14.09.2020 21:50, Tom Rini wrote:
On Mon, Sep 14, 2020 at 08:08:48PM +0300, Denis Pynkin wrote:
14.09.2020 17:11, Tom Rini wrote:
On Mon, Sep 14, 2020 at 09:29:18AM -0400, Tom Rini wrote:
On Mon, Sep 14, 2020 at 04:20:20PM +0300, Denis Pynkin wrote:
14.09.2020 15:33, Tom Rini wroteт:
On Mon, Sep 14, 2020 at 08:03:33AM -0300, Fabio Estevam wrote:
>> The size of the binary created with the default U-boot config is much >> greater than the default offset for environment `0x60000`. If the new >> version is flashed onto SPI it overlaps with the stored environment. >> This leads to U-Boot corruption in case of saving environment onto >> SPI and non-bootable SabreLite board. >> >> Signed-off-by: Denis Pynkin denis.pynkin@collabora.com > > Reviewed-by: Fabio Estevam festevam@gmail.com > > In case you want to detect errors like this again in the future, you could add > CONFIG_BOARD_SIZE_LIMIT that detects such overlaps in build-time. > > Please check commit 033f6ea5fa5f ("mx53loco: Fix U-Boot corruption > after saving the environment") > > The addition of CONFIG_BOARD_SIZE_LIMIT can be a separate patch though.
Hold on. Can we shrink the board back down so that we don't need to move the environment? Moving the environment is bad as it will also break existing users. Thanks!
I don't think so to be honest. Current sizes even for `u-boot-nodtb.imx` in my builds are:
- 595308 (0x9156C) -- cross-compilation
- 470780 (0x72EFC) -- native build
I'd like to have one thread where we see what on earth is going on there. That's a rather crazy size difference and very troubling.
which is much larger than current offset 393216 (0x60000)
The offset for environment `CONFIG_ENV_OFFSET=0x60000` were added in commit a09fea1 just a year ago. Not sure if it was tested with SabreLite board tbh -- this is a bulk commit aimed for ARMv8 and sizes of binaries produced with pre-a09fea1 commit are also larger than the current offset.
Ah, so here's what's going on then. Commit a09fea1 wasn't about ARMv8, it was about migrating options to the defconfig files. In this case, it should have been set to the value you're changing it to now, at least from a read of the patch (include/configs/mx6sabre_common.h would set it to 0xC0000 if CONFIG_ENV_IS_IN_MMC), but I thought I had done that migration with my hack to make a tool that had the in-use value be printed. So I'm going to re-check that whole thing to see what else might be wrong as well. Thanks!
Ah, so, mx6qsabrelite falls in to the "nitrogen6x" family and not the rest of the "sabre" board families. As such, it's always had the env offset of 0x60000. Jumping back somewhat arbitrarily to v2014.10, I see with gcc-4.9 a size of 404480 on u-boot.imx which is still bigger.
The commit message isn't clear however, as environment is in MMC and not SPI, so SPI booting should be fine. But MMC/eMMC is where this case can happen (I'm not sure which device is SD slot and which is eMMC on this hardware off-hand). Thanks!
To my shame -- I didn't even thought about the booting from MMC, but yes -- should be the same issue in case if U-Boot is placed on SD-card.
This device have 2MB SPI NOR flash there the U-Boot could be flashed with an environment. We are using this approach, so I attempt to describe the issue from this point of view.
Should I try to re-word the description? Or may I ask you to add a better description?
Well, there's a few things going on here then. The defconfig has ENV_IS_IN_MMC, not ENV_IS_IN_SPI. So SPI booting should be fine we're putting U-Boot and environment on entirely different media. There's no conflict. Booting from the first MMC device can be broken as that's where we say the environment should be and 'saveenv' will scribble all over it. So can you confirm what the breaking condition you see is? The commit message talks about SPI, but SPI should work as-is.
You are absolutely right. My fault -- copy-paste the patch from my project as is without additional testing. Did an additional tests with default value 0x60000: - works well with the combination U-Boot on SPI NOR flash + environment on MMC - corrupted U-Boot on MMC after `saveenv` if used U-Boot on MMC - corrupted U-Boot after `saveenv` if it is configured with `CONFIG_ENV_IS_IN_SPI_FLASH=y` and flashed on SPI
The value `0xC0000` fixes the issue for both corrupted cases.
Thanks a lot for pointing to incorrect description and misunderstanding!