Hi,
On 29/03/18 09:51, Jagan Teki wrote:
Hi Andre,
On Wed, Mar 14, 2018 at 7:26 AM, Andre Przywara andre.przywara@arm.com wrote:
A minor update to the v3 version sent earlier this month. I reworked patch 09 to drop the direct MMC environment for 32-bit Allwinner boards as well and keep the current MMC offset. For now I also dropped the two patches changing (back) the MMC regulator. I still believe they are good to have and keep them as U-Boot specific .dtsi files in my tree, possibly posting them later again.
As the previous version, this combines the EMAC DT support update with an update of the full Linux kernel DTs for all H3, H5 and A64 boards.
Patch 01 leaves some hint in the README how to avoid the situation when overrunning U-Boot's image size on 64-bit boards. The old v2 EMAC DT update series is in patches 02-08, it prepares U-Boot's EMAC driver for using the new DT binding used in Linux, also updates the DTs to the new EMAC DT node already.
Changes to sync the whole of U-Boot's DT files for the H3, H5 and A64 SoCs to those from Linux are in the following patches. However this first requires lifting the space limit we currently have due to the raw MMC environment. Patch 09 disables that for all sunxi boards, to give us finally some space. Patches 10 and 11 consequently revert the disabling of features we saw a few weeks ago to migitate the size problem.
Patches 12-19 then bring in the Linux DTs, split by SoCs, with the .dtsi files first, then the board files.
Merging the H3 and H5 device tree files brings in significant changes, also to the structure of the .dtsi files. However U-Boot's own DT usage is pretty limited, so it doesn't matter.
The huge benefit of syncing the DTs is that we can use U-Boot's DT copy to directly pass it to the kernel, avoiding to actually load a .dtb file from somewhere. To allows seamless and automatic UEFI booting, so distribution installer images should just work (TM).
As a goodie the final patch brings in the actual SoPine + baseboard DT files, which we were completely missing so far.
This is based on sunxi/master (2d53018a0ef2).
Cheers, Andre.
Changelog v3 .. v4:
- remove MMC environment for all Allwinner boards (including 32 bit ones)
- keep MMC environment offset to the old values
- drop DT adjustments to use fixed MMC regulator
Changelog v2 .. v3: 01: added, was on the list before 02: drop redundant H5 line 03-08: unchanged 09-20: added
Changelog v1 .. v2: 01, 02, 03: unchanged 04, 05, 06, 07: added
Andre Przywara (19): sunxi: README.sunxi64: Add hint about non-debug of ARM Trusted Firmware sunxi: gpio: add missing compatible strings net: sun8i-emac: support new pinctrl DT bindings net: sun8i-emac: add support for new EMAC DT binding arm: dts: sunxi: update A64 to new EMAC binding arm: dts: sunxi: update H3 to new EMAC binding arm: dts: sunxi: update H5 to new EMAC binding net: sun8i-emac: remove support for old binding sunxi: disable direct MMC environment sunxi: revert disabling of features Revert "sunxi: Pine64: temporarily remove extra Pine64 non-plus DT" sunxi: DT: A64: update device tree file for Allwinner A64 SoC sunxi: DT: A64: update board .dts files from Linux sunxi: DT: update device tree files for Allwinner H3 and H5 SoCs sunxi: DT: H5: update board .dts files from Linux sunxi: DT: H3: update board .dts files from Linux sunxi: DT: H3: update libre-cc board .dts file sunxi: DT: H2+: update Opi-zero .dts sunxi: DT: A64: add proper SoPine baseboard device tree
I agree that we have space for now with U-Boot proper since we removed MMC raw, but why we need to Sync all the dts nodes from Linux?
The main reason for me is to allow passing U-Boot's DT to Linux - or any other OS, for that matter. This happens already automatically with the distro defaults UEFI boot: just put in an UEFI enabled USB pen drive (distro installers) and U-Boot will boot from there - without any user interaction or special boot script, without the OS providing any DTs.
Conceptually there is only one DT for each board. The fact that U-Boot has deviated has no technical reason, it's just not being updated.
it is costing some space right?
We don't care about this so much anymore. For practical reasons it would be good to stay below 984KB (from after the SPL till 1MB, where the first partition normally starts). Adding like 10 KB to the image size is nothing in there, especially when looking at the benefits - automatic boot of any OS.
becuase
- most of the nodes doesn't have proper drivers yet example: clock,
reset, spi, axp803 and some include files and etc
- Few nodes like mmc1 from bananpi-m64 doesn't need from U-Boot point-of-view
Yes, U-Boot itself does not use those - but it doesn't hurt either. We don't need to invent some notion of U-Boot DT. The DT is not an OS configuration file, it's a hardware description.
What I'm trying to say is we should anyway sync to Linux bindings and dts files, but that could be like step-by-step based on the relevant driver support with proper testing this way we can monitor the "Size" instead of adding unneeded(for now) and untested once now struggling to think about size constraints later.
I hope we will never have to deal with hard size constraint for U-Boot proper anymore. I would like to judge any increase in size by its benefit. And booting random UEFI enabled OSes out of the box is a very good rationale for adding 10KB to the image size.
Keep in mind: Eventually you have to load this DT anyway, so effectively you will save on the image size, because you avoid duplication. Actually the OS does not need to carry all supported DTs, because the only one needed is provided by U-Boot.
If are fine with this please re-work based on above points and resend the next version otherwise please comment.
I wonder if we could just merge the first few patches now, up until and including 11/19. The EMAC DT binding deviation we have at the moment is really annoying and those patches do not increase the size.
We can have a separate discussion about the rest, if you really like.
Cheers, Andre.