[PATCH 08/12] ARM: dts: sunxi: H2+/H3/H5: Sync from Linux v5.18-rc1

Copy the devicetree source for the H2+/H3/H5 SoCs and all existing boards from the Linux v5.18-rc1 tag.

To maintain ABI compatibility with existing LTS kernels, one change moving some IP blocks to the r_intc interrupt controller is excluded. This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.

This commit also adds the following new board devicetree: - sun8i-h3-nanopi-r1.dts

This update should not impact any existing U-Boot functionality.

Signed-off-by: Samuel Holland samuel@sholland.org ---

arch/arm/dts/Makefile | 1 + arch/arm/dts/sun50i-h5-cpu-opp.dtsi | 2 +- arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts | 9 +- arch/arm/dts/sun50i-h5.dtsi | 6 +- .../dts/sun8i-h2-plus-bananapi-m2-zero.dts | 28 ++- arch/arm/dts/sun8i-h3-beelink-x2.dts | 27 ++- arch/arm/dts/sun8i-h3-nanopi-neo-air.dts | 28 +++ arch/arm/dts/sun8i-h3-nanopi-r1.dts | 169 ++++++++++++++++++ arch/arm/dts/sun8i-h3-nanopi.dtsi | 1 + arch/arm/dts/sun8i-h3-orangepi-2.dts | 3 +- arch/arm/dts/sun8i-h3-orangepi-pc.dts | 3 +- arch/arm/dts/sun8i-h3.dtsi | 10 +- arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi | 18 +- arch/arm/dts/sunxi-bananapi-m2-plus.dtsi | 4 +- arch/arm/dts/sunxi-h3-h5.dtsi | 42 ++++- arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi | 13 ++ arch/arm/dts/sunxi-libretech-all-h3-it.dtsi | 2 +- 17 files changed, 342 insertions(+), 24 deletions(-) create mode 100644 arch/arm/dts/sun8i-h3-nanopi-r1.dts

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 6433f63455..bbd69d3a67 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -655,6 +655,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \ sun8i-h3-nanopi-m1-plus.dtb \ sun8i-h3-nanopi-neo.dtb \ sun8i-h3-nanopi-neo-air.dtb \ + sun8i-h3-nanopi-r1.dtb \ sun8i-h3-orangepi-2.dtb \ sun8i-h3-orangepi-lite.dtb \ sun8i-h3-orangepi-one.dtb \ diff --git a/arch/arm/dts/sun50i-h5-cpu-opp.dtsi b/arch/arm/dts/sun50i-h5-cpu-opp.dtsi index b265720195..1afad8b437 100644 --- a/arch/arm/dts/sun50i-h5-cpu-opp.dtsi +++ b/arch/arm/dts/sun50i-h5-cpu-opp.dtsi @@ -2,7 +2,7 @@ // Copyright (C) 2020 Chen-Yu Tsai wens@csie.org

/ { - cpu_opp_table: cpu-opp-table { + cpu_opp_table: opp-table-cpu { compatible = "operating-points-v2"; opp-shared;

diff --git a/arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts b/arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts index 55bcdf8d1a..55b369534a 100644 --- a/arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts +++ b/arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts @@ -142,9 +142,16 @@ status = "okay";

eeprom@51 { - compatible = "microchip,24c02"; + compatible = "microchip,24c02", "atmel,24c02"; reg = <0x51>; pagesize = <16>; + read-only; + #address-cells = <1>; + #size-cells = <1>; + + eth_mac1: mac-address@fa { + reg = <0xfa 0x06>; + }; }; };

diff --git a/arch/arm/dts/sun50i-h5.dtsi b/arch/arm/dts/sun50i-h5.dtsi index ab860e20d0..9b3462b13c 100644 --- a/arch/arm/dts/sun50i-h5.dtsi +++ b/arch/arm/dts/sun50i-h5.dtsi @@ -217,7 +217,7 @@ }; };

- gpu_thermal { + gpu-thermal { polling-delay-passive = <0>; polling-delay = <0>; thermal-sensors = <&ths 1>; @@ -233,6 +233,10 @@ compatible = "allwinner,sun50i-h5-de2-clk"; };

+&mbus { + compatible = "allwinner,sun50i-h5-mbus"; +}; + &mmc0 { compatible = "allwinner,sun50i-h5-mmc", "allwinner,sun50i-a64-mmc"; diff --git a/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts index f3f7a2c912..d5c7b7984d 100644 --- a/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts +++ b/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts @@ -26,6 +26,17 @@ stdout-path = "serial0:115200n8"; };

+ connector { + compatible = "hdmi-connector"; + type = "c"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + leds { compatible = "gpio-leds";

@@ -41,8 +52,9 @@

sw4 { label = "power"; - linux,code = <BTN_0>; + linux,code = <KEY_POWER>; gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; + wakeup-source; }; };

@@ -103,10 +115,24 @@ cpu-supply = <&reg_vdd_cpux>; };

+&de { + status = "okay"; +}; + &ehci0 { status = "okay"; };

+&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &mmc0 { vmmc-supply = <&reg_vcc3v3>; bus-width = <4>; diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts b/arch/arm/dts/sun8i-h3-beelink-x2.dts index 62b5280ec0..cd9f655e4f 100644 --- a/arch/arm/dts/sun8i-h3-beelink-x2.dts +++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts @@ -57,6 +57,12 @@ ethernet1 = &sdiowifi; };

+ cec-gpio { + compatible = "cec-gpio"; + cec-gpios = <&pio 0 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* PA14 */ + hdmi-phandle = <&hdmi>; + }; + chosen { stdout-path = "serial0:115200n8"; }; @@ -87,11 +93,15 @@ }; };

- wifi_pwrseq: wifi_pwrseq { - compatible = "mmc-pwrseq-simple"; - reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ - clocks = <&rtc 1>; - clock-names = "ext_clock"; + r-gpio-keys { + compatible = "gpio-keys"; + + power { + label = "power"; + linux,code = <KEY_POWER>; + gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; + wakeup-source; + }; };

sound_spdif { @@ -111,6 +121,13 @@ #sound-dai-cells = <0>; compatible = "linux,spdif-dit"; }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ + clocks = <&rtc 1>; + clock-names = "ext_clock"; + }; };

&de { diff --git a/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts index be49eabbff..cd3df12b65 100644 --- a/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts +++ b/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts @@ -103,12 +103,40 @@ }; };

+&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_8bit_pins>; + vmmc-supply = <&reg_vcc3v3>; + vqmmc-supply = <&reg_vcc3v3>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pa_pins>; status = "okay"; };

+&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>, <&uart3_rts_cts_pins>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + clocks = <&rtc 1>; + clock-names = "lpo"; + vbat-supply = <&reg_vcc3v3>; + vddio-supply = <&reg_vcc3v3>; + device-wakeup-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */ + host-wakeup-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */ + shutdown-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */ + }; +}; + &usbphy { /* USB VBUS is always on */ status = "okay"; diff --git a/arch/arm/dts/sun8i-h3-nanopi-r1.dts b/arch/arm/dts/sun8i-h3-nanopi-r1.dts new file mode 100644 index 0000000000..26e2e6172e --- /dev/null +++ b/arch/arm/dts/sun8i-h3-nanopi-r1.dts @@ -0,0 +1,169 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2019 Igor Pecovnik igor@armbian.com + * Copyright (C) 2020 Jayantajit Gogoi jayanta.gogoi525@gmail.com + * Copyright (C) 2020 Yu-Tung Chang mtwget@gmail.com +*/ + +#include "sun8i-h3-nanopi.dtsi" +#include <dt-bindings/leds/common.h> + +/ { + model = "FriendlyARM NanoPi R1"; + compatible = "friendlyarm,nanopi-r1", "allwinner,sun8i-h3"; + + aliases { + serial1 = &uart1; + ethernet0 = &emac; + ethernet1 = &wifi; + }; + + reg_gmac_3v3: gmac-3v3 { + compatible = "regulator-fixed"; + regulator-name = "gmac-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <100000>; + enable-active-high; + gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */ + }; + + reg_vdd_cpux: gpio-regulator { + compatible = "regulator-gpio"; + regulator-name = "vdd-cpux"; + regulator-type = "voltage"; + regulator-boot-on; + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-ramp-delay = <50>; + gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ + gpios-states = <0x1>; + states = <1100000 0x0>, + <1300000 0x1>; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ + clocks = <&rtc 1>; + clock-names = "ext_clock"; + }; + + leds { + led-2 { + function = LED_FUNCTION_WAN; + color = <LED_COLOR_ID_GREEN>; + gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */ + }; + + led-3 { + function = LED_FUNCTION_LAN; + color = <LED_COLOR_ID_GREEN>; + gpios = <&pio 0 9 GPIO_ACTIVE_HIGH>; /* PA9 */ + }; + }; +}; + +&cpu0 { + cpu-supply = <&reg_vdd_cpux>; +}; + +&ehci1 { + status = "okay"; +}; + +&ehci2 { + status = "okay"; +}; + +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_rgmii_pins>; + phy-supply = <&reg_gmac_3v3>; + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii-id"; + status = "okay"; +}; + +&external_mdio { + ext_rgmii_phy: ethernet-phy@7 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <7>; + }; +}; + +&mmc1 { + vmmc-supply = <&reg_vcc3v3>; + vqmmc-supply = <&reg_vcc3v3>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + wifi: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&pio>; + interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */ + interrupt-names = "host-wake"; + }; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_8bit_pins>; + vmmc-supply = <&reg_vcc3v3>; + vqmmc-supply = <&reg_vcc3v3>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&ohci2 { + status = "okay"; +}; + +&reg_usb0_vbus { + gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */ + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>, <&uart3_rts_cts_pins>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + clocks = <&rtc 1>; + clock-names = "lpo"; + vbat-supply = <&reg_vcc3v3>; + vddio-supply = <&reg_vcc3v3>; + device-wakeup-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */ + host-wakeup-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */ + shutdown-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */ + }; +}; + +&usb_otg { + status = "okay"; + dr_mode = "otg"; +}; + +&usbphy { + usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ + usb0_vbus-supply = <&reg_usb0_vbus>; + status = "okay"; +}; diff --git a/arch/arm/dts/sun8i-h3-nanopi.dtsi b/arch/arm/dts/sun8i-h3-nanopi.dtsi index c7c3e7d8b3..fc45d5aaa6 100644 --- a/arch/arm/dts/sun8i-h3-nanopi.dtsi +++ b/arch/arm/dts/sun8i-h3-nanopi.dtsi @@ -81,6 +81,7 @@ label = "k1"; linux,code = <KEY_POWER>; gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; + wakeup-source; }; }; }; diff --git a/arch/arm/dts/sun8i-h3-orangepi-2.dts b/arch/arm/dts/sun8i-h3-orangepi-2.dts index 597c425d08..9daffd90c1 100644 --- a/arch/arm/dts/sun8i-h3-orangepi-2.dts +++ b/arch/arm/dts/sun8i-h3-orangepi-2.dts @@ -99,8 +99,9 @@

sw4 { label = "sw4"; - linux,code = <BTN_0>; + linux,code = <KEY_POWER>; gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; + wakeup-source; }; };

diff --git a/arch/arm/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/dts/sun8i-h3-orangepi-pc.dts index 5aff8ecc66..90f75fa85e 100644 --- a/arch/arm/dts/sun8i-h3-orangepi-pc.dts +++ b/arch/arm/dts/sun8i-h3-orangepi-pc.dts @@ -91,8 +91,9 @@

sw4 { label = "sw4"; - linux,code = <BTN_0>; + linux,code = <KEY_POWER>; gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; + wakeup-source; }; }; }; diff --git a/arch/arm/dts/sun8i-h3.dtsi b/arch/arm/dts/sun8i-h3.dtsi index 4e89701df9..eac2349a23 100644 --- a/arch/arm/dts/sun8i-h3.dtsi +++ b/arch/arm/dts/sun8i-h3.dtsi @@ -44,7 +44,7 @@ #include <dt-bindings/thermal/thermal.h>

/ { - cpu0_opp_table: opp_table0 { + cpu0_opp_table: opp-table-cpu { compatible = "operating-points-v2"; opp-shared;

@@ -112,7 +112,7 @@ }; };

- gpu_opp_table: gpu-opp-table { + gpu_opp_table: opp-table-gpu { compatible = "operating-points-v2";

opp-120000000 { @@ -245,7 +245,7 @@ cpu_thermal: cpu-thermal { polling-delay-passive = <0>; polling-delay = <0>; - thermal-sensors = <&ths 0>; + thermal-sensors = <&ths>;

trips { cpu_hot_trip: cpu-hot { @@ -282,6 +282,10 @@ compatible = "allwinner,sun8i-h3-de2-clk"; };

+&mbus { + compatible = "allwinner,sun8i-h3-mbus"; +}; + &mmc0 { compatible = "allwinner,sun7i-a20-mmc"; clocks = <&ccu CLK_BUS_MMC0>, diff --git a/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi b/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi index 22466afd38..235994a4a2 100644 --- a/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi +++ b/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi @@ -16,15 +16,27 @@ regulator-type = "voltage"; regulator-boot-on; regulator-always-on; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1300000>; + regulator-min-microvolt = <1108475>; + regulator-max-microvolt = <1308475>; regulator-ramp-delay = <50>; /* 4ms */ gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */ gpios-states = <0x1>; - states = <1100000 0>, <1300000 1>; + states = <1108475 0>, <1308475 1>; }; };

&cpu0 { cpu-supply = <&reg_vdd_cpux>; }; + +&cpu1 { + cpu-supply = <&reg_vdd_cpux>; +}; + +&cpu2 { + cpu-supply = <&reg_vdd_cpux>; +}; + +&cpu3 { + cpu-supply = <&reg_vdd_cpux>; +}; diff --git a/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi b/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi index 8e5cb3b3fd..d03f5853ef 100644 --- a/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi +++ b/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi @@ -82,8 +82,9 @@

sw4 { label = "power"; - linux,code = <BTN_0>; + linux,code = <KEY_POWER>; gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; + wakeup-source; }; };

@@ -219,6 +220,7 @@

bluetooth { compatible = "brcm,bcm43438-bt"; + max-speed = <1500000>; clocks = <&rtc 1>; clock-names = "lpo"; vbat-supply = <&reg_vcc3v3>; diff --git a/arch/arm/dts/sunxi-h3-h5.dtsi b/arch/arm/dts/sunxi-h3-h5.dtsi index 9be13378d4..6cea57e07f 100644 --- a/arch/arm/dts/sunxi-h3-h5.dtsi +++ b/arch/arm/dts/sunxi-h3-h5.dtsi @@ -567,9 +567,14 @@ };

mbus: dram-controller@1c62000 { - compatible = "allwinner,sun8i-h3-mbus"; - reg = <0x01c62000 0x1000>; - clocks = <&ccu CLK_MBUS>; + /* compatible is in per SoC .dtsi file */ + reg = <0x01c62000 0x1000>, + <0x01c63000 0x1000>; + reg-names = "mbus", "dram"; + clocks = <&ccu CLK_MBUS>, + <&ccu CLK_DRAM>, + <&ccu CLK_BUS_DRAM>; + clock-names = "mbus", "dram", "bus"; #address-cells = <1>; #size-cells = <1>; dma-ranges = <0x00000000 0x40000000 0xc0000000>; @@ -812,8 +817,8 @@ reg-io-width = <1>; interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>, - <&ccu CLK_HDMI>; - clock-names = "iahb", "isfr", "tmds"; + <&ccu CLK_HDMI>, <&rtc 0>; + clock-names = "iahb", "isfr", "tmds", "cec"; resets = <&ccu RST_BUS_HDMI1>; reset-names = "ctrl"; phys = <&hdmi_phy>; @@ -859,6 +864,15 @@ #clock-cells = <1>; };

+ r_intc: interrupt-controller@1f00c00 { + compatible = "allwinner,sun8i-h3-r-intc", + "allwinner,sun6i-a31-r-intc"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x01f00c00 0x400>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + }; + r_ccu: clock@1f01400 { compatible = "allwinner,sun8i-h3-r-ccu"; reg = <0x01f01400 0x100>; @@ -897,6 +911,19 @@ #size-cells = <0>; };

+ r_uart: serial@1f02800 { + compatible = "snps,dw-apb-uart"; + reg = <0x01f02800 0x400>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&r_ccu CLK_APB0_UART>; + resets = <&r_ccu RST_APB0_UART>; + pinctrl-names = "default"; + pinctrl-0 = <&r_uart_pins>; + status = "disabled"; + }; + r_pio: pinctrl@1f02c00 { compatible = "allwinner,sun8i-h3-r-pinctrl"; reg = <0x01f02c00 0x400>; @@ -922,6 +949,11 @@ pins = "PL10"; function = "s_pwm"; }; + + r_uart_pins: r-uart-pins { + pins = "PL2", "PL3"; + function = "s_uart"; + }; };

r_pwm: pwm@1f03800 { diff --git a/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi b/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi index 19b3b23cfa..9e14fe5fdc 100644 --- a/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi +++ b/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi @@ -49,6 +49,7 @@ label = "power"; linux,code = <KEY_POWER>; gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ + wakeup-source; }; };

@@ -128,6 +129,18 @@ cpu-supply = <&reg_vdd_cpux>; };

+&cpu1 { + cpu-supply = <&reg_vdd_cpux>; +}; + +&cpu2 { + cpu-supply = <&reg_vdd_cpux>; +}; + +&cpu3 { + cpu-supply = <&reg_vdd_cpux>; +}; + &de { status = "okay"; }; diff --git a/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi b/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi index 204fba3614..50d328c2a8 100644 --- a/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi +++ b/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi @@ -156,7 +156,7 @@ &spi0 { status = "okay";

- spiflash@0 { + flash@0 { compatible = "jedec,spi-nor"; reg = <0>; spi-max-frequency = <50000000>;