Board support for the Guntermann & Drunck PowerPC 440 ETX module. Based on the AMCC Yosemite board support by Stefan Roese.
Signed-off-by: Dirk Eibach eibach@gdsys.de ---
Depends on [PATCH v3] ppc4xx: Improve DDR autodetect
More whitespace rework. checkpatch does not find tab after define. Grrr.
MAINTAINERS | 1 + MAKEALL | 1 + Makefile | 3 + board/gdsys/gdppc440etx/Makefile | 51 +++++ board/gdsys/gdppc440etx/config.mk | 44 +++++ board/gdsys/gdppc440etx/gdppc440etx.c | 325 +++++++++++++++++++++++++++++++++ board/gdsys/gdppc440etx/init.S | 75 ++++++++ board/gdsys/gdppc440etx/u-boot.lds | 144 +++++++++++++++ include/configs/gdppc440etx.h | 194 ++++++++++++++++++++ 9 files changed, 838 insertions(+), 0 deletions(-) create mode 100644 board/gdsys/gdppc440etx/Makefile create mode 100644 board/gdsys/gdppc440etx/config.mk create mode 100644 board/gdsys/gdppc440etx/gdppc440etx.c create mode 100644 board/gdsys/gdppc440etx/init.S create mode 100644 board/gdsys/gdppc440etx/u-boot.lds create mode 100644 include/configs/gdppc440etx.h
diff --git a/MAINTAINERS b/MAINTAINERS index 127604b..b836263 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -132,6 +132,7 @@ Jon Diekema jon.diekema@smiths-aerospace.com
Dirk Eibach eibach@gdsys.de
+ gdppc440etx PPC440EP/GR neo PPC405EP
Dave Ellis DGE@sixnetio.com diff --git a/MAKEALL b/MAKEALL index dbed268..3789bb9 100755 --- a/MAKEALL +++ b/MAKEALL @@ -188,6 +188,7 @@ LIST_4xx=" \ EXBITGEN \ fx12mm \ G2000 \ + gdppc440etx \ glacier \ haleakala \ haleakala_nand \ diff --git a/Makefile b/Makefile index befb608..d77ab3a 100644 --- a/Makefile +++ b/Makefile @@ -1315,6 +1315,9 @@ fx12mm_config: unconfig G2000_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx g2000
+gdppc440etx_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc ppc4xx gdppc440etx gdsys + hcu4_config: unconfig @mkdir -p $(obj)board/netstal/common @$(MKCONFIG) $(@:_config=) ppc ppc4xx hcu4 netstal diff --git a/board/gdsys/gdppc440etx/Makefile b/board/gdsys/gdppc440etx/Makefile new file mode 100644 index 0000000..b93f2c3 --- /dev/null +++ b/board/gdsys/gdppc440etx/Makefile @@ -0,0 +1,51 @@ +# +# (C) Copyright 2002-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS = $(BOARD).o +SOBJS = init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/gdsys/gdppc440etx/config.mk b/board/gdsys/gdppc440etx/config.mk new file mode 100644 index 0000000..045f3e9 --- /dev/null +++ b/board/gdsys/gdppc440etx/config.mk @@ -0,0 +1,44 @@ +# +# (C) Copyright 2002 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# G&D 440EP/GR ETX-Module +# + +#TEXT_BASE = 0x00001000 + +ifeq ($(ramsym),1) +TEXT_BASE = 0xFBD00000 +else +TEXT_BASE = 0xFFF80000 +endif + +PLATFORM_CPPFLAGS += -DCONFIG_440=1 + +ifeq ($(debug),1) +PLATFORM_CPPFLAGS += -DDEBUG +endif + +ifeq ($(dbcr),1) +PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000 +endif diff --git a/board/gdsys/gdppc440etx/gdppc440etx.c b/board/gdsys/gdppc440etx/gdppc440etx.c new file mode 100644 index 0000000..e1890ff --- /dev/null +++ b/board/gdsys/gdppc440etx/gdppc440etx.c @@ -0,0 +1,325 @@ +/* + * (C) Copyright 2008 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * Based on board/amcc/yosemite/yosemite.c + * (C) Copyright 2006-2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <ppc4xx.h> +#include <asm/processor.h> +#include <asm/io.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* info for FLASH chips */ +extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; + +int board_early_init_f(void) +{ + register uint reg; + + /* + * Setup the external bus controller/chip selects + */ + mfebc(xbcfg, reg); + mtebc(xbcfg, reg | 0x04000000); /* Set ATC */ + + /* + * Setup the GPIO pins + */ + + /* setup Address lines for flash size 64Meg. */ + out32(GPIO0_OSRL, in32(GPIO0_OSRL) | 0x54000000); + out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x54000000); + out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x54000000); + + /* setup emac */ + out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xC080); + out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x40); + out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x55); + out32(GPIO0_OSRH, in32(GPIO0_OSRH) | 0x50004000); + out32(GPIO0_ISR1H, in32(GPIO0_ISR1H) | 0x00440000); + + /* UART0 and UART1*/ + out32(GPIO1_TCR, in32(GPIO1_TCR) | 0x16000000); + out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x02180000); + out32(GPIO1_ISR1L, in32(GPIO1_ISR1L) | 0x00400000); + out32(GPIO1_ISR2L, in32(GPIO1_ISR2L) | 0x04010000); + + /* disable boot-eeprom WP */ + out32(GPIO0_OSRL, in32(GPIO0_OSRL) & ~0x00C00000); + out32(GPIO0_TSRL, in32(GPIO0_TSRL) & ~0x00C00000); + out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) & ~0x00C00000); + out32(GPIO0_TCR, in32(GPIO0_TCR) | 0x08000000); + out32(GPIO0_OR, in32(GPIO0_OR) & ~0x08000000); + + /* external interrupts IRQ0...3 */ + out32(GPIO1_TCR, in32(GPIO1_TCR) & ~0x00f00000); + out32(GPIO1_TSRL, in32(GPIO1_TSRL) & ~0x00005500); + out32(GPIO1_ISR1L, in32(GPIO1_ISR1L) | 0x00005500); + + + /* + * Setup the interrupt controller polarities, triggers, etc. + */ + mtdcr(uic0sr, 0xffffffff); /* clear all */ + mtdcr(uic0er, 0x00000000); /* disable all */ + mtdcr(uic0cr, 0x00000009); /* ATI & UIC1 crit are critical */ + mtdcr(uic0pr, 0xfffffe13); /* per ref-board manual */ + mtdcr(uic0tr, 0x01c00008); /* per ref-board manual */ + mtdcr(uic0vr, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr(uic0sr, 0xffffffff); /* clear all */ + + mtdcr(uic1sr, 0xffffffff); /* clear all */ + mtdcr(uic1er, 0x00000000); /* disable all */ + mtdcr(uic1cr, 0x00000000); /* all non-critical */ + mtdcr(uic1pr, 0xffffe0ff); /* per ref-board manual */ + mtdcr(uic1tr, 0x00ffc000); /* per ref-board manual */ + mtdcr(uic1vr, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr(uic1sr, 0xffffffff); /* clear all */ + + /* + * Setup other serial configuration + */ + mfsdr(sdr_pci0, reg); + mtsdr(sdr_pci0, 0x80000000 | reg); /* PCI arbiter enabled */ + mtsdr(sdr_pfc0, 0x00003e00); /* Pin function */ + mtsdr(sdr_pfc1, 0x00048000); /* Pin function: UART0 has 4 pins */ + + return 0; +} + +int misc_init_r(void) +{ + uint pbcr; + int size_val; + uint sz; + + /* Re-do sizing to get full correct info */ + mfebc(pb0cr, pbcr); + + if (gd->bd->bi_flashsize > 0x08000000) + panic("Max. flash banksize is 128 MB!\n"); + + for (sz = gd->bd->bi_flashsize, size_val = 7; + ((sz & 0x08000000) == 0) && (size_val > 0); --size_val) + sz <<= 1; + + pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17); + mtebc(pb0cr, pbcr); + + /* adjust flash start and offset */ + gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize; + gd->bd->bi_flashoffset = 0; + + /* Monitor protection ON by default */ + (void)flash_protect(FLAG_PROTECT_SET, + -CONFIG_SYS_MONITOR_LEN, + 0xffffffff, + &flash_info[0]); + + return 0; +} + +int checkboard(void) +{ + char *s = getenv("serial#"); + u8 rev; + u8 val; + + printf("Board: GDPPC440ETX - G&D PPC440EP/GR ETX-module"); + + if (s != NULL) { + puts(", serial# "); + puts(s); + } + putc('\n'); + + return 0; +} + +/* + * pci_pre_init + * + * This routine is called just prior to registering the hose and gives + * the board the opportunity to check things. Returning a value of zero + * indicates that things are bad & PCI initialization should be aborted. + * + * Different boards may wish to customize the pci controller structure + * (add regions, override default access routines, etc) or perform + * certain pre-initialization actions. + * + */ +#if defined(CONFIG_PCI) +int pci_pre_init(struct pci_controller *hose) +{ + unsigned long addr; + + /* + * Set priority for all PLB3 devices to 0. + * Set PLB3 arbiter to fair mode. + */ + mfsdr(sdr_amp1, addr); + mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00); + addr = mfdcr(plb3_acr); + mtdcr(plb3_acr, addr | 0x80000000); + + /* + * Set priority for all PLB4 devices to 0. + */ + mfsdr(sdr_amp0, addr); + mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00); + addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */ + mtdcr(plb4_acr, addr); + + /* + * Set Nebula PLB4 arbiter to fair mode. + */ + /* Segment0 */ + addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair; + addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled; + addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep; + addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep; + mtdcr(plb0_acr, addr); + + /* Segment1 */ + addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair; + addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled; + addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep; + addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep; + mtdcr(plb1_acr, addr); + + /* enable 66 MHz ext. Clock */ + out32(GPIO1_TCR, in32(GPIO1_TCR) | 0x00008000); + out32(GPIO1_OR, in32(GPIO1_OR) | 0x00008000); + + return 1; +} +#endif /* defined(CONFIG_PCI) */ + +/* + * pci_target_init + * + * The bootstrap configuration provides default settings for the pci + * inbound map (PIM). But the bootstrap config choices are limited and + * may not be sufficient for a given board. + * + */ +#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) +void pci_target_init(struct pci_controller *hose) +{ + /* + * Set up Direct MMIO registers + */ + + /* + * PowerPC440 EP PCI Master configuration. + * Map one 1Gig range of PLB/processor addresses to PCI memory space. + * PLB address 0xA0000000-0xDFFFFFFF + * ==> PCI address 0xA0000000-0xDFFFFFFF + * Use byte reversed out routines to handle endianess. + * Make this region non-prefetchable. + */ + out32r(PCIX0_PMM0MA, 0x00000000); /* disabled b4 setting */ + out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); + out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); + out32r(PCIX0_PMM0PCIHA, 0x00000000); + out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M, no prefetch, enable region */ + + out32r(PCIX0_PMM1MA, 0x00000000); /* disabled b4 setting */ + out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); + out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); + out32r(PCIX0_PMM1PCIHA, 0x00000000); + out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M, no prefetch, enable region */ + + out32r(PCIX0_PTM1MS, 0x00000001); + out32r(PCIX0_PTM1LA, 0); + out32r(PCIX0_PTM2MS, 0); + out32r(PCIX0_PTM2LA, 0); + + /* + * Set up Configuration registers + */ + + /* Program the board's subsystem id/vendor id */ + pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID, + CONFIG_SYS_PCI_SUBSYS_VENDORID); + pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID); + + /* Configure command register as bus master */ + pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER); + + /* 240nS PCI clock */ + pci_write_config_word(0, PCI_LATENCY_TIMER, 1); + + /* No error reporting */ + pci_write_config_word(0, PCI_ERREN, 0); + + pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101); + +} +#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ + +/* + * pci_master_init + * + */ +#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) +void pci_master_init(struct pci_controller *hose) +{ + unsigned short temp_short; + + /* + * Write the PowerPC440 EP PCI Configuration regs. + * Enable PowerPC440 EP to be a master on the PCI bus (PMM). + * Enable PowerPC440 EP to act as a PCI memory target (PTM). + */ + pci_read_config_word(0, PCI_COMMAND, &temp_short); + pci_write_config_word(0, PCI_COMMAND, + temp_short | PCI_COMMAND_MASTER | + PCI_COMMAND_MEMORY); +} +#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */ + +/* + * is_pci_host + * + * This routine is called to determine if a pci scan should be + * performed. With various hardware environments (especially cPCI and + * PPMC) it's insufficient to depend on the state of the arbiter enable + * bit in the strap register, or generic host/adapter assumptions. + * + * Rather than hard-code a bad assumption in the general 440 code, the + * 440 pci code requires the board to decide at runtime. + * + * Return 0 for adapter mode, non-zero for host (monarch) mode. + * + * + */ +#if defined(CONFIG_PCI) +int is_pci_host(struct pci_controller *hose) +{ + return 1; +} +#endif /* defined(CONFIG_PCI) */ diff --git a/board/gdsys/gdppc440etx/init.S b/board/gdsys/gdppc440etx/init.S new file mode 100644 index 0000000..0bbd45a --- /dev/null +++ b/board/gdsys/gdppc440etx/init.S @@ -0,0 +1,75 @@ +/* +* (C) Copyright 2008 +* Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de +* +* based on board/amcc/yosemite/init.S +* original Copyright not specified there +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#include <ppc_asm.tmpl> +#include <config.h> + +#include <asm/mmu.h> + +/************************************************************************** + * TLB TABLE + * + * This table is used by the cpu boot code to setup the initial tlb + * entries. Rather than make broad assumptions in the cpu source tree, + * this table lets each board set things up however they like. + * + * Pointer to the table is returned in r1 + * + *************************************************************************/ + + .section .bootpg,"ax" + .globl tlbtab + +tlbtab: + tlbtab_start + + /* + * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use + * the speed up boot process. It is patched after relocation to enable SA_I + */ + tlbentry( CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, + 0, AC_R|AC_W|AC_X|SA_G/*|SA_I*/) + + /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ + tlbentry( CONFIG_SYS_INIT_RAM_ADDR, SZ_64K, CONFIG_SYS_INIT_RAM_ADDR, + 0, AC_R|AC_W|AC_X|SA_G ) + + tlbentry( CONFIG_SYS_SDRAM_BASE, SZ_256M, CONFIG_SYS_SDRAM_BASE, + 0, AC_R|AC_W|AC_X|SA_G|SA_I ) + tlbentry( CONFIG_SYS_PCI_BASE, SZ_256M, CONFIG_SYS_PCI_BASE, + 0, AC_R|AC_W|SA_G|SA_I ) + + /* PCI */ + tlbentry( CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, + 0, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, + 0, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, + 0, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, + 0, AC_R|AC_W|SA_G|SA_I ) + + tlbtab_end diff --git a/board/gdsys/gdppc440etx/u-boot.lds b/board/gdsys/gdppc440etx/u-boot.lds new file mode 100644 index 0000000..1df817b --- /dev/null +++ b/board/gdsys/gdppc440etx/u-boot.lds @@ -0,0 +1,144 @@ +/* + * (C) Copyright 2002 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + .bootpg 0xFFFFF000 : + { + cpu/ppc4xx/start.o (.bootpg) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + cpu/ppc4xx/start.o (.text) + board/gdsys/gdppc440etx/init.o (.text) + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss (NOLOAD) : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + . = ALIGN(4); + } + _end = . ; + PROVIDE (end = .); +} diff --git a/include/configs/gdppc440etx.h b/include/configs/gdppc440etx.h new file mode 100644 index 0000000..d193919 --- /dev/null +++ b/include/configs/gdppc440etx.h @@ -0,0 +1,194 @@ +/* + * (C) Copyright 2008 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * Based on include/configs/yosemite.h + * (C) Copyright 2005-2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * gdppc440etx.h - configuration for G&D 440EP/GR ETX-Module + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_440GR 1 /* Specific PPC440GR support */ +#define CONFIG_HOSTNAME gdppc440etx +#define CONFIG_440 1 /* ... PPC440 family */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */ + +/* + * Include common defines/options for all AMCC eval boards + */ +#include "amcc-common.h" + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f*/ +#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */ +#define CONFIG_SYS_PCI_MEMBASE 0xa0000000 /* mapped pci memory */ +#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 + +/*Don't change either of these*/ +#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripheral*/ +#define CONFIG_SYS_PCI_BASE 0xe0000000 /* internal PCI regs */ +/*Don't change either of these*/ + +#define CONFIG_SYS_USB_DEVICE 0x50000000 +#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000 + +/* + * Initial RAM & stack pointer (placed in SDRAM) + */ +#define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram*/ +#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */ +#define CONFIG_SYS_INIT_RAM_END (4 << 10) +#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes init data*/ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END \ + - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* + * Serial Port + */ +#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ +#define CONFIG_UART1_CONSOLE + +/* + * Environment + * Define here the location of the environment variables (FLASH or EEPROM). + * Note: DENX encourages to use redundant environment in FLASH. + */ +#define CONFIG_ENV_IS_IN_FLASH 1 /* FLASH for env. vars*/ + +/* + * FLASH related + */ +#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible*/ +#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ +#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 /* AMD RESET for STM 29W320DB!*/ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors/chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout/Flash Erase (in ms)*/ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout/Flash Write (in ms)*/ + +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1/* use buffered writes (20x faster)*/ + +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ + +#ifdef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector*/ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Env. Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) +#endif /* CONFIG_ENV_IS_IN_FLASH */ + +/* + * DDR SDRAM + */ +#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup*/ +#define CONFIG_SYS_KBYTES_SDRAM (128 * 1024) /* 128MB */ +#define CONFIG_SYS_SDRAM_BANKS (2) + +#define CONFIG_SDRAM_BANK0 +#define CONFIG_SDRAM_BANK1 + +#define CONFIG_SYS_SDRAM0_TR0 0x410a4012 +#define CONFIG_SYS_SDRAM0_WDDCTR 0x40000000 +#define CONFIG_SYS_SDRAM0_RTR 0x04080000 +#define CONFIG_SYS_SDRAM0_CFG0 0x80000000 + +#undef CONFIG_SDRAM_ECC + +/* + * I2C + */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed+slave address*/ + +/* + * Default environment variables + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + "kernel_addr=fc000000\0" \ + "ramdisk_addr=fc180000\0" \ + "" + +#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ +#define CONFIG_PHY_ADDR 1 +#define CONFIG_PHY1_ADDR 3 + +#ifdef DEBUG +#define CONFIG_PANIC_HANG +#endif + +/* + * Commands additional to the ones defined in amcc-common.h + */ +#define CONFIG_CMD_PCI +#undef CONFIG_CMD_EEPROM + +/* + * PCI stuff + */ + +/* General PCI */ +#define CONFIG_PCI /* include pci support */ +#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup*/ +#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to \ + CONFIG_SYS_PCI_MEMBASE*/ + +/* Board-specific PCI */ +#define CONFIG_SYS_PCI_TARGET_INIT +#define CONFIG_SYS_PCI_MASTER_INIT + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* tbd */ + +/* + * External Bus Controller (EBC) Setup + */ +#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE + +/* Memory Bank 0 (NOR-FLASH) initialization */ +#define CONFIG_SYS_EBC_PB0AP 0x03017200 +#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0xda000) + +#endif /* __CONFIG_H */