Add zlib (v1.2.11) uncompr() function to U-Boot. SquashFS depends on this function to decompress data from a raw disk image. The actual support for zlib into SquashFS sources will be added in a follow-up commit.
Signed-off-by: Joao Marcos Costa joaomarcos.costa@bootlin.com --- Changes in v2: - Changed commit title and message, which were wrong and/or misleading in v1. include/u-boot/zlib.h | 32 ++++++++++++++ lib/zlib/uncompr.c | 97 +++++++++++++++++++++++++++++++++++++++++++ lib/zlib/zlib.c | 1 + 3 files changed, 130 insertions(+) create mode 100644 lib/zlib/uncompr.c
diff --git a/include/u-boot/zlib.h b/include/u-boot/zlib.h index e23ceb50ca..a33cc8780d 100644 --- a/include/u-boot/zlib.h +++ b/include/u-boot/zlib.h @@ -110,6 +110,12 @@ extern "C" { # define voidp z_voidp #endif
+#if defined(ZLIB_CONST) && !defined(z_const) +# define z_const const +#else +# define z_const +#endif + #if defined(__MSDOS__) && !defined(MSDOS) # define MSDOS #endif @@ -710,6 +716,32 @@ ZEXTERN uInt ZEXPORT crc32 OF((uInt crc, const Bytef *buf, uInt len)); if (crc != original_crc) error(); */
+ZEXTERN int ZEXPORT uncompress OF((Bytef *dest, uLongf *destLen, + const Bytef *source, uLong sourceLen)); +/* + Decompresses the source buffer into the destination buffer. sourceLen is + the byte length of the source buffer. Upon entry, destLen is the total size + of the destination buffer, which must be large enough to hold the entire + uncompressed data. (The size of the uncompressed data must have been saved + previously by the compressor and transmitted to the decompressor by some + mechanism outside the scope of this compression library.) Upon exit, destLen + is the actual size of the uncompressed data. + + uncompress returns Z_OK if success, Z_MEM_ERROR if there was not + enough memory, Z_BUF_ERROR if there was not enough room in the output + buffer, or Z_DATA_ERROR if the input data was corrupted or incomplete. In + the case where there is not enough room, uncompress() will fill the output + buffer with the uncompressed data up to that point. +*/ + +ZEXTERN int ZEXPORT uncompress2 OF((Bytef *dest, uLongf *destLen, + const Bytef *source, uLong *sourceLen)); +/* + Same as uncompress, except that sourceLen is a pointer, where the + length of the source is *sourceLen. On return, *sourceLen is the number of + source bytes consumed. +*/ + ZEXTERN int ZEXPORT inflateInit2_ OF((z_streamp strm, int windowBits, const char *version, int stream_size)); #define inflateInit(strm) \ diff --git a/lib/zlib/uncompr.c b/lib/zlib/uncompr.c new file mode 100644 index 0000000000..21e93933b2 --- /dev/null +++ b/lib/zlib/uncompr.c @@ -0,0 +1,97 @@ +/* uncompr.c -- decompress a memory buffer + * Copyright (C) 1995-2003, 2010, 2014, 2016 Jean-loup Gailly, Mark Adler + * For conditions of distribution and use, see copyright notice in zlib.h + */ + +/* @(#) $Id$ */ + +#define ZLIB_INTERNAL +#include "zlib.h" + +/* =========================================================================== + Decompresses the source buffer into the destination buffer. *sourceLen is + the byte length of the source buffer. Upon entry, *destLen is the total size + of the destination buffer, which must be large enough to hold the entire + uncompressed data. (The size of the uncompressed data must have been saved + previously by the compressor and transmitted to the decompressor by some + mechanism outside the scope of this compression library.) Upon exit, + *destLen is the size of the decompressed data and *sourceLen is the number + of source bytes consumed. Upon return, source + *sourceLen points to the + first unused input byte. + + uncompress returns Z_OK if success, Z_MEM_ERROR if there was not enough + memory, Z_BUF_ERROR if there was not enough room in the output buffer, or + Z_DATA_ERROR if the input data was corrupted, including if the input data is + an incomplete zlib stream. +*/ +int ZEXPORT uncompress2(dest, destLen, source, sourceLen) + Bytef *dest; + uLongf *destLen; + const Bytef *source; + uLong *sourceLen; + +{ + z_stream stream; + int err; + const uInt max = (uInt)-1; + uLong len, left; + /* for detection of incomplete stream when *destLen == 0 */ + Byte buf[1]; + + len = *sourceLen; + if (*destLen) { + left = *destLen; + *destLen = 0; + } else { + left = 1; + dest = buf; + } + + stream.next_in = (z_const Bytef *)source; + stream.avail_in = 0; + stream.zalloc = (alloc_func)0; + stream.zfree = (free_func)0; + stream.opaque = (voidpf)0; + + err = inflateInit(&stream); + if (err != Z_OK) + return err; + + stream.next_out = dest; + stream.avail_out = 0; + + do { + if (stream.avail_out == 0) { + stream.avail_out = left > (uLong)max ? max : (uInt)left; + left -= stream.avail_out; + } + + if (stream.avail_in == 0) { + stream.avail_in = len > (uLong)max ? max : (uInt)len; + len -= stream.avail_in; + } + + err = inflate(&stream, Z_NO_FLUSH); + } while (err == Z_OK); + + *sourceLen -= len + stream.avail_in; + if (dest != buf) + *destLen = stream.total_out; + else if (stream.total_out && err == Z_BUF_ERROR) + left = 1; + + inflateEnd(&stream); + return err == Z_STREAM_END ? Z_OK : + err == Z_NEED_DICT ? Z_DATA_ERROR : + err == Z_BUF_ERROR && left + stream.avail_out ? Z_DATA_ERROR : + err; +} + +int ZEXPORT uncompress(dest, destLen, source, sourceLen) + Bytef *dest; + uLongf *destLen; + const Bytef *source; + uLong sourceLen; +{ + return uncompress2(dest, destLen, source, &sourceLen); +} diff --git a/lib/zlib/zlib.c b/lib/zlib/zlib.c index 7e1570292c..05a2734086 100644 --- a/lib/zlib/zlib.c +++ b/lib/zlib/zlib.c @@ -30,3 +30,4 @@ #include "inflate.c" #include "zutil.c" #include "adler32.c" +#include "uncompr.c"