From: Jon Loeliger jdl@freescale.com
Signed-off-by: Jon Loeliger jdl@freescale.com Signed-off-by: Kumar Gala galak@kernel.crashing.org --- board/freescale/mpc8610hpcd/Makefile | 10 +- board/freescale/mpc8610hpcd/ddr.c | 223 +++++++++++++++++++++++++++++ board/freescale/mpc8610hpcd/mpc8610hpcd.c | 3 +- include/configs/MPC8610HPCD.h | 50 +++++-- 4 files changed, 264 insertions(+), 22 deletions(-) create mode 100644 board/freescale/mpc8610hpcd/ddr.c
diff --git a/board/freescale/mpc8610hpcd/Makefile b/board/freescale/mpc8610hpcd/Makefile index a457c32..dc97c33 100644 --- a/board/freescale/mpc8610hpcd/Makefile +++ b/board/freescale/mpc8610hpcd/Makefile @@ -23,14 +23,14 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(BOARD).a
-COBJS := $(BOARD).o law.o +COBJS-y += $(BOARD).o +COBJS-y += ddr.o +COBJS-y += law.o
COBJS-${CONFIG_FSL_DIU_FB} += mpc8610hpcd_diu.o
-COBJS += ${COBJS-y} - -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS)) +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) SOBJS := $(addprefix $(obj),$(SOBJS))
$(LIB): $(obj).depend $(OBJS) $(SOBJS) diff --git a/board/freescale/mpc8610hpcd/ddr.c b/board/freescale/mpc8610hpcd/ddr.c new file mode 100644 index 0000000..fca2918 --- /dev/null +++ b/board/freescale/mpc8610hpcd/ddr.c @@ -0,0 +1,223 @@ +/* + * Copyright 2008 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include <common.h> +#include <i2c.h> + +#include <../cpu/mpc8xxx/fsl_ddr_sdram.h> + +#define SDRAM_TYPE_DDR1 2 +#define SDRAM_TYPE_DDR2 3 +#define SDRAM_TYPE_LPDDR1 6 +#define SDRAM_TYPE_DDR3 7 + +static void +get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address) +{ + i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t)); +} + +unsigned int fsl_ddr_get_mem_data_rate(void) +{ + return get_bus_freq(0); +} + + +void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd, + unsigned int ctrl_num) +{ + unsigned int i; + unsigned int i2c_address = 0; + + for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) { + if (ctrl_num == 0 && i == 0) { + i2c_address = SPD_EEPROM_ADDRESS1; + } + get_spd(&(ctrl_dimms_spd[i]), i2c_address); + } +} + +#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4) +#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL +#endif + +void fsl_ddr_dump_memctl_regs(unsigned int ctrl_num) +{ + unsigned int i; + volatile ccsr_ddr_t *ddr; + + if (ctrl_num == 0) + ddr = (void *)CFG_MPC86xx_DDR_ADDR; + else + ddr = (void *)CFG_MPC86xx_DDR2_ADDR; + + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + unsigned int bnds = 0; + unsigned int config = 0; + + if (i == 0) { + bnds = ddr->cs0_bnds; + config = ddr->cs0_config; + + } else if (i == 1) { + bnds = ddr->cs1_bnds; + config = ddr->cs1_config; + + } else if (i == 2) { + bnds = ddr->cs2_bnds; + config = ddr->cs2_config; + + } else { + bnds = ddr->cs3_bnds; + config = ddr->cs3_config; + + } + + printf("cs%u_bnds = %08X\n", i, bnds); + printf("cs%u_config = %08X\n", i, config); + } + + printf("timing_cfg_3 = %08X\n", ddr->timing_cfg_3); + printf("timing_cfg_0 = %08X\n", ddr->timing_cfg_0); + printf("timing_cfg_1 = %08X\n", ddr->timing_cfg_1); + printf("timing_cfg_2 = %08X\n", ddr->timing_cfg_2); + printf("ddr_sdram_cfg = %08X\n", ddr->sdram_cfg_1); + printf("ddr_sdram_cfg_2 = %08X\n", ddr->sdram_cfg_2); + printf("ddr_sdram_mode = %08X\n", ddr->sdram_mode_1); + printf("ddr_sdram_mode_2 = %08X\n", ddr->sdram_mode_2); + printf("ddr_sdram_interval = %08X\n", ddr->sdram_interval); + printf("ddr_data_init = %08X\n", ddr->sdram_data_init); + printf("ddr_sdram_clk_cntl = %08X\n", ddr->sdram_clk_cntl); + printf("ddr_init_addr = %08X\n", ddr->init_addr); +} + +void fsl_ddr_set_memctl_regs(const fsl_memctl_config_regs_t *regs, + unsigned int ctrl_num) +{ + unsigned int i; + volatile ccsr_ddr_t *ddr; + + switch (ctrl_num) { + case 0: + ddr = (void *)CFG_MPC86xx_DDR_ADDR; + break; + case 1: + ddr = (void *)CFG_MPC86xx_DDR2_ADDR; + break; + default: + printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num); + return; + } + + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + if (i == 0) { + ddr->cs0_bnds = regs->cs[i].bnds; + ddr->cs0_config = regs->cs[i].config; + + } else if (i == 1) { + ddr->cs1_bnds = regs->cs[i].bnds; + ddr->cs1_config = regs->cs[i].config; + + } else if (i == 2) { + ddr->cs2_bnds = regs->cs[i].bnds; + ddr->cs2_config = regs->cs[i].config; + + } else if (i == 3) { + ddr->cs3_bnds = regs->cs[i].bnds; + ddr->cs3_config = regs->cs[i].config; + } + } + + /* Someone decided to use different names from the documentation... */ + ddr->timing_cfg_3 = regs->timing_cfg_3; + ddr->timing_cfg_0 = regs->timing_cfg_0; + ddr->timing_cfg_1 = regs->timing_cfg_1; + ddr->timing_cfg_2 = regs->timing_cfg_2; + ddr->sdram_cfg_2 = regs->ddr_sdram_cfg_2; + ddr->sdram_mode_1 = regs->ddr_sdram_mode; + ddr->sdram_mode_2 = regs->ddr_sdram_mode_2; + ddr->sdram_interval = regs->ddr_sdram_interval; + ddr->sdram_data_init = regs->ddr_data_init; + ddr->sdram_clk_cntl = regs->ddr_sdram_clk_cntl; + ddr->init_addr = regs->ddr_init_addr; + ddr->init_ext_addr = regs->ddr_init_ext_addr; + + /* FIXME: ECC? Need to program err_disable, err_sbe, and err_int_en */ + printf("before go\n"); + + /* + * 200 painful micro-seconds must elapse between + * the DDR clock setup and the DDR config enable. + */ + udelay(200); + asm volatile("sync;isync"); + + ddr->sdram_cfg_1 = regs->ddr_sdram_cfg; + + /* Poll DDR_SDRAM_CFG_2[D_INIT] bit until auto-data init is done */ + while (ddr->sdram_cfg_2 & 0x10) { + udelay(10000); /* throttle polling rate */ + } +} + +unsigned int fsl_ddr_type_function(void) +{ + return SDRAM_TYPE_DDR2; +} + +/* + * factors to consider for clock adjust: + * - number of chips on bus + * - position of slot + * - DDR1 vs. DDR2? + * - ??? + * + * FIXME: need to figure out the function parameters necessary to compute + * FIXME: a clock adjust value + */ +unsigned int fsl_ddr_clk_adjust_function(void) +{ + return 7; +} + +/* + * factors to consider for CPO: + * - frequency + * - ddr1 vs. ddr2 + * + * FIXME: figure out how to compute or tabulate good values for this + */ +unsigned int fsl_ddr_cpo_override_function(void) +{ + return 10; +} + +/* + * factors to consider for write data delay: + * - number of DIMMs + * + * 1 = 1/4 clock delay + * 2 = 1/2 clock delay + * 3 = 3/4 clock delay + * 4 = 1 clock delay + * 5 = 5/4 clock delay + * 6 = 3/2 clock delay + */ +unsigned int fsl_ddr_write_data_delay_function(void) +{ + return 3; +} + +/* + * factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ +unsigned int fsl_ddr_half_strength_driver_enable_function(void) +{ + return 0; +} diff --git a/board/freescale/mpc8610hpcd/mpc8610hpcd.c b/board/freescale/mpc8610hpcd/mpc8610hpcd.c index ff1b892..34f845e 100644 --- a/board/freescale/mpc8610hpcd/mpc8610hpcd.c +++ b/board/freescale/mpc8610hpcd/mpc8610hpcd.c @@ -33,6 +33,7 @@ #include <spd_sdram.h>
#include "../common/pixis.h" +#include "../cpu/mpc8xxx/fsl_ddr_sdram.h"
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) extern void ddr_enable_ecc(unsigned int dram_size); @@ -122,7 +123,7 @@ initdram(int board_type) long dram_size = 0;
#if defined(CONFIG_SPD_EEPROM) - dram_size = spd_sdram(); + dram_size = fsl_ddr_sdram(); #else dram_size = fixed_sdram(); #endif diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index e9371a2..e8d80b1 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -8,7 +8,6 @@
/* * MPC8610HPCD board configuration file - * */
#ifndef __CONFIG_H @@ -45,14 +44,6 @@ #define CONFIG_FSL_LAW 1 /* Use common FSL init code */
#define CONFIG_ENV_OVERWRITE - -#define CONFIG_SPD_EEPROM /* Use SPD for DDR */ -#undef CONFIG_DDR_DLL /* possible DLL fix needed */ -#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ -#undef CONFIG_DDR_ECC /* only for ECC DDR module */ -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef -#define CONFIG_NUM_DDR_CONTROLLERS 1 #define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
#define CONFIG_HIGH_BATS 1 /* High BATs supported & enabled */ @@ -92,22 +83,46 @@ /* * DDR Setup */ +#define CONFIG_FSL_DDR2 +#undef CONFIG_FSL_DDR_INTERACTIVE +#define CONFIG_SPD_EEPROM /* Use SPD for DDR */ +#define CONFIG_DDR_SPD + +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + #define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ #define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE #define CONFIG_VERY_BIG_RAM
#define MPC86xx_DDR_SDRAM_CLK_CNTL
-#if defined(CONFIG_SPD_EEPROM) + /* - * Determine DDR configuration from I2C interface. + * Number of memory controllers on device */ -#define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */ -#else +#define CONFIG_NUM_DDR_CONTROLLERS 1 + +/* + * Number of DIMM slots per memory controller + */ +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 + /* - * Manually set up DDR1 parameters + * Number of chip selects per memory controller */ +#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) + + +/* + * I2C addresses of SPD EEPROMs + */ +#define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ +
+/* + * These are used when DDR doesn't use SPD. + */ #define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
#if 0 /* TODO */ @@ -130,7 +145,10 @@ #define CFG_DDR_ERR_INT_EN 0x00000000 #define CFG_DDR_ERR_DIS 0x00000000 #define CFG_DDR_SBE 0x000f0000 - /* Not used in fixed_sdram function */ + +/* + * FIXME: Not used in fixed_sdram function + */ #define CFG_DDR_MODE 0x00000022 #define CFG_DDR_CS1_BNDS 0x00000000 #define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */ @@ -138,7 +156,7 @@ #define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */ #define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */ #endif -#endif +
#define CONFIG_ID_EEPROM #define CFG_I2C_EEPROM_NXID