At present these subsystems are only supported in U-Boot proper but it is sometimes necessary to support them in SPL, or even TPL. Update the Kconfig and Makefile to support this. Also adjust GPIO so that it can be used in TPL if required.
Signed-off-by: Simon Glass sjg@chromium.org ---
common/spl/Kconfig | 48 +++++++++++++++++++++++++++++++++++++++++++++- drivers/Makefile | 11 ++++++----- 2 files changed, 53 insertions(+), 6 deletions(-)
diff --git a/common/spl/Kconfig b/common/spl/Kconfig index 280496fbe0b..71d36f087bc 100644 --- a/common/spl/Kconfig +++ b/common/spl/Kconfig @@ -295,6 +295,16 @@ config SPL_HASH_SUPPORT this option to build system-specific drivers for hash acceleration as part of an SPL build.
+config TPL_HASH_SUPPORT + bool "Support hashing drivers in TPL" + select SHA1 + select SHA256 + help + Enable hashing drivers in SPL. These drivers can be used to + accelerate secure boot processing in secure applications. Enable + this option to build system-specific drivers for hash acceleration + as part of an SPL build. + config SPL_DMA_SUPPORT bool "Support DMA drivers" help @@ -376,7 +386,7 @@ config SPL_FPGA_SUPPORT within SPL.
config SPL_GPIO_SUPPORT - bool "Support GPIO" + bool "Support GPIO in SPL" help Enable support for GPIOs (General-purpose Input/Output) in SPL. GPIOs allow U-Boot to read the state of an input line (high or @@ -921,6 +931,17 @@ config TPL_ENV_SUPPORT help Enable environment support in TPL. See SPL_ENV_SUPPORT for details.
+config TPL_GPIO_SUPPORT + bool "Support GPIO in TPL" + help + Enable support for GPIOs (General-purpose Input/Output) in TPL. + GPIOs allow U-Boot to read the state of an input line (high or + low) and set the state of an output line. This can be used to + drive LEDs, control power to various system parts and read user + input. GPIOs can be useful in TPL to enable a 'sign-of-life' LED, + for example. Enable this option to build the drivers in + drivers/gpio as part of an TPL build. + config TPL_I2C_SUPPORT bool "Support I2C" help @@ -956,6 +977,22 @@ config TPL_NAND_SUPPORT help Enable support for NAND in TPL. See SPL_NAND_SUPPORT for details.
+config TPL_PCI_SUPPORT + bool "Support PCI drivers" + help + Enable support for PCI in TPL. For platforms that need PCI to boot, + or must perform some init using PCI in SPL, this provides the + necessary driver support. This enables the drivers in drivers/pci + as part of a TPL build. + +config TPL_PCH_SUPPORT + bool "Support PCH drivers" + help + Enable support for PCH (Platform Controller Hub) devices in TPL. + These are used to set up GPIOs and the SPI peripheral early in + boot. This enables the drivers in drivers/pch as part of a TPL + build. + config TPL_RAM_SUPPORT bool "Support booting from RAM" help @@ -970,6 +1007,15 @@ config TPL_RAM_DEVICE be already in memory when TPL takes over, e.g. loaded by the boot ROM.
+config TPL_RTC_SUPPORT + bool "Support RTC drivers" + help + Enable RTC (Real-time Clock) support in TPL. This includes support + for reading and setting the time. Some RTC devices also have some + non-volatile (battery-backed) memory which is accessible if + needed. This enables the drivers in drivers/rtc as part of an TPL + build. + config TPL_SERIAL_SUPPORT bool "Support serial" select TPL_PRINTF diff --git a/drivers/Makefile b/drivers/Makefile index 23ea609b094..47d291948cd 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -2,20 +2,26 @@
obj-$(CONFIG_$(SPL_TPL_)CLK) += clk/ obj-$(CONFIG_$(SPL_TPL_)DM) += core/ +obj-$(CONFIG_$(SPL_TPL_)GPIO_SUPPORT) += gpio/ obj-$(CONFIG_$(SPL_TPL_)DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/ obj-$(CONFIG_$(SPL_TPL_)I2C_SUPPORT) += i2c/ +obj-$(CONFIG_$(SPL_TPL_)INPUT) += input/ obj-$(CONFIG_$(SPL_TPL_)LED) += led/ obj-$(CONFIG_$(SPL_TPL_)MMC_SUPPORT) += mmc/ obj-$(CONFIG_$(SPL_TPL_)NAND_SUPPORT) += mtd/nand/ +obj-$(CONFIG_$(SPL_TPL_)PCI_SUPPORT) += pci/ +obj-$(CONFIG_$(SPL_TPL_)PCH_SUPPORT) += pch/ obj-$(CONFIG_$(SPL_TPL_)PHY) += phy/ obj-$(CONFIG_$(SPL_TPL_)PINCTRL) += pinctrl/ obj-$(CONFIG_$(SPL_TPL_)RAM) += ram/ +obj-$(CONFIG_$(SPL_TPL_)RTC_SUPPORT) += rtc/ obj-$(CONFIG_$(SPL_TPL_)SERIAL_SUPPORT) += serial/ obj-$(CONFIG_$(SPL_TPL_)SPI_FLASH_SUPPORT) += mtd/spi/ obj-$(CONFIG_$(SPL_TPL_)SPI_SUPPORT) += spi/ obj-$(CONFIG_$(SPL_TPL_)TIMER) += timer/ obj-$(CONFIG_$(SPL_)DM_MAILBOX) += mailbox/ obj-$(CONFIG_$(SPL_)REMOTEPROC) += remoteproc/ +obj-$(CONFIG_$(SPL_TPL_)TPM) += tpm/
ifndef CONFIG_TPL_BUILD ifdef CONFIG_SPL_BUILD @@ -23,7 +29,6 @@ ifdef CONFIG_SPL_BUILD obj-$(CONFIG_SPL_BOOTCOUNT_LIMIT) += bootcount/ obj-$(CONFIG_SPL_CPU_SUPPORT) += cpu/ obj-$(CONFIG_SPL_CRYPTO_SUPPORT) += crypto/ -obj-$(CONFIG_SPL_GPIO_SUPPORT) += gpio/ obj-$(CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/ obj-$(CONFIG_ARMADA_38X) += ddr/marvell/a38x/ obj-$(CONFIG_ARMADA_XP) += ddr/marvell/axp/ @@ -39,9 +44,6 @@ obj-$(CONFIG_SPL_DMA_SUPPORT) += dma/ obj-$(CONFIG_SPL_ETH_SUPPORT) += net/ obj-$(CONFIG_SPL_ETH_SUPPORT) += net/phy/ obj-$(CONFIG_SPL_USB_ETHER) += net/phy/ -obj-$(CONFIG_SPL_PCI_SUPPORT) += pci/ -obj-$(CONFIG_SPL_PCH_SUPPORT) += pch/ -obj-$(CONFIG_SPL_RTC_SUPPORT) += rtc/ obj-$(CONFIG_SPL_MUSB_NEW_SUPPORT) += usb/musb-new/ obj-$(CONFIG_SPL_USB_GADGET_SUPPORT) += usb/gadget/ obj-$(CONFIG_SPL_USB_GADGET_SUPPORT) += usb/gadget/udc/ @@ -90,7 +92,6 @@ obj-y += scsi/ obj-y += sound/ obj-y += spmi/ obj-y += sysreset/ -obj-y += tpm/ obj-y += video/ obj-y += watchdog/ obj-$(CONFIG_QE) += qe/