Provide a man-pages for the mmc command.
Signed-off-by: Jaehoon Chung jh80.chung@samsung.com --- doc/usage/index.rst | 1 + doc/usage/mmc.rst | 182 ++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 183 insertions(+) create mode 100644 doc/usage/mmc.rst
diff --git a/doc/usage/index.rst b/doc/usage/index.rst index 6c59bbadab45..15c682ceface 100644 --- a/doc/usage/index.rst +++ b/doc/usage/index.rst @@ -30,6 +30,7 @@ Shell commands load loady mbr + mmc pstore qfw sbi diff --git a/doc/usage/mmc.rst b/doc/usage/mmc.rst new file mode 100644 index 000000000000..00a21a6e12e7 --- /dev/null +++ b/doc/usage/mmc.rst @@ -0,0 +1,182 @@ +.. SPDX-License-Identifier: GPL-2.0+: + +mmc command +============ + +Synopsis +-------- + +:: + + mmc info + mmc read addr blk# cnt + mmc write addr blk# cnt + mmc erase blk# cnt + mmc rescan + mmc part + mmc dev [dev] [part] + mmc list + mmc wp + mmc bootbus <dev> <boot_bus_width> <reset_boot_bus_width> <boot_mode> + mmc bootpart-resize <dev> <dev part size MB> <RPMB part size MB> + mmc partconf <dev> [boot_ack boot_partition partition_access] + mmc rst-function <dev> <value> + +Description +----------- + +The mmc command is used to control MMC(eMMC/SD) device. + +The *mmc info* command displays information (Manufacturer ID, OEM, Name, Bus Speed, Mode, ...) of MMC device. + +The *mmc read* command reads raw data to memory address from MMC device with block offset and count. + +The *mmc write* command writes raw data to MMC device from memory address with block offset and count. + addr + memory address + blk# + start block offset + cnt + block count + +The *mmc erase* command erases MMC device from block offset until count. + blk# + start block offset + cnt + block count + +The *mmc rescan* command scans the available MMC device. + +The *mmc part* command displays the list available partition on current mmc device. + +The *mmc dev* command shows or set current mmc device. + dev + device number to change + part + partition number to change + +The *mmc list* command displays the list available devices. + +The *mmc wp* command enables "power on write protect" function for boot partitions. + +The *mmc bootbus* command sets the BOOT_BUS_WIDTH field. + BOOTU_BUS_WIDTH[177] is one of EXT_CSD register. (*Refer to eMMC specification*) + +The *mmc partconf* command shows or changes PARTITION_CONFIG field. + boot_ack + boot acknowledge value + boot_partition + boot partition to enable for boot + 0x0 + Device not boot enabled(default) + 0x1 + Boot partition1 enabled for boot + 0x2 + Boot partition2 enabled for boot + 0x7 + User area enabled for boot + others + Reserved + partition_access + partitions to access + +The *mmc-bootpart-resize* command changes sizes of boot and RPMB partitions. + dev + device number + boot part size MB + target size of boot partition + RPMB part size MB + target size of RPMB partition + +The *mmc rst-function* command changes the RST_n_FUNCTION field. + **WARNING**: This is a write-once field. (*Refer to eMMC specification*) + RST_n_FUNCTION[162] is one of EXT_CSD register. (Readable and Writable once) + 0x0 + RST_n signal is temporarily disabled (default) + 0x1 + RST_n signal is permanently enabled + 0x2 + RST_n signal is permanently disabled + 0x3 + Reserved + + +Example +------- + +The *mmc info* command displays device's capabilities: +:: + + => mmc info + Device: EXYNOS DWMMC + Manufacturer ID: 45 + OEM: 100 + Name: SDW16 + Bus Speed: 52000000 + Mode: MMC DDR52 (52MHz) + Rd Block Len: 512 + MMC version 5.0 + High Capacity: Yes + Capacity: 14.7 GiB + Bus Width: 8-bit DDR + Erase Group Size: 512 KiB + HC WP Group Size: 8 MiB + User Capacity: 14.7 GiB WRREL + Boot Capacity: 4 MiB ENH + RPMB Capacity: 4 MiB ENH + Boot area 0 is not write protected + Boot area 1 is not write protected + +The raw data can be read/written via *mmc read/write* command: +:: + + => mmc read 0x40000000 0x5000 0x100 + MMC read: dev # 0, block # 20480, count 256 ... 256 blocks read: OK + + => mmc write 0x40000000 0x5000 0x10 + MMC write: dev # 0, block # 20480, count 256 ... 256 blocks written: OK + +The partition list can be shown via *mmc part* command: +:: + + => mmc part + Partition Map for MMC device 0 -- Partition Type: DOS + + Part Start Sector Num Sectors UUID Type + 1 8192 131072 dff8751a-01 0e Boot + 2 139264 6291456 dff8751a-02 83 + 3 6430720 1048576 dff8751a-03 83 + 4 7479296 23298048 dff8751a-04 05 Extd + 5 7481344 307200 dff8751a-05 83 + 6 7790592 65536 dff8751a-06 83 + 7 7858176 16384 dff8751a-07 83 + 8 7876608 22900736 dff8751a-08 83 + +The current device can be shown or set via *mmc dev* command: +:: + + => mmc dev + switch to partitions #0, OK + mmc0(part0) is current device + => mmc dev 2 0 + switch to partitions #0, OK + mmc2 is current device + +The list of available devices can be shown via *mmc list* command: +:: + + => mmc list + mmc list + EXYNOS DWMMC: 0 (eMMC) + EXYNOS DWMMC: 2 (SD) + +Configuration +------------- + +The mmc command is only available if CONFIG_CMD_MMC=y. +Some commands need to enable more configuration. + +write, erase + CONFIG_MMC_WRITE +bootbus, bootpart-resize, partconf, rst-function + CONFIG_SUPPORT_EMMC_BOOT=y