From: Nathan Barrett-Morrison nathan.morrison@timesys.com
Co-developed-by: Greg Malysa greg.malysa@timesys.com Signed-off-by: Greg Malysa greg.malysa@timesys.com Co-developed-by: Ian Roberts ian.roberts@timesys.com Signed-off-by: Ian Roberts ian.roberts@timesys.com Signed-off-by: Vasileios Bimpikas vasileios.bimpikas@analog.com Signed-off-by: Utsav Agarwal utsav.agarwal@analog.com Signed-off-by: Arturs Artamonovs arturs.artamonovs@analog.com Signed-off-by: Nathan Barrett-Morrison nathan.morrison@timesys.com ---
MAINTAINERS | 1 + drivers/mmc/Kconfig | 8 +++ drivers/mmc/Makefile | 1 + drivers/mmc/adi_sdhci.c | 152 ++++++++++++++++++++++++++++++++++++++++ 4 files changed, 162 insertions(+) create mode 100644 drivers/mmc/adi_sdhci.c
diff --git a/MAINTAINERS b/MAINTAINERS index 1131c85d22..b4c00c4d5a 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -614,6 +614,7 @@ F: drivers/dma/adi_dma.c F: drivers/gpio/adp5588_gpio.c F: drivers/gpio/gpio-adi-adsp.c F: drivers/i2c/adi_i2c.c +F: drivers/mmc/adi_sdhci.c F: drivers/net/dwc_eth_qos_adi.c F: drivers/pinctrl/pinctrl-adi-adsp.c F: drivers/remoteproc/adi_sc5xx_rproc.c diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig index d0944793c9..f32c8a3c13 100644 --- a/drivers/mmc/Kconfig +++ b/drivers/mmc/Kconfig @@ -283,6 +283,14 @@ config MMC_DW_ROCKCHIP SD 3.0, SDIO 3.0 and MMC 4.5 and supports common eMMC chips as well as removeable SD and micro-SD cards.
+config MMC_SDHCI_ADI + bool "ADI SD/MMC controller support" + depends on DM_MMC && OF_CONTROL + depends on MMC_SDHCI && MMC_SDHCI_ADMA + help + This enables support for the SD/MMC controller included in some Analog + Devices SC5XX Socs. + config MMC_DW_SOCFPGA bool "SOCFPGA specific extensions for Synopsys DW Memory Card Interface" depends on ARCH_SOCFPGA diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile index 72c3fb66ce..eac8c28ee5 100644 --- a/drivers/mmc/Makefile +++ b/drivers/mmc/Makefile @@ -69,6 +69,7 @@ obj-$(CONFIG_MMC_SDHCI_MV) += mv_sdhci.o obj-$(CONFIG_MMC_SDHCI_NPCM) += npcm_sdhci.o obj-$(CONFIG_MMC_SDHCI_PIC32) += pic32_sdhci.o obj-$(CONFIG_MMC_SDHCI_ROCKCHIP) += rockchip_sdhci.o +obj-$(CONFIG_MMC_SDHCI_ADI) += adi_sdhci.o obj-$(CONFIG_MMC_SDHCI_S5P) += s5p_sdhci.o obj-$(CONFIG_MMC_SDHCI_STI) += sti_sdhci.o obj-$(CONFIG_MMC_SDHCI_TANGIER) += tangier_sdhci.o diff --git a/drivers/mmc/adi_sdhci.c b/drivers/mmc/adi_sdhci.c new file mode 100644 index 0000000000..a8484e0e7a --- /dev/null +++ b/drivers/mmc/adi_sdhci.c @@ -0,0 +1,152 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * (C) Copyright 2022 - Analog Devices, Inc. + * + * Written and/or maintained by Timesys Corporation + * + * Contact: Nathan Barrett-Morrison nathan.morrison@timesys.com + * Contact: Greg Malysa greg.malysa@timesys.com + * + * Based on Rockchip's sdhci.c file + */ + +#include <clk.h> +#include <dm.h> +#include <malloc.h> +#include <sdhci.h> +#include <asm/cache.h> + +/* 400KHz is max freq for card ID etc. Use that as min */ +#define EMMC_MIN_FREQ 400000 + +#define ADMA_BOUNDARY_ALGN SZ_128M +#define BOUNDARY_OK(addr, len) \ + (((addr) | (ADMA_BOUNDARY_ALGN - 1)) == (((addr) + (len) - 1) | \ + (ADMA_BOUNDARY_ALGN - 1))) +/* We split a descriptor for every crossing of the ADMA alignment boundary, + * so we need an additional descriptor for every expected crossing. + * As I understand it, the max expected transaction size is: + * CONFIG_SYS_MMC_MAX_BLK_COUNT * MMC_MAX_BLOCK_LEN + * + * With the way the SDHCI-ADMA driver is implemented, if ADMA_MAX_LEN was a + * clean power of two, we'd only ever need +1 descriptor as the first + * descriptor that got split would then bring the remaining DMA + * destination addresses into alignment. Unfortunately, it's currently + * hardcoded to a non-power-of-two value. + * + * If that ever becomes parameterized, ADMA max length can be set to + * 0x10000, and set this to 1. + */ +#define ADMA_POTENTIAL_CROSSINGS \ + DIV_ROUND_UP((CONFIG_SYS_MMC_MAX_BLK_COUNT * MMC_MAX_BLOCK_LEN), \ + ADMA_BOUNDARY_ALGN) +/* +1 descriptor for each crossing. + */ +#define ADMA_TABLE_EXTRA_SZ (ADMA_POTENTIAL_CROSSINGS * ADMA_DESC_LEN) + +struct adi_sdhc_plat { + struct mmc_config cfg; + struct mmc mmc; +}; + +struct adi_sdhc { + struct sdhci_host host; + void *base; +}; + +void adi_dwcmshc_adma_write_desc(struct sdhci_host *host, void **desc, + dma_addr_t addr, int len, bool end) +{ + int tmplen, offset; + + if (likely(!len || BOUNDARY_OK(addr, len))) { + sdhci_adma_write_desc(host, desc, addr, len, end); + return; + } + + offset = addr & (ADMA_BOUNDARY_ALGN - 1); + tmplen = ADMA_BOUNDARY_ALGN - offset; + sdhci_adma_write_desc(host, desc, addr, tmplen, false); + + addr += tmplen; + len -= tmplen; + sdhci_adma_write_desc(host, desc, addr, len, end); +} + +struct sdhci_ops adi_dwcmshc_sdhci_ops = { + .adma_write_desc = adi_dwcmshc_adma_write_desc, +}; + +static int adi_dwcmshc_sdhci_probe(struct udevice *dev) +{ + struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev); + struct adi_sdhc_plat *plat = dev_get_plat(dev); + struct adi_sdhc *prv = dev_get_priv(dev); + struct sdhci_host *host = &prv->host; + int max_frequency, ret; + struct clk clk; + + max_frequency = dev_read_u32_default(dev, "max-frequency", 0); + ret = clk_get_by_index(dev, 0, &clk); + + host->quirks = 0; + host->max_clk = max_frequency; + /* + * The sdhci-driver only supports 4bit and 8bit, as sdhci_setup_cfg + * doesn't allow us to clear MMC_MODE_4BIT. Consequently, we don't + * check for other bus-width values. + */ + if (host->bus_width == 8) + host->host_caps |= MMC_MODE_8BIT; + + host->mmc = &plat->mmc; + host->mmc->priv = &prv->host; + host->mmc->dev = dev; + upriv->mmc = host->mmc; + + host->ops = &adi_dwcmshc_sdhci_ops; + host->adma_desc_table = memalign(ARCH_DMA_MINALIGN, + ADMA_TABLE_SZ + ADMA_TABLE_EXTRA_SZ); + host->adma_addr = virt_to_phys(host->adma_desc_table); + + ret = sdhci_setup_cfg(&plat->cfg, host, 0, EMMC_MIN_FREQ); + if (ret) + return ret; + + return sdhci_probe(dev); +} + +static int adi_dwcmshc_sdhci_of_to_plat(struct udevice *dev) +{ + struct sdhci_host *host = dev_get_priv(dev); + + host->name = dev->name; + host->ioaddr = dev_read_addr_ptr(dev); + host->bus_width = dev_read_u32_default(dev, "bus-width", 4); + + return 0; +} + +static int adi_sdhci_bind(struct udevice *dev) +{ + struct adi_sdhc_plat *plat = dev_get_plat(dev); + + return sdhci_bind(dev, &plat->mmc, &plat->cfg); +} + +static const struct udevice_id adi_dwcmshc_sdhci_ids[] = { + { .compatible = "adi,dwc-sdhci" }, + { } +}; + +U_BOOT_DRIVER(adi_dwcmshc_sdhci_drv) = { + .name = "adi_sdhci", + .id = UCLASS_MMC, + .of_match = adi_dwcmshc_sdhci_ids, + .of_to_plat = adi_dwcmshc_sdhci_of_to_plat, + .ops = &sdhci_ops, + .bind = adi_sdhci_bind, + .probe = adi_dwcmshc_sdhci_probe, + .priv_auto = sizeof(struct adi_sdhc), + .plat_auto = sizeof(struct adi_sdhc_plat), +};