Use EHCI MXC configuration options for i.MX25.
Signed-off-by: Benoît Thébaudeau benoit.thebaudeau@advansee.com Cc: Marek Vasut marex@denx.de Cc: Stefano Babic sbabic@denx.de Cc: Matthias Weisser weisserm@arcor.de --- .../drivers/usb/host/ehci-mxc.c | 71 +++++++++++++++++--- .../include/configs/zmx25.h | 6 +- 2 files changed, 66 insertions(+), 11 deletions(-)
diff --git u-boot-usb-76454b2.orig/drivers/usb/host/ehci-mxc.c u-boot-usb-76454b2/drivers/usb/host/ehci-mxc.c index e21f2c5..711c4a7 100644 --- u-boot-usb-76454b2.orig/drivers/usb/host/ehci-mxc.c +++ u-boot-usb-76454b2/drivers/usb/host/ehci-mxc.c @@ -28,10 +28,21 @@
#define USBCTRL_OTGBASE_OFFSET 0x600
-#define MX25_USB_CTRL_IP_PUE_DOWN_BIT (1<<6) -#define MX25_USB_CTRL_HSTD_BIT (1<<5) -#define MX25_USB_CTRL_USBTE_BIT (1<<4) -#define MX25_USB_CTRL_OCPOL_OTG_BIT (1<<3) +#define MX25_OTG_SIC_SHIFT 29 +#define MX25_OTG_SIC_MASK (0x3 << MX25_OTG_SIC_SHIFT) +#define MX25_OTG_PM_BIT (1 << 24) +#define MX25_OTG_PP_BIT (1 << 11) +#define MX25_OTG_OCPOL_BIT (1 << 3) + +#define MX25_H1_SIC_SHIFT 21 +#define MX25_H1_SIC_MASK (0x3 << MX25_H1_SIC_SHIFT) +#define MX25_H1_PP_BIT (1 << 18) +#define MX25_H1_PM_BIT (1 << 8) +#define MX25_H1_IPPUE_UP_BIT (1 << 7) +#define MX25_H1_IPPUE_DOWN_BIT (1 << 6) +#define MX25_H1_TLL_BIT (1 << 5) +#define MX25_H1_USBTE_BIT (1 << 4) +#define MX25_H1_OCPOL_BIT (1 << 2)
#define MX31_OTG_SIC_SHIFT 29 #define MX31_OTG_SIC_MASK (0x3 << MX31_OTG_SIC_SHIFT) @@ -51,12 +62,56 @@ static int mxc_set_usbcontrol(int port, unsigned int flags) { unsigned int v;
-#if defined(CONFIG_MX25) - v = MX25_USB_CTRL_IP_PUE_DOWN_BIT | MX25_USB_CTRL_HSTD_BIT | - MX25_USB_CTRL_USBTE_BIT | MX25_USB_CTRL_OCPOL_OTG_BIT; -#elif defined(CONFIG_MX31) v = readl(IMX_USB_BASE + USBCTRL_OTGBASE_OFFSET); +#if defined(CONFIG_MX25) + switch (port) { + case 0: /* OTG port */ + v &= ~(MX25_OTG_SIC_MASK | MX25_OTG_PM_BIT | MX25_OTG_PP_BIT | + MX25_OTG_OCPOL_BIT); + v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX25_OTG_SIC_SHIFT; + + if (!(flags & MXC_EHCI_POWER_PINS_ENABLED)) + v |= MX25_OTG_PM_BIT; + + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MX25_OTG_PP_BIT; + + if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)) + v |= MX25_OTG_OCPOL_BIT; + + break; + case 1: /* H1 port */ + v &= ~(MX25_H1_SIC_MASK | MX25_H1_PM_BIT | MX25_H1_PP_BIT | + MX25_H1_OCPOL_BIT | MX25_H1_TLL_BIT | MX25_H1_USBTE_BIT | + MX25_H1_IPPUE_DOWN_BIT | MX25_H1_IPPUE_UP_BIT); + v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX25_H1_SIC_SHIFT; + + if (!(flags & MXC_EHCI_POWER_PINS_ENABLED)) + v |= MX25_H1_PM_BIT; + + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MX25_H1_PP_BIT; + + if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)) + v |= MX25_H1_OCPOL_BIT; + + if (!(flags & MXC_EHCI_TTL_ENABLED)) + v |= MX25_H1_TLL_BIT; + + if (flags & MXC_EHCI_INTERNAL_PHY) + v |= MX25_H1_USBTE_BIT; + + if (flags & MXC_EHCI_IPPUE_DOWN) + v |= MX25_H1_IPPUE_DOWN_BIT;
+ if (flags & MXC_EHCI_IPPUE_UP) + v |= MX25_H1_IPPUE_UP_BIT; + + break; + default: + return -EINVAL; + } +#elif defined(CONFIG_MX31) switch (port) { case 0: /* OTG port */ v &= ~(MX31_OTG_SIC_MASK | MX31_OTG_PM_BIT); diff --git u-boot-usb-76454b2.orig/include/configs/zmx25.h u-boot-usb-76454b2/include/configs/zmx25.h index 447683a..e9216d9 100644 --- u-boot-usb-76454b2.orig/include/configs/zmx25.h +++ u-boot-usb-76454b2/include/configs/zmx25.h @@ -109,9 +109,9 @@ #define CONFIG_USB_EHCI /* Enable EHCI USB support */ #define CONFIG_USB_EHCI_MXC #define CONFIG_EHCI_HCD_INIT_AFTER_RESET -#define CONFIG_MXC_USB_PORT 2 -#define CONFIG_MXC_USB_PORTSC 0xC0000000 -#define CONFIG_MXC_USB_FLAGS 0 +#define CONFIG_MXC_USB_PORT 1 +#define CONFIG_MXC_USB_PORTSC MXC_EHCI_MODE_SERIAL +#define CONFIG_MXC_USB_FLAGS (MXC_EHCI_INTERNAL_PHY | MXC_EHCI_IPPUE_DOWN) #define CONFIG_EHCI_IS_TDI #define CONFIG_USB_STORAGE #define CONFIG_DOS_PARTITION