable mode. +# 2k (4 pages) is written at a time, skipping alternate 2k regions +# Note that "2k" is 2112 bytes, including 64 oob bytes +file_ofs=0 +flash_ofs=0 +page=0 +while [ $page -ne 1024 ]; do + dd if=$1 bs=2112 skip=$file_ofs count=1 | nandwrite -o -n -s $flash_ofs $2 - || exit 1 + file_ofs=$((file_ofs+2)) + flash_ofs=$((flash_ofs+0x1000)) + page=$((page+8)) +done; + +# normal mode used for the next two blocks +modprobe -r docg4 +modprobe docg4 ignore_badblocks=1 || exit 1 +dd if=$1 bs=1 skip=$file_ofs count=540672 | nandwrite -o -n -s 0x80000 $2 - || exit 1 +modprobe -r docg4 + + +TODO +==== + + - Keypad support. + - Interactive boot menu using keypad and lcd. + - Add reliable mode support to the u-boot docg4 driver. + - U-boot command that will write a new image to the bootloader partition in + flash. + - Linux FTD support. + diff --git a/include/configs/palmtreo680.h b/include/configs/palmtreo680.h new file mode 100644 index 0000000..9afc4ca --- /dev/null +++ b/include/configs/palmtreo680.h @@ -0,0 +1,307 @@ +/* + * Palm Treo 680 configuration file + * + * Copyright (C) 2013 Mike Dunn mikedunn@newsguy.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Board Configuration Options + */ +#define CONFIG_CPU_PXA27X 1 +#define CONFIG_PALMTREO680 1 + + +#define CONFIG_SYS_MALLOC_LEN (4096*1024) + +#define CONFIG_LZMA + +/* + * Serial Console Configuration + */ +#define CONFIG_PXA_SERIAL +#define CONFIG_FFUART 1 +#define CONFIG_BAUDRATE 9600 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CONFIG_CONS_INDEX 3 + +/* we have nand (although technically nand *is* flash...) */ +#define CONFIG_SYS_NO_FLASH + +#define CONFIG_LCD +/* #define CONFIG_KEYBOARD */ /* TODO */ + +/* + * Bootloader Components Configuration + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_LOADS +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_NFS +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_SETGETDCR +#undef CONFIG_CMD_SOURCE +#undef CONFIG_CMD_XIMG + +#define CONFIG_CMD_ENV +#define CONFIG_CMD_MMC +#define CONFIG_CMD_NAND + +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS + +#define CONFIG_MACH_TYPE 1230 + + +/* + * MMC Card Configuration + */ +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_PXA_MMC_GENERIC + +#define CONFIG_CMD_FAT +#define CONFIG_CMD_EXT2 +#define CONFIG_DOS_PARTITION +#endif + +/* + * LCD + */ +#ifdef CONFIG_LCD +#define CONFIG_PXA_LCD +#define CONFIG_ACX544AKN +#define CONFIG_LCD_LOGO +#define CONFIG_SYS_LCD_PXA_NO_L_BIAS /* don't configure GPIO77 as L_BIAS */ +#define LCD_BPP LCD_COLOR16 +#define CONFIG_FB_ADDR 0x5c000000 /* internal SRAM */ +#define CONFIG_CMD_BMP +#define CONFIG_SPLASH_SCREEN /* requires "splashimage" env var */ +#define CONFIG_SPLASH_SCREEN_ALIGN /* requires "splashpos" env var */ +#define CONFIG_VIDEO_BMP_GZIP +#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20) + +#endif + +/* + * KGDB + */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* kgdb serial port speed */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * HUSH Shell Configuration + */ +#define CONFIG_SYS_HUSH_PARSER 1 +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +#define CONFIG_SYS_LONGHELP +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT "$ " +#else +#define CONFIG_SYS_PROMPT "=> " +#endif +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_DEVICE_NULLDEV 1 + +/* + * Clock Configuration + */ +#undef CONFIG_SYS_CLKS_IN_HZ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_CPUSPEED 0x210 /* 416MHz ; N=2,L=16 */ + +/* + * Stack sizes + */ +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ +#endif + +/* + * DRAM Map + */ +#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ +#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */ + +#define CONFIG_SYS_DRAM_BASE 0xa0000000 +#define CONFIG_SYS_DRAM_SIZE 0x04000000 /* 64 MB DRAM */ + +#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */ +#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_DRAM_BASE +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 + + + +/* + * GPIO settings + */ +#define CONFIG_SYS_GAFR0_L_VAL 0x0E000000 +#define CONFIG_SYS_GAFR0_U_VAL 0xA500001A +#define CONFIG_SYS_GAFR1_L_VAL 0x60000002 +#define CONFIG_SYS_GAFR1_U_VAL 0xAAA07959 +#define CONFIG_SYS_GAFR2_L_VAL 0x02AAAAAA +#define CONFIG_SYS_GAFR2_U_VAL 0x41440F08 +#define CONFIG_SYS_GAFR3_L_VAL 0x56AA95FF +#define CONFIG_SYS_GAFR3_U_VAL 0x00001401 +#define CONFIG_SYS_GPCR0_VAL 0x1FF80400 +#define CONFIG_SYS_GPCR1_VAL 0x03003FC1 +#define CONFIG_SYS_GPCR2_VAL 0x01C1E000 +#define CONFIG_SYS_GPCR3_VAL 0x01C1E000 +#define CONFIG_SYS_GPDR0_VAL 0xCFF90400 +#define CONFIG_SYS_GPDR1_VAL 0xFB22BFC1 +#define CONFIG_SYS_GPDR2_VAL 0x93CDFFDF +#define CONFIG_SYS_GPDR3_VAL 0x0069FF81 +#define CONFIG_SYS_GPSR0_VAL 0x02000018 +#define CONFIG_SYS_GPSR1_VAL 0x00000000 +#define CONFIG_SYS_GPSR2_VAL 0x000C0000 +#define CONFIG_SYS_GPSR3_VAL 0x00080000 + +#define CONFIG_SYS_PSSR_VAL 0x30 + +/* + * Clock settings + */ +#define CONFIG_SYS_CKEN 0x01ffffff +#define CONFIG_SYS_CCCR 0x02000210 + +/* + * Memory settings + */ +#define CONFIG_SYS_MSC0_VAL 0x7ff844c8 +#define CONFIG_SYS_MSC1_VAL 0x7ff86ab4 +#define CONFIG_SYS_MSC2_VAL 0x7ff87ff8 +#define CONFIG_SYS_MDCNFG_VAL 0x0B880acd +#define CONFIG_SYS_MDREFR_VAL 0x201fa031 +#define CONFIG_SYS_MDMRS_VAL 0x00320032 +#define CONFIG_SYS_FLYCNFG_VAL 0x00000000 +#define CONFIG_SYS_SXCNFG_VAL 0x40044004 + +/* + * PCMCIA and CF Interfaces + */ +#define CONFIG_SYS_MECR_VAL 0x00000003 +#define CONFIG_SYS_MCMEM0_VAL 0x0001c391 +#define CONFIG_SYS_MCMEM1_VAL 0x0001c391 +#define CONFIG_SYS_MCATT0_VAL 0x0001c391 +#define CONFIG_SYS_MCATT1_VAL 0x0001c391 +#define CONFIG_SYS_MCIO0_VAL 0x00014611 +#define CONFIG_SYS_MCIO1_VAL 0x0001c391 + +/* + * USB + */ +#define CONFIG_USB_DEVICE +#define CONFIG_USB_TTY +#define CONFIG_USB_DEV_PULLUP_GPIO 114 + +/* + * SPL + */ +#define CONFIG_SPL +#define CONFIG_SPL_TEXT_BASE 0xa1700000 /* IPL loads SPL here */ +#define CONFIG_SPL_STACK 0x5c040000 /* top of internal SRAM */ +#define CONFIG_SPL_LDSCRIPT board/palmtreo680/palmtreo680_spl.lds +#define CONFIG_SPL_NAND_SUPPORT /* build libnand for spl */ +#define CONFIG_SPL_NAND_DOCG4 /* use lean docg4 nand spl driver */ + +/* + * NAND + */ +#define CONFIG_NAND_DOCG4 +#define CONFIG_SYS_NAND_SELF_INIT +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* only one device */ +#define CONFIG_SYS_NAND_BASE 0x00000000 /* mapped to reset vector */ +#define CONFIG_SYS_NAND_PAGE_SIZE 0x200 +#define CONFIG_SYS_NAND_BLOCK_SIZE 0x40000 +#define CONFIG_BITREVERSE /* needed by docg4 driver */ +#define CONFIG_BCH /* needed by docg4 driver */ + +/* + * IMPORTANT NOTE: this is the size of the concatenated spl + u-boot image. It + * will be rounded up to the next 64k boundary (the spl flash block size), so it + * does not have to be exact, but you must ensure that it is not less than the + * actual image size, or it may fail to boot (bricked phone)! + * (Tip: reduces to three blocks with lcd and mmc support removed from u-boot.) +*/ +#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x40000 /* four 64k flash blocks */ + +/* + * This is the byte offset into the flash at which the concatenated spl + u-boot + * image is placed. It must be at the start of a block (256k boundary). Blocks + * 0 - 5 are write-protected, so we start at block 6. + */ +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x180000 /* block 6 */ + +/* DRAM address to which u-boot proper is loaded (before it relocates itself) */ +#define CONFIG_SYS_NAND_U_BOOT_DST 0xa0000000 +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST + +/* passed to linker by Makefile as arg to -Ttext option */ +#define CONFIG_SYS_TEXT_BASE 0xa0000000 + +#define CONFIG_SYS_INIT_SP_ADDR 0x5c040000 /* end of internal SRAM */ + +/* + * environment + */ +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_BUILD_ENVCRC +#define CONFIG_ENV_SIZE 0x200 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_EXTRA_ENV_SETTINGS \ + "stdin=usbtty\0" \ + "stdout=usbtty\0" \ + "stderr=usbtty" +#define CONFIG_BOOTARGS \ +"mtdparts=Msys_Diskonchip_G4:1536k(protected_part)ro,1024k(bootloader_part),-(filesys_part) \ +ip=192.168.11.102:::255.255.255.0:treo:usb0" +#define CONFIG_BOOTDELAY 3 + +#if 0 /* example: try 2nd mmc partition, then nand */ +#define CONFIG_BOOTCOMMAND \ + "mmc rescan; " \ + "if mmcinfo && ext2load mmc 0:2 0xa1000000 uImage; then " \ + "bootm 0xa1000000; " \ + "elif nand read 0xa1000000 0x280000 0x240000; then " \ + "bootm 0xa1000000; " \ + "fi; " +#endif + +/* u-boot lives at end of SDRAM, so use start of SDRAM for stand alone apps */ +#define CONFIG_STANDALONE_LOAD_ADDR 0xa0000000 + +#define CONFIG_SYS_DCACHE_OFF +#define CONFIG_SYS_ICACHE_OFF + +#endif /* __CONFIG_H */