This commit add support for 96Boards Dragonboard410C. It is board based on APQ8016 Qualcomm SoC, complying with 96boards specification. Features (present out of the box): - 4x Cortex A53 (ARMv8) - 2x USB Host port - 1x USB Device port - 4x LEDs - 1x HDMI connector - 1x uSD connector - 3x buttons (Power, Vol+, Vol-/Reset) - WIFI, Bluetooth with integrated antenna - 8GiB eMMC
U-Boot boots chained with fastboot in 64-bit mode. For detailed build instructions see readme.txt in board directory.
Signed-off-by: Mateusz Kulikowski mateusz.kulikowski@gmail.com Tested-by: Simon Glass sjg@chromium.org ---
Changes in v3: - readme: Added info on how to enter fastboot mode and that dtbTool is also part of skales
Changes in v2: - Renamed CONFIG_DM_SPMI -> CONFIG_SPMI - Removed extra enter in dragonboard file - Added ULPI* to defconfig - Added MAINTAINERS to board - Cleaned up config file - use distro defaults/environment: - Dropped multiple CONFIG_CMD* and other CONFIG_* - Added distro env/config - Dropped old boot commands - Split dts - pm8916_gpio entries are taken directly from Linux Dragonboard dts; Add handles for u-boot in -uboot.dtsi; They will be removed once gpio drivers are converted to pinctrl. - Renamed some pmic nodes, fixed dragonboard.c to find them properly. - Added header and converted comments to c98-style in head.S - Print error if pmic gpio node is not found.
Changes in v1: - Add better help for dragonboard - Move static structures to board_prepare_usb - Add DM_SPMI to defconfig
arch/arm/dts/Makefile | 2 + arch/arm/dts/dragonboard410c-uboot.dtsi | 28 +++++ arch/arm/dts/dragonboard410c.dts | 148 ++++++++++++++++++++++ arch/arm/mach-snapdragon/Kconfig | 20 +++ board/qualcomm/dragonboard410c/Kconfig | 15 +++ board/qualcomm/dragonboard410c/MAINTAINERS | 6 + board/qualcomm/dragonboard410c/Makefile | 8 ++ board/qualcomm/dragonboard410c/dragonboard410c.c | 131 +++++++++++++++++++ board/qualcomm/dragonboard410c/head.S | 28 +++++ board/qualcomm/dragonboard410c/readme.txt | 43 +++++++ board/qualcomm/dragonboard410c/u-boot.lds | 90 +++++++++++++ configs/dragonboard410c_defconfig | 31 +++++ include/configs/dragonboard410c.h | 153 +++++++++++++++++++++++ 13 files changed, 703 insertions(+) create mode 100644 arch/arm/dts/dragonboard410c-uboot.dtsi create mode 100644 arch/arm/dts/dragonboard410c.dts create mode 100644 board/qualcomm/dragonboard410c/Kconfig create mode 100644 board/qualcomm/dragonboard410c/MAINTAINERS create mode 100644 board/qualcomm/dragonboard410c/Makefile create mode 100644 board/qualcomm/dragonboard410c/dragonboard410c.c create mode 100644 board/qualcomm/dragonboard410c/head.S create mode 100644 board/qualcomm/dragonboard410c/readme.txt create mode 100644 board/qualcomm/dragonboard410c/u-boot.lds create mode 100644 configs/dragonboard410c_defconfig create mode 100644 include/configs/dragonboard410c.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 0fa5796..ee584de 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -102,6 +102,8 @@ dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \ fsl-ls1043a-qds-lpuart.dtb \ fsl-ls1043a-rdb.dtb
+dtb-$(CONFIG_ARCH_SNAPDRAGON) += dragonboard410c.dtb + dtb-$(CONFIG_MACH_SUN4I) += \ sun4i-a10-a1000.dtb \ sun4i-a10-ba10-tvbox.dtb \ diff --git a/arch/arm/dts/dragonboard410c-uboot.dtsi b/arch/arm/dts/dragonboard410c-uboot.dtsi new file mode 100644 index 0000000..cc2c175 --- /dev/null +++ b/arch/arm/dts/dragonboard410c-uboot.dtsi @@ -0,0 +1,28 @@ +/* + * U-Boot addition to handle Dragonboard 410c pins + * + * (C) Copyright 2015 Mateusz Kulikowski mateusz.kulikowski@gmail.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +&pm8916_gpios { + usb_hub_reset_pm { + gpios = <&pm8916_gpios 2 0>; + }; + + usb_sw_sel_pm { + gpios = <&pm8916_gpios 3 0>; + }; +}; + + +&pm8916_pon { + key_vol_down { + gpios = <&pm8916_pon 1 0>; + }; + + key_power { + gpios = <&pm8916_pon 0 0>; + }; +}; diff --git a/arch/arm/dts/dragonboard410c.dts b/arch/arm/dts/dragonboard410c.dts new file mode 100644 index 0000000..7746622 --- /dev/null +++ b/arch/arm/dts/dragonboard410c.dts @@ -0,0 +1,148 @@ +/* + * Qualcomm APQ8016 based Dragonboard 410C board device tree source + * + * (C) Copyright 2015 Mateusz Kulikowski mateusz.kulikowski@gmail.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/dts-v1/; + +#include "skeleton64.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. Dragonboard 410c"; + compatible = "qcom,dragonboard", "qcom,apq8016-sbc"; + qcom,msm-id = <0xce 0x0 0xf8 0x0 0xf9 0x0 0xfa 0x0 0xf7 0x0>; + qcom,board-id = <0x10018 0x0>; + #address-cells = <0x2>; + #size-cells = <0x2>; + + memory { + device_type = "memory"; + reg = <0 0x80000000 0 0x3da00000>; + }; + + chosen { + stdout-path = "/soc/serial@78b0000"; + }; + + + soc { + #address-cells = <0x1>; + #size-cells = <0x1>; + ranges = <0x0 0x0 0x0 0xffffffff>; + compatible = "simple-bus"; + + clkc: qcom,gcc@1800000 { + compatible = "qcom,gcc-apq8016"; + reg = <0x1800000 0x80000>; + #address-cells = <0x1>; + #size-cells = <0x0>; + }; + + serial@78b0000 { + compatible = "qcom,msm-uartdm-v1.4"; + reg = <0x78b0000 0x200>; + u-boot,dm-pre-reloc; + clock = <&clkc 4>; + }; + + restart@4ab000 { + compatible = "qcom,pshold"; + reg = <0x4ab000 0x4>; + }; + + soc_gpios: pinctrl@1000000 { + compatible = "qcom,apq8016-pinctrl"; + reg = <0x1000000 0x300000>; + gpio-controller; + gpio-count = <122>; + gpio-bank-name="soc"; + #gpio-cells = <1>; + }; + + ehci@78d9000 { + compatible = "qcom,ehci-host"; + reg = <0x78d9000 0x400>; + }; + + sdhci@07824000 { + compatible = "qcom,sdhci-msm-v4"; + reg = <0x7824900 0x11c 0x7824000 0x800>; + bus-width = <0x8>; + index = <0x0>; + non-removable; + clock = <&clkc 0>; + clock-frequency = <100000000>; + }; + + sdhci@07864000 { + compatible = "qcom,sdhci-msm-v4"; + reg = <0x7864900 0x11c 0x7864000 0x800>; + index = <0x1>; + bus-width = <0x4>; + clock = <&clkc 1>; + clock-frequency = <200000000>; + }; + + spmi@200f000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x200f800 0x200 0x2400000 0x400000 0x2c00000 0x400000>; + #address-cells = <0x1>; + #size-cells = <0x1>; + pmic0: pm8916@0 { + compatible = "qcom,spmi-pmic"; + reg = <0x0 0x1>; + #address-cells = <0x1>; + #size-cells = <0x1>; + + pm8916_pon: pm8916_pon@800 { + compatible = "qcom,pm8916-pwrkey"; + reg = <0x800 0x96>; + #gpio-cells = <2>; + gpio-controller; + }; + + pm8916_gpios: pm8916_gpios@c000 { + compatible = "qcom,pm8916-gpio"; + reg = <0xc000 0x400>; + gpio-controller; + gpio-count = <4>; + #gpio-cells = <2>; + gpio-bank-name="pmic"; + }; + }; + + pmic1: pm8916@1 { + compatible = "qcom,spmi-pmic"; + reg = <0x1 0x1>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + user1 { + label = "green:user1"; + gpios = <&soc_gpios 21 0>; + }; + + user2 { + label = "green:user2"; + gpios = <&soc_gpios 120 0>; + }; + + user3 { + label = "green:user3"; + gpios = <&pm8916_gpios 0 0>; + }; + + user4 { + label = "green:user4"; + gpios = <&pm8916_gpios 1 0>; + }; + }; +}; + +#include "dragonboard410c-uboot.dtsi" diff --git a/arch/arm/mach-snapdragon/Kconfig b/arch/arm/mach-snapdragon/Kconfig index 156e733..dc7ba21 100644 --- a/arch/arm/mach-snapdragon/Kconfig +++ b/arch/arm/mach-snapdragon/Kconfig @@ -3,4 +3,24 @@ if ARCH_SNAPDRAGON config SYS_SOC default "snapdragon"
+choice + prompt "Snapdragon board select" + +config TARGET_DRAGONBOARD410C + bool "96Boards Dragonboard 410C" + help + Support for 96Boards Dragonboard 410C. This board complies with + 96Board Open Platform Specifications. Features: + - Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306) + - 1GiB RAM + - 8GiB eMMC, uSD slot + - WiFi, Bluetooth and GPS module + - 2x Host, 1x Device USB port + - HDMI + - 20-pin low speed and 40-pin high speed expanders, 4 LED, 3 buttons + +endchoice + +source "board/qualcomm/dragonboard410c/Kconfig" + endif diff --git a/board/qualcomm/dragonboard410c/Kconfig b/board/qualcomm/dragonboard410c/Kconfig new file mode 100644 index 0000000..03bd7ae --- /dev/null +++ b/board/qualcomm/dragonboard410c/Kconfig @@ -0,0 +1,15 @@ +if TARGET_DRAGONBOARD410C + +config SYS_BOARD + default "dragonboard410c" + +config SYS_VENDOR + default "qualcomm" + +config SYS_SOC + default "apq8016" + +config SYS_CONFIG_NAME + default "dragonboard410c" + +endif diff --git a/board/qualcomm/dragonboard410c/MAINTAINERS b/board/qualcomm/dragonboard410c/MAINTAINERS new file mode 100644 index 0000000..65cb47c --- /dev/null +++ b/board/qualcomm/dragonboard410c/MAINTAINERS @@ -0,0 +1,6 @@ +DRAGONBOARD410C BOARD +M: Mateusz Kulikowski mateusz.kulikowski@gmail.com +S: Maintained +F: board/qualcomm/dragonboard410c/ +F: include/configs/dragonboard410c.h +F: configs/dragonboard410c_defconfig diff --git a/board/qualcomm/dragonboard410c/Makefile b/board/qualcomm/dragonboard410c/Makefile new file mode 100644 index 0000000..cd67808 --- /dev/null +++ b/board/qualcomm/dragonboard410c/Makefile @@ -0,0 +1,8 @@ +# +# (C) Copyright 2015 Mateusz Kulikowski mateusz.kulikowski@gmail.com +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := dragonboard410c.o +extra-y += head.o diff --git a/board/qualcomm/dragonboard410c/dragonboard410c.c b/board/qualcomm/dragonboard410c/dragonboard410c.c new file mode 100644 index 0000000..1fa5664 --- /dev/null +++ b/board/qualcomm/dragonboard410c/dragonboard410c.c @@ -0,0 +1,131 @@ +/* + * Board init file for Dragonboard 410C + * + * (C) Copyright 2015 Mateusz Kulikowski mateusz.kulikowski@gmail.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <dm.h> +#include <usb.h> +#include <asm/gpio.h> + +DECLARE_GLOBAL_DATA_PTR; + +int dram_init(void) +{ + gd->ram_size = PHYS_SDRAM_1_SIZE; + return 0; +} + +void dram_init_banksize(void) +{ + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; +} + + +int board_prepare_usb(enum usb_init_type type) +{ + static struct udevice *pmic_gpio; + static struct gpio_desc hub_reset, usb_sel; + int ret = 0, node; + + if (!pmic_gpio) { + ret = uclass_get_device_by_name(UCLASS_GPIO, + "pm8916_gpios@c000", + &pmic_gpio); + if (ret < 0) { + printf("Failed to find pm8916_gpios@c000 node.\n"); + return ret; + } + } + + /* Try to request gpios needed to start usb host on dragonboard */ + if (!dm_gpio_is_valid(&hub_reset)) { + node = fdt_subnode_offset(gd->fdt_blob, pmic_gpio->of_offset, + "usb_hub_reset_pm"); + if (node < 0) { + printf("Failed to find usb_hub_reset_pm dt node.\n"); + return node; + } + ret = gpio_request_by_name_nodev(gd->fdt_blob, node, "gpios", 0, + &hub_reset, 0); + if (ret < 0) { + printf("Failed to request usb_hub_reset_pm gpio.\n"); + return ret; + } + } + + if (!dm_gpio_is_valid(&usb_sel)) { + node = fdt_subnode_offset(gd->fdt_blob, pmic_gpio->of_offset, + "usb_sw_sel_pm"); + if (node < 0) { + printf("Failed to find usb_sw_sel_pm dt node.\n"); + return 0; + } + ret = gpio_request_by_name_nodev(gd->fdt_blob, node, "gpios", 0, + &usb_sel, 0); + if (ret < 0) { + printf("Failed to request usb_sw_sel_pm gpio.\n"); + return ret; + } + } + + if (type == USB_INIT_HOST) { + /* Start USB Hub */ + dm_gpio_set_dir_flags(&hub_reset, + GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE); + mdelay(100); + /* Switch usb to host connectors */ + dm_gpio_set_dir_flags(&usb_sel, + GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE); + mdelay(100); + } else { /* Device */ + /* Disable hub */ + dm_gpio_set_dir_flags(&hub_reset, GPIOD_IS_OUT); + /* Switch back to device connector */ + dm_gpio_set_dir_flags(&usb_sel, GPIOD_IS_OUT); + } + + return 0; +} + +int board_init(void) +{ + return 0; +} + +/* Check for vol- button - if pressed - stop autoboot */ +int misc_init_r(void) +{ + struct udevice *pon; + struct gpio_desc resin; + int node, ret; + + ret = uclass_get_device_by_name(UCLASS_GPIO, "pm8916_pon@800", &pon); + if (ret < 0) { + printf("Failed to find PMIC pon node. Check device tree\n"); + return 0; + } + + node = fdt_subnode_offset(gd->fdt_blob, pon->of_offset, "key_vol_down"); + if (node < 0) { + printf("Failed to find key_vol_down node. Check device tree\n"); + return 0; + } + + if (gpio_request_by_name_nodev(gd->fdt_blob, node, "gpios", 0, &resin, + 0)) { + printf("Failed to request key_vol_down button.\n"); + return 0; + } + + if (dm_gpio_get_value(&resin)) { + setenv("bootdelay", "-1"); + printf("Power button pressed - dropping to console.\n"); + } + + return 0; +} diff --git a/board/qualcomm/dragonboard410c/head.S b/board/qualcomm/dragonboard410c/head.S new file mode 100644 index 0000000..9f1e0d9 --- /dev/null +++ b/board/qualcomm/dragonboard410c/head.S @@ -0,0 +1,28 @@ +/* + * Little-Kernel/Fastboot header for proper chain-loading + * + * (C) Copyright 2015 Mateusz Kulikowski mateusz.kulikowski@gmail.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <config.h> + +.global _fastboot_header +_fastboot_header: + b _start + add x13, x18, #0x16 + /* Image load offset from start of RAM, little-endian */ + .quad CONFIG_SYS_TEXT_BASE-PHYS_SDRAM_1 + /* Effective size of kernel image, little-endian */ + .quad 0 /* 0x60000 */ + /* Informative flags, little-endian */ + .quad 0 + .quad 0 /* reserved */ + .quad 0 /* reserved */ + .quad 0 /* reserved */ + .byte 0x41 /* Magic number, "ARM\x64" */ + .byte 0x52 + .byte 0x4d + .byte 0x64 + .word 0 /* reserved */ diff --git a/board/qualcomm/dragonboard410c/readme.txt b/board/qualcomm/dragonboard410c/readme.txt new file mode 100644 index 0000000..a05a071 --- /dev/null +++ b/board/qualcomm/dragonboard410c/readme.txt @@ -0,0 +1,43 @@ +# +# (C) Copyright 2015 Mateusz Kulikowski mateusz.kulikowski@gmail.com +# +# SPDX-License-Identifier: GPL-2.0+ +# + +Build & Run instructions: + +1) Install mkbootimg and dtbTool from + git://codeaurora.org/quic/kernel/skales (15ece94f09 worked for me) +2) Setup CROSS_COMPILE to aarch64 compiler +3) make dragonboard410c_config +4) make +5) generate fake, empty ramdisk (can have 0 bytes) +$ touch rd + +6) generate qualcomm device tree, use dtbTool to generate it +$ dtbTool -o dt.img arch/arm/dts + +7) generate image with mkbootimg: +$ mkbootimg --kernel=u-boot-dtb.bin --output=u-boot.img --dt=dt.img --pagesize 2048 --base 0x80000000 --ramdisk=rd --cmdline="" + +8) Enter fastboot (reboot board with vol- button pressed) + +9) Boot it: +$ fastboot boot u-boot.img +or flash as kernel: +$ fastboot flash boot u-boot.img +$ fastboot reboot + + +What is working: +- UART +- GPIO (SoC) +- SD +- eMMC +- Reset +- USB in EHCI mode (usb starts does switch device->host, usb stop does the opposite) +- PMIC GPIOS (but not in generic subsystem) +- PMIC "special" buttons (power, vol-) + +What is not working / known bugs: +- SDHCI is slow (~2.5MiB/s for SD and eMMC) diff --git a/board/qualcomm/dragonboard410c/u-boot.lds b/board/qualcomm/dragonboard410c/u-boot.lds new file mode 100644 index 0000000..3fb4235 --- /dev/null +++ b/board/qualcomm/dragonboard410c/u-boot.lds @@ -0,0 +1,90 @@ +/* + * Override linker script for fastboot-readable images + * + * (C) Copyright 2015 Mateusz Kulikowski mateusz.kulikowski@gmail.com + * + * Based on arch/arm/cpu/armv8/u-boot.lds (Just add header) + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +OUTPUT_FORMAT("elf64-littleaarch64", "elf64-littleaarch64", "elf64-littleaarch64") +OUTPUT_ARCH(aarch64) +ENTRY(_fastboot_header) +SECTIONS +{ + . = 0x00000000; + + . = ALIGN(8); + .text : + { + *(.__image_copy_start) + board/qualcomm/dragonboard410c/head.o (.text*) + CPUDIR/start.o (.text*) + *(.text*) + } + + . = ALIGN(8); + .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) } + + . = ALIGN(8); + .data : { + *(.data*) + } + + . = ALIGN(8); + + . = .; + + . = ALIGN(8); + .u_boot_list : { + KEEP(*(SORT(.u_boot_list*))); + } + + . = ALIGN(8); + + .image_copy_end : + { + *(.__image_copy_end) + } + + . = ALIGN(8); + + .rel_dyn_start : + { + *(.__rel_dyn_start) + } + + .rela.dyn : { + *(.rela*) + } + + .rel_dyn_end : + { + *(.__rel_dyn_end) + } + + _end = .; + + . = ALIGN(8); + + .bss_start : { + KEEP(*(.__bss_start)); + } + + .bss : { + *(.bss*) + . = ALIGN(8); + } + + .bss_end : { + KEEP(*(.__bss_end)); + } + + /DISCARD/ : { *(.dynsym) } + /DISCARD/ : { *(.dynstr*) } + /DISCARD/ : { *(.dynamic*) } + /DISCARD/ : { *(.plt*) } + /DISCARD/ : { *(.interp*) } + /DISCARD/ : { *(.gnu*) } +} diff --git a/configs/dragonboard410c_defconfig b/configs/dragonboard410c_defconfig new file mode 100644 index 0000000..84fe597 --- /dev/null +++ b/configs/dragonboard410c_defconfig @@ -0,0 +1,31 @@ +CONFIG_ARM=y +CONFIG_ARM64=y +CONFIG_ARCH_SNAPDRAGON=y +CONFIG_TARGET_DRAGONBOARD410C=y + +CONFIG_SYS_PROMPT="dragonboard410c => " +CONFIG_CMD_USB=y +# CONFIG_CMD_IMI is not set +# CONFIG_CMD_IMLS is not set +CONFIG_DEFAULT_DEVICE_TREE="dragonboard410c" + +CONFIG_CLK=y +CONFIG_MSM_GPIO=y +CONFIG_PM8916_GPIO=y +CONFIG_LED=y +CONFIG_LED_GPIO=y +CONFIG_RESET=y +CONFIG_DM_MMC=y +CONFIG_MSM_SDHCI=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_PM8916=y +CONFIG_SPMI=y +CONFIG_SPMI_MSM=y +CONFIG_MSM_SERIAL=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_MSM=y +CONFIG_USB_ULPI=y +CONFIG_USB_ULPI_VIEWPORT=y +CONFIG_USB_STORAGE=y diff --git a/include/configs/dragonboard410c.h b/include/configs/dragonboard410c.h new file mode 100644 index 0000000..1dfb171 --- /dev/null +++ b/include/configs/dragonboard410c.h @@ -0,0 +1,153 @@ +/* + * Board configuration file for Dragonboard 410C + * + * (C) Copyright 2015 Mateusz Kulikowski mateusz.kulikowski@gmail.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIGS_DRAGONBOARD410C_H +#define __CONFIGS_DRAGONBOARD410C_H + +#include <linux/sizes.h> +#include <asm/arch/sysmap-apq8016.h> + +#define CONFIG_IDENT_STRING "\nQualcomm-DragonBoard 410C" + +#define CONFIG_MISC_INIT_R /* To stop autoboot */ + +/* Flat Device Tree Definitions */ +#define CONFIG_OF_LIBFDT + +/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM_1 0x80000000 +/* 1008 MB (the last ~30Mb are secured for TrustZone by ATF*/ +#define PHYS_SDRAM_1_SIZE 0x3da00000 +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_TEXT_BASE 0x80080000 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0) +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x80000) +#define CONFIG_SYS_BOOTM_LEN 0x1000000 /* 16MB max kernel size */ + +/* UART */ +#define CONFIG_BAUDRATE 115200 + +/* Generic Timer Definitions */ +#define COUNTER_FREQUENCY 19000000 + +/* This are needed to have proper mmc support */ +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_SDHCI + +#define CONFIG_SYS_LDSCRIPT "board/qualcomm/dragonboard410c/u-boot.lds" + +/* Fixup - in init code we switch from device to host mode, + * it has to be done after each HCD reset */ +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET + +#define CONFIG_USB_HOST_ETHER /* Enable USB Networking */ + +/* Support all possible USB ethernet dongles */ +#define CONFIG_USB_ETHER_DM9601 +#define CONFIG_USB_ETHER_ASIX +#define CONFIG_USB_ETHER_ASIX88179 +#define CONFIG_USB_ETHER_MCS7830 +#define CONFIG_USB_ETHER_SMSC95XX + +/* Libraries */ +#define CONFIG_MD5 + +/* Extra Commands */ +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_ENV +#define CONFIG_CMD_GPIO +#define CONFIG_CMD_GPT +#define CONFIG_CMD_MD5SUM +#define CONFIG_CMD_MEMINFO +#define CONFIG_CMD_MMC +/* Enable that for switching of boot partitions */ +/* Disabled by default as some sub-commands can brick eMMC */ +/*#define CONFIG_SUPPORT_EMMC_BOOT */ +#define CONFIG_CMD_PART +#define CONFIG_CMD_REGINFO /* Register dump */ +#define CONFIG_CMD_TFTP +#define CONFIG_CMD_TIMER +#define CONFIG_CMD_UNZIP + +/* Partition table support */ +#define HAVE_BLOCK_DEVICE /* Needed for partition commands */ +#define CONFIG_PARTITION_UUIDS + +#include <config_distro_defaults.h> + +/* BOOTP options */ +#define CONFIG_BOOTP_BOOTFILESIZE + +/* Environment - Boot*/ +#define CONFIG_BOOTARGS "console=ttyMSM0,115200n8" + +#define BOOT_TARGET_DEVICES(func) \ + func(USB, usb, 0) \ + func(MMC, mmc, 0) \ + func(MMC, mmc, 1) \ + func(DHCP, dhcp, na) + +#include <config_distro_bootcmd.h> + +/* Does what recovery does */ +#define REFLASH(file, part) \ +"part start mmc 0 "#part" start && "\ +"part size mmc 0 "#part" size && "\ +"tftp $loadaddr "#file" && " \ +"mmc write $loadaddr $start $size && " + + +#define CONFIG_ENV_REFLASH \ +"mmc dev 0 && "\ +"usb start && "\ +"dhcp && "\ +"tftp $loadaddr dragonboard/rescue/gpt_both0.bin && "\ +"mmc write $loadaddr 0 43 && " \ +"mmc rescan && "\ +REFLASH(dragonboard/rescue/NON-HLOS.bin, 1)\ +REFLASH(dragonboard/rescue/sbl1.mbn, 2)\ +REFLASH(dragonboard/rescue/rpm.mbn, 3)\ +REFLASH(dragonboard/rescue/tz.mbn, 4)\ +REFLASH(dragonboard/rescue/hyp.mbn, 5)\ +REFLASH(dragonboard/rescue/sec.dat, 6)\ +REFLASH(dragonboard/rescue/emmc_appsboot.mbn, 7)\ +REFLASH(dragonboard/u-boot.img, 8)\ +"usb stop &&"\ +"echo Reflash completed" + +/* Environment */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "reflash="CONFIG_ENV_REFLASH"\0"\ + "loadaddr=0x81000000\0" \ + "fdt_high=0xffffffffffffffff\0" \ + "initrd_high=0xffffffffffffffff\0" \ + "linux_image=Image\0" \ + "linux_addr=0x81000000\0"\ + "fdt_image=apq8016-sbc.dtb\0" \ + "fdt_addr=0x83000000\0"\ + "ramdisk_addr=0x84000000\0"\ + BOOTENV + +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_SIZE 0x1000 +#define CONFIG_ENV_VARS_UBOOT_CONFIG +#define CONFIG_SYS_NO_FLASH + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_8M) + +/* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_MAXARGS 64 /* max command args */ + +#endif