Dear Kim Phillips,
In message 20090819200321.a0900c41.kim.phillips@freescale.com you wrote:
commit 9993e196da707a0a1cd4584f1fcef12382c1c144 "mpc83xx: convert all remaining boards over to 83XX_GENERIC_PCI" remapped pci windows on tqm834x to make it more consistent with the other 83xx boards. During that time however, the author failed to realize that FLASH_BASE was occupying the same range as what PCI1_MEM_BASE was being assigned.
Signed-off-by: Kim Phillips kim.phillips@freescale.com
WD, if you have time, please test - I don't have a tqm834x board. TIA.
include/configs/TQM834x.h | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)
Tested-by: Wolfgang Denk wd@denx.de
I can verify that the original problem (non working flash support) gets fixed by this patch:
without the patch:
U-Boot 2009.06-00513-g982adfc (Jul 24 2009 - 15:42:41) MPC83XX
Reset Status: External/Internal Soft, External/Internal Hard
CPU: e300c1, MPC8349E, Rev: 1.1 at 533.328 MHz, CSB: 266.664 MHz Board: TQM834x PCI1: 32 bit, 33 MHz I2C: ready DRAM: 256 MB FLASH: ## Unknown FLASH on Bank 1 - Size = 0x02000000 = 0 MB 32 MB PCI: Bus Dev VenId DevId Class Int 00 0b 104c ac55 0607 ff 00 0b 104c ac55 0607 ff DTT: 1 is 27 C Net: TSEC0, TSEC1 ...
with the patch:
U-Boot 2009.08-rc2-00026-g5c023da (Aug 20 2009 - 10:41:53) MPC83XX
Reset Status: External/Internal Soft, External/Internal Hard
CPU: e300c1, MPC8349E, Rev: 1.1 at 533.328 MHz, CSB: 266.664 MHz Board: TQM834x PCI1: 32 bit, 33 MHz I2C: ready DRAM: 256 MB FLASH: 32 MB PCI: Bus Dev VenId DevId Class Int 00 0b 104c ac55 0607 ff 00 0b 104c ac55 0607 ff DTT: 1 is 34 C Net: TSEC0, TSEC1 ...
But I have a question (unrelated to this patch):
With recent versions of U-Boot I see unstable network behaviour:
=> run load TSEC0: No link. TSEC1: No link. => run load Speed: 1000, full duplex Using TSEC0 device TFTP from server 192.168.1.1; our IP address is 192.168.205.1 Filename 'tqm834x/u-boot.bin'. Load address: 0x200000 Loading: ##############Got error 4 #### done Bytes transferred = 253376 (3ddc0 hex)
=> run load Speed: 1000, full duplex Using TSEC0 device TFTP from server 192.168.1.1; our IP address is 192.168.205.1 Filename 'tqm834x/u-boot.bin'. Load address: 0x200000 Loading: #Got error 4 #Got error 4 Got error 4 T T ################ done Bytes transferred = 253376 (3ddc0 hex)
=> run load Speed: 1000, full duplex Using TSEC0 device TFTP from server 192.168.1.1; our IP address is 192.168.205.1 Filename 'tqm834x/u-boot.bin'. Load address: 0x200000 Loading: #######Got error 4 #Got error 4 ####Got error 4 Got error 4 #Got error 4 ##### done Bytes transferred = 253376 (3ddc0 hex)
Do you have any idea what might go wrong here?
[Sorry, I didn't find time yet to try bisecting this, but maybe this rings a bell to you?]
Best regards,
Wolfgang Denk