Previously the SPL size on all iMX6 platforms was restricted to 68KB because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the other iMX6 variants have 256KB of OCRAM. Add an option CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which don't need to support the SL/DL variants. This allows for an SPL size of 196KB, which makes it much easier to use configurations such as SPL with driver model and FDT control.
Signed-off-by: Robert Hancock hancock@sedsystems.ca ---
Changed since v2: Remove "default n" in Kconfig since that is the default.
arch/arm/mach-imx/mx6/Kconfig | 9 +++++++++ common/spl/Kconfig | 3 ++- include/configs/imx6_spl.h | 28 ++++++++++++++++++++++++++-- 3 files changed, 37 insertions(+), 3 deletions(-)
diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig index fe5991e..9c27176 100644 --- a/arch/arm/mach-imx/mx6/Kconfig +++ b/arch/arm/mach-imx/mx6/Kconfig @@ -87,6 +87,15 @@ config MX6ULL select SYSCOUNTER_TIMER select SYS_L2CACHE_OFF
+config MX6_OCRAM_256KB + bool "Support 256KB OCRAM" + depends on MX6D || MX6Q + help + Allows using the full 256KB size of the OCRAM on the MX6Q/MX6D series + of chips, such as for SPL. The OCRAM of the Lite series of chips is + only 128KB, so using this option will prevent the resulting code from + working on those chips. + config MX6_DDRCAL bool "Include dynamic DDR calibration routines" depends on SPL diff --git a/common/spl/Kconfig b/common/spl/Kconfig index 54154b9..c5ad047 100644 --- a/common/spl/Kconfig +++ b/common/spl/Kconfig @@ -28,7 +28,8 @@ config SPL_FRAMEWORK config SPL_SIZE_LIMIT int "Maximum size of SPL image" depends on SPL - default 69632 if ARCH_MX6 + default 69632 if ARCH_MX6 && !MX6_OCRAM_256KB + default 200704 if ARCH_MX6 && MX6_OCRAM_256KB default 0 help Specifies the maximum length of the U-Boot SPL image. diff --git a/include/configs/imx6_spl.h b/include/configs/imx6_spl.h index 212dee7..a223930 100644 --- a/include/configs/imx6_spl.h +++ b/include/configs/imx6_spl.h @@ -7,10 +7,32 @@ #define __IMX6_SPL_CONFIG_H
#ifdef CONFIG_SPL + +#ifdef CONFIG_MX6_OCRAM_256KB /* - * see Figure 8-3 in IMX6DQ/IMX6SDL Reference manuals: + * see Figure 8.4.1 in IMX6DQ Reference manuals: + * - IMX6DQ OCRAM (IRAM) is from 0x00907000 to 0x0093FFFF + * - BOOT ROM stack is at 0x0093FFB8 + * - if icache/dcache is enabled (eFuse/strapping controlled) then the + * IMX BOOT ROM will setup MMU table at 0x00938000, therefore we need to + * fit between 0x00907000 and 0x00938000. + * - Additionally the BOOT ROM loads what they consider the firmware image + * which consists of a 4K header in front of us that contains the IVT, DCD + * and some padding thus 'our' max size is really 0x00908000 - 0x00938000 + * or 192KB + */ +#define CONFIG_SPL_MAX_SIZE 0x30000 +#define CONFIG_SPL_STACK 0x0093FFB8 +/* + * Pad SPL to 196KB (4KB header + 192KB max size). This allows to write the + * SPL/U-Boot combination generated with u-boot-with-spl.imx directly to a + * boot media (given that boot media specific offset is configured properly). + */ +#define CONFIG_SPL_PAD_TO 0x31000 +#else +/* + * see Figure 8-3 in IMX6SDL Reference manuals: * - IMX6SDL OCRAM (IRAM) is from 0x00907000 to 0x0091FFFF - * - IMX6DQ has 2x IRAM of IMX6SDL but we intend to support IMX6SDL as well * - BOOT ROM stack is at 0x0091FFB8 * - if icache/dcache is enabled (eFuse/strapping controlled) then the * IMX BOOT ROM will setup MMU table at 0x00918000, therefore we need to @@ -29,6 +51,8 @@ */ #define CONFIG_SPL_PAD_TO 0x11000
+#endif + /* MMC support */ #if defined(CONFIG_SPL_MMC_SUPPORT) #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1