From: Camelia Groza camelia.groza@nxp.com
Both DM_ETH and DM_PCI are enabled for the T2080RDB board. Remove the board_eth_init() callback and the non-DM_ETH code paths since they are not needed anymore.
Signed-off-by: Camelia Groza camelia.groza@nxp.com --- Changes in v2: - new patch
board/freescale/t208xrdb/eth_t208xrdb.c | 79 ------------------------- board/freescale/t208xrdb/t208xrdb.c | 4 -- 2 files changed, 83 deletions(-)
diff --git a/board/freescale/t208xrdb/eth_t208xrdb.c b/board/freescale/t208xrdb/eth_t208xrdb.c index b0ff4b1f375a..4b44b1617d6c 100644 --- a/board/freescale/t208xrdb/eth_t208xrdb.c +++ b/board/freescale/t208xrdb/eth_t208xrdb.c @@ -26,85 +26,6 @@ #include <fsl_dtsec.h> #include <asm/fsl_serdes.h>
-int board_eth_init(struct bd_info *bis) -{ -#if defined(CONFIG_FMAN_ENET) - int i, interface; - struct memac_mdio_info dtsec_mdio_info; - struct memac_mdio_info tgec_mdio_info; - struct mii_dev *dev; - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 srds_s1; - - srds_s1 = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS1_PRTCL; - srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; - - dtsec_mdio_info.regs = - (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR; - - dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; - - /* Register the 1G MDIO bus */ - fm_memac_mdio_init(bis, &dtsec_mdio_info); - - tgec_mdio_info.regs = - (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR; - tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME; - - /* Register the 10G MDIO bus */ - fm_memac_mdio_init(bis, &tgec_mdio_info); - - /* Set the two on-board RGMII PHY address */ - fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY1_ADDR); - fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY2_ADDR); - - switch (srds_s1) { - case 0x66: - case 0x6b: - fm_info_set_phy_address(FM1_10GEC1, CORTINA_PHY_ADDR1); - fm_info_set_phy_address(FM1_10GEC2, CORTINA_PHY_ADDR2); - fm_info_set_phy_address(FM1_10GEC3, FM1_10GEC3_PHY_ADDR); - fm_info_set_phy_address(FM1_10GEC4, FM1_10GEC4_PHY_ADDR); - break; - default: - printf("SerDes1 protocol 0x%x is not supported on T208xRDB\n", - srds_s1); - break; - } - - for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { - interface = fm_info_get_enet_if(i); - switch (interface) { - case PHY_INTERFACE_MODE_RGMII: - case PHY_INTERFACE_MODE_RGMII_TXID: - case PHY_INTERFACE_MODE_RGMII_RXID: - case PHY_INTERFACE_MODE_RGMII_ID: - dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME); - fm_info_set_mdio(i, dev); - break; - default: - break; - } - } - - for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) { - switch (fm_info_get_enet_if(i)) { - case PHY_INTERFACE_MODE_XGMII: - dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME); - fm_info_set_mdio(i, dev); - break; - default: - break; - } - } - - cpu_eth_init(bis); -#endif /* CONFIG_FMAN_ENET */ - - return pci_eth_init(bis); -} - /* Disable the MAC5 and MAC6 "fsl,fman-memac" nodes and the two * "fsl,dpa-ethernet" nodes that reference them. */ diff --git a/board/freescale/t208xrdb/t208xrdb.c b/board/freescale/t208xrdb/t208xrdb.c index 7ccb205c6473..35f5dff46645 100644 --- a/board/freescale/t208xrdb/t208xrdb.c +++ b/board/freescale/t208xrdb/t208xrdb.c @@ -136,11 +136,7 @@ int ft_board_setup(void *blob, struct bd_info *bd) fsl_fdt_fixup_dr_usb(blob, bd);
#ifdef CONFIG_SYS_DPAA_FMAN -#ifndef CONFIG_DM_ETH - fdt_fixup_fman_ethernet(blob); -#else fdt_fixup_board_fman_ethernet(blob); -#endif fdt_fixup_board_enet(blob); #endif
-- 2.17.1