Hi Wolfgang
I tried with kermit again. Following is the console log when file is getting transfered.
################################### C-Kermit 8.0.211, 10 Apr 2004, chetan-laptop
Current Directory: /media/DISK_VOL2/Work/beagleboard/sw/code/testApp Communication Device: /dev/ttyUSB0 Communication Speed: 115200 Parity: none RTT/Timeout: 01 / 02 SENDING: uImage => uImage File Type: BINARY File Size: 1911160 Percent Done: 2 / ...10...20...30...40...50...60...70...80...90..100 Estimated Time Left: 00:05:38 Transfer Rate, CPS: 5512 Window Slots: 1 of 1 Packet Type: D Packet Count: 79 Packet Length: 609 Error Count: 32 Last Error: (resend) Last Message:
X to cancel file, Z to cancel group, <CR> to resend last packet, ############################
As there is considerable difference between the logs I am getting and logs you have provided in you last mail.
e.g Communication device is /dev/ttyUSB0 (in my logs)
But in your case it look like: Network Host: ts0:513 Network Type: TCP/IP
I am not sure about these differences.
~cnanda
On Sun, Jan 31, 2010 at 8:43 PM, Wolfgang Denk wd@denx.de wrote:
Dear Chetan Nanda,
In message 7f245da81001310646x12451ac8s5ac9bda0fd6ac37c@mail.gmail.com you wrote:
Tried with loady command in u-boot and ymodem option from minicom. With this combination I am able to transfer and run uImage.
I tested this again on OMAP3 systems (including Beagle):
OMAP3 beagleboard.org # loadb ${uimage_addr} ## Ready for binary (kermit) download to 0x80300000 at 115200 bps...
(Back at pollux.denx.de)
Kermit>send /bin /tftpboot/beagle/uImage ... C-Kermit 8.0.211, 10 Apr 2004, pollux.denx.de [192.168.1.1]
Current Directory: /home/wd Network Host: ts0:513 Network Type: TCP/IP Parity: none RTT/Timeout: 01 / 02 SENDING: /tftpboot/beagle/uImage => uImage File Type: BINARY File Size: 1962820 Percent Done: 99 /////////////////////////////////////////////////- ...10...20...30...40...50...60...70...80...90..100 Estimated Time Left: 00:00:02 Transfer Rate, CPS: 4748 Window Slots: 1 of 1 Packet Type: D Packet Count: 2459 Packet Length: 1000 Error Count: 0 Last Error: Last Message:
X to cancel file, Z to cancel group, <CR> to resend last packet, E to send Error packet, ^C to quit immediately, ^L to refresh screen. ... Kermit>c Connecting to host ts0:513 Escape character: Ctrl-\ (ASCII 28, FS): enabled Type the escape character followed by C to get back, or followed by ? to see other options.
## Total Size = 0x001df344 = 1962820 Bytes ## Start Addr = 0x80300000 OMAP3 beagleboard.org # imi 0x80300000
## Checking Image at 80300000 ... Legacy image found Image Name: Linux-2.6.33-rc5-07168-gc48807a Created: 2010-01-25 14:58:56 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1962756 Bytes = 1.9 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OMAP3 beagleboard.org #
As you can see, this is working without any problems.
So either your host systems is still misconfigured (which I consoder most likely), or your target system hast issues (instable RAM and.or serial port, etc.), or you have been doing something wrong.
I don't think there is a problem in the mainline U-Boot code.
Best regards,
Wolfgang Denk
-- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd@denx.de If I can have honesty, it's easier to overlook mistakes. -- Kirk, "Space Seed", stardate 3141.9