Hi
Il dom 19 giu 2022, 16:47 Heiko Thiery heiko.thiery@gmail.com ha scritto:
Hi,
Am So., 19. Juni 2022 um 16:40 Uhr schrieb Michael Nazzareno Trimarchi michael@amarulasolutions.com:
Hi Heiko
On Sun, Jun 19, 2022 at 8:12 AM Heiko Thiery heiko.thiery@gmail.com
wrote:
Hi,
Am So., 19. Juni 2022 um 07:59 Uhr schrieb Michael Nazzareno Trimarchi michael@amarulasolutions.com:
Hi
Il sab 18 giu 2022, 23:56 Heiko Thiery heiko.thiery@gmail.com ha
scritto:
Hi Michael, Hi Marek,
Am Mi., 15. Juni 2022 um 08:43 Uhr schrieb Michael Nazzareno
Trimarchi
Hi Heiko
On Wed, Jun 15, 2022 at 8:23 AM Heiko Thiery <
heiko.thiery@gmail.com> wrote:
> > Hi Marek, > > [SNIP] > > > > diff --git a/board/freescale/imx8mn_evk/spl.c
b/board/freescale/imx8mn_evk/spl.c
> > > index 14cb51368f..0d9909a662 100644 > > > --- a/board/freescale/imx8mn_evk/spl.c > > > +++ b/board/freescale/imx8mn_evk/spl.c > > > @@ -83,6 +83,15 @@ int power_init_board(void) > > > #ifdef CONFIG_IMX8MN_LOW_DRIVE_MODE > > > /* Set VDD_SOC/VDD_DRAM to 0.8v for low drive mode
*/
> > > pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x10); > > > +#elif defined(CONFIG_TARGET_IMX8MN_DDR3L_EVK) > > > + /* Set VDD_SOC to 0.85v for DDR3L at 1600MTS */ > > > + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x14); > > > + > > > + /* Disable the BUCK2 */ > > > + pmic_reg_write(dev, PCA9450_BUCK2CTRL, 0x48); > > > + > > > + /* Set NVCC_DRAM to 1.35v */ > > > + pmic_reg_write(dev, PCA9450_BUCK6OUT, 0x1E); > > > #else > > > > All this part is not done by the spl pmic driver? > > I saw that you added the PCA9450 driver. Do you know if this > initialization can be done by the driver when
CONFIG_SPL_DM_REGULATOR
> is enabled? If I see this correctly, it can't be done. Is that > correct?
+&i2c1 {
u-boot,dm-spl;+};
+&{/soc@0/bus@30800000/i2c@30a20000/pmic@4b} {
u-boot,dm-spl;+};
+&{/soc@0/bus@30800000/i2c@30a20000/pmic@4b/regulators} {
u-boot,dm-spl;+};
+&pinctrl_i2c1 {
u-boot,dm-spl;+};
+&pinctrl_pmic {
u-boot,dm-spl;+};
Maybe something like this should work. Now question is about
should be
done in pre-reloc or not
It took me a little while to understand what was meant by this. In
the
meantime I could change the PMIC/Regulator initialization to DT/DM and can make the
setting so.
What is not clear to me yet is at which point this should be done (regulators_enable_boot_on()). Currently I do it in the board/spl specific board_init_f().
Do any of you have any advice here?
After having a discussion with you, i found that maybe i have some
problem and some of the setting should be done before ddr inizialization. I will take a look on it on afternoon. I know marek was working on some way to probe driver during binding and we need even to be sure that this can happen before memory training.
Currently I added it in board_init_f() right before spl_dram_init() [1] and it works. I also tried to put it in power_init_board() [2] but this does not work.
[1]
https://elixir.bootlin.com/u-boot/v2022.04/source/board/freescale/imx8mn_evk...
[2]
https://elixir.bootlin.com/u-boot/v2022.04/source/board/freescale/imx8mn_evk...
Does it work if you mark pre-reoloc, pmic, i2c, and pinctrl?
I added on all nodes the u-boot,dm-pre-reloc but this does not help when trying to do the init in power_init_board().
From code I navigate spl_early_init should bind the driver in pre-reloc
Michael
Michael
-- Heiko
Michael
Thanks
Heiko
Michael > > -- > Heiko
-- Michael Nazzareno Trimarchi Co-Founder & Chief Executive Officer M. +39 347 913 2170 michael@amarulasolutions.com __________________________________
Amarula Solutions BV Joop Geesinkweg 125, 1114 AB, Amsterdam, NL T. +31 (0)85 111 9172 info@amarulasolutions.com www.amarulasolutions.com
-- Michael Nazzareno Trimarchi Co-Founder & Chief Executive Officer M. +39 347 913 2170 michael@amarulasolutions.com __________________________________
Amarula Solutions BV Joop Geesinkweg 125, 1114 AB, Amsterdam, NL T. +31 (0)85 111 9172 info@amarulasolutions.com www.amarulasolutions.com