[U-Boot] [PATCH 1/2] sunxi: power: add AXP803 support

23 Dec 2016

The A64 uses the AXP803 as its PMIC.
Signed-off-by: Icenowy Zheng icenowy@aosc.xyz
---
 arch/arm/mach-sunxi/Makefile   |   3 +
 arch/arm/mach-sunxi/pmic_bus.c |   6 +-
 arch/arm/mach-sunxi/rsb.c      |   2 +-
 board/sunxi/board.c            |  31 ++---
 drivers/power/Kconfig          |  87 ++++++++------
 drivers/power/Makefile         |   1 +
 drivers/power/axp803.c         | 255 +++++++++++++++++++++++++++++++++++++++++
 drivers/power/axp818.c         |   2 +-
 include/axp803.h               |  73 ++++++++++++
 include/axp_pmic.h             |   3 +
 10 files changed, 413 insertions(+), 50 deletions(-)
 create mode 100644 drivers/power/axp803.c
 create mode 100644 include/axp803.h

diff --git a/arch/arm/mach-sunxi/Makefile b/arch/arm/mach-sunxi/Makefile
index 128091e4e6..dcf2b5245d 100644
--- a/arch/arm/mach-sunxi/Makefile
+++ b/arch/arm/mach-sunxi/Makefile
@@ -19,9 +19,11 @@ endif
 obj-$(CONFIG_MACH_SUN6I)	+= prcm.o
 obj-$(CONFIG_MACH_SUN8I)	+= prcm.o
 obj-$(CONFIG_MACH_SUN9I)	+= prcm.o
+obj-$(CONFIG_MACH_SUN50I)	+= prcm.o
 obj-$(CONFIG_MACH_SUN6I)	+= p2wi.o
 obj-$(CONFIG_MACH_SUN8I)	+= rsb.o
 obj-$(CONFIG_MACH_SUN9I)	+= rsb.o
+obj-$(CONFIG_MACH_SUN50I)	+= rsb.o
 obj-$(CONFIG_MACH_SUN4I)	+= clock_sun4i.o
 obj-$(CONFIG_MACH_SUN5I)	+= clock_sun4i.o
 obj-$(CONFIG_MACH_SUN6I)	+= clock_sun6i.o
@@ -37,6 +39,7 @@ obj-$(CONFIG_MACH_SUN9I)	+= clock_sun9i.o gtbus_sun9i.o
 obj-$(CONFIG_AXP152_POWER)	+= pmic_bus.o
 obj-$(CONFIG_AXP209_POWER)	+= pmic_bus.o
 obj-$(CONFIG_AXP221_POWER)	+= pmic_bus.o
+obj-$(CONFIG_AXP803_POWER)	+= pmic_bus.o
 obj-$(CONFIG_AXP809_POWER)	+= pmic_bus.o
 obj-$(CONFIG_AXP818_POWER)	+= pmic_bus.o
diff --git a/arch/arm/mach-sunxi/pmic_bus.c b/arch/arm/mach-sunxi/pmic_bus.c
index 7c57f02792..0ac64a97cf 100644
--- a/arch/arm/mach-sunxi/pmic_bus.c
+++ b/arch/arm/mach-sunxi/pmic_bus.c
@@ -36,7 +36,7 @@ int pmic_bus_init(void)
    if (!needs_init)
    	return 0;
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
+#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
 # ifdef CONFIG_MACH_SUN6I
    p2wi_init();
    ret = p2wi_change_to_p2wi_mode(AXP221_CHIP_ADDR, AXP221_CTRL_ADDR,
@@ -62,7 +62,7 @@ int pmic_bus_read(u8 reg, u8 *data)
    return i2c_read(AXP152_I2C_ADDR, reg, 1, data, 1);
 #elif defined CONFIG_AXP209_POWER
    return i2c_read(AXP209_I2C_ADDR, reg, 1, data, 1);
-#elif defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
+#elif defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
 # ifdef CONFIG_MACH_SUN6I
    return p2wi_read(reg, data);
 # else
@@ -77,7 +77,7 @@ int pmic_bus_write(u8 reg, u8 data)
    return i2c_write(AXP152_I2C_ADDR, reg, 1, &data, 1);
 #elif defined CONFIG_AXP209_POWER
    return i2c_write(AXP209_I2C_ADDR, reg, 1, &data, 1);
-#elif defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
+#elif defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
 # ifdef CONFIG_MACH_SUN6I
    return p2wi_write(reg, data);
 # else
diff --git a/arch/arm/mach-sunxi/rsb.c b/arch/arm/mach-sunxi/rsb.c
index 6fd11f1529..28d05e962a 100644
--- a/arch/arm/mach-sunxi/rsb.c
+++ b/arch/arm/mach-sunxi/rsb.c
@@ -20,7 +20,7 @@ static int rsb_set_device_mode(void);
static void rsb_cfg_io(void)
 {
-#ifdef CONFIG_MACH_SUN8I
+#if defined CONFIG_MACH_SUN8I || defined CONFIG_MACH_SUN50I
    sunxi_gpio_set_cfgpin(SUNXI_GPL(0), SUN8I_GPL_R_RSB);
    sunxi_gpio_set_cfgpin(SUNXI_GPL(1), SUN8I_GPL_R_RSB);
    sunxi_gpio_set_pull(SUNXI_GPL(0), 1);
diff --git a/board/sunxi/board.c b/board/sunxi/board.c
index 53656383d5..3435b80c14 100644
--- a/board/sunxi/board.c
+++ b/board/sunxi/board.c
@@ -487,26 +487,27 @@ void sunxi_board_init(void)
 #endif
#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \
-	defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
+	defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || \
+	defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
    power_failed = axp_init();
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
+#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || \
+	defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
    power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT);
 #endif
    power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT);
    power_failed |= axp_set_dcdc3(CONFIG_AXP_DCDC3_VOLT);
-#if !defined(CONFIG_AXP209_POWER) && !defined(CONFIG_AXP818_POWER)
+#if !defined(CONFIG_AXP209_POWER) && !defined(CONFIG_AXP803_POWER) && \
+	!defined(CONFIG_AXP818_POWER)
    power_failed |= axp_set_dcdc4(CONFIG_AXP_DCDC4_VOLT);
 #endif
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
+#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || \
+	defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
    power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
 #endif
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
+#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || \
+	defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
    power_failed |= axp_set_aldo1(CONFIG_AXP_ALDO1_VOLT);
 #endif
    power_failed |= axp_set_aldo2(CONFIG_AXP_ALDO2_VOLT);
@@ -517,8 +518,8 @@ void sunxi_board_init(void)
    power_failed |= axp_set_aldo4(CONFIG_AXP_ALDO4_VOLT);
 #endif
-#if defined(CONFIG_AXP221_POWER) || defined(CONFIG_AXP809_POWER) || \
-	defined(CONFIG_AXP818_POWER)
+#if defined(CONFIG_AXP221_POWER) || defined(CONFIG_AXP803_POWER) || \
+	defined(CONFIG_AXP809_POWER) || defined(CONFIG_AXP818_POWER)
    power_failed |= axp_set_dldo(1, CONFIG_AXP_DLDO1_VOLT);
    power_failed |= axp_set_dldo(2, CONFIG_AXP_DLDO2_VOLT);
 #if !defined CONFIG_AXP809_POWER
@@ -530,13 +531,17 @@ void sunxi_board_init(void)
    power_failed |= axp_set_eldo(3, CONFIG_AXP_ELDO3_VOLT);
 #endif
-#ifdef CONFIG_AXP818_POWER
+#if defined CONFIG_AXP803_POWER || defined CONFIG_AXP818_POWER
    power_failed |= axp_set_fldo(1, CONFIG_AXP_FLDO1_VOLT);
    power_failed |= axp_set_fldo(2, CONFIG_AXP_FLDO2_VOLT);
+#endif
+
+#ifdef CONFIG_AXP818_POWER
    power_failed |= axp_set_fldo(3, CONFIG_AXP_FLDO3_VOLT);
 #endif
-#if defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
+#if defined CONFIG_AXP803_POWER || defined CONFIG_AXP809_POWER || \
+	defined CONFIG_AXP818_POWER
    power_failed |= axp_set_sw(IS_ENABLED(CONFIG_AXP_SW_ON));
 #endif
 #endif
diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index f2c5629be2..e6f5903a17 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -11,8 +11,9 @@ choice
    depends on ARCH_SUNXI
    default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
    default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
+	default AXP803_POWER if MACH_SUN50I
    default AXP818_POWER if MACH_SUN8I_A83T
-	default SUNXI_NO_PMIC if MACH_SUN8I_H3 || MACH_SUN50I
+	default SUNXI_NO_PMIC if MACH_SUN8I_H3
config SUNXI_NO_PMIC
    bool "board without a pmic"
@@ -43,6 +44,13 @@ config AXP221_POWER
    Select this to enable support for the axp221/axp223 pmic found on most
    A23 and A31 boards.
+config AXP803_POWER
+	bool "axp803 pmic support"
+	depends on MACH_SUN50I
+	select CMD_POWEROFF
+	---help---
+	Say y here to enable support for the axp803 pmic found on A64 boards.
+
 config AXP809_POWER
    bool "axp809 pmic support"
    depends on MACH_SUN9I
@@ -69,25 +77,25 @@ endchoice
config AXP_DCDC1_VOLT
    int "axp pmic dcdc1 voltage"
-	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
-	default 3300 if AXP818_POWER
+	depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
+	default 3300 if AXP818_POWER || MACH_SUN50I
    default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
    ---help---
    Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to
    disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for
    generic 3.3V IO voltage for external devices like the lcd-panal and
    sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to
-	save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T
-	dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally
-	powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG.
+	save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T and
+	A64 dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1
+	normally powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG.
config AXP_DCDC2_VOLT
    int "axp pmic dcdc2 voltage"
-	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
+	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
    default 900 if AXP818_POWER
    default 1400 if AXP152_POWER || AXP209_POWER
    default 1200 if MACH_SUN6I
-	default 1100 if MACH_SUN8I
+	default 1100 if MACH_SUN8I || MACH_SUN50I
    default 0 if MACH_SUN9I
    ---help---
    Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to
@@ -97,15 +105,17 @@ config AXP_DCDC2_VOLT
    On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V.
    On A80 boards dcdc2 powers the GPU and can be left off.
    On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
+	On A64 boards dcdc2 is used with dcdc3 for VDD-CPU and should be 1.1V.
config AXP_DCDC3_VOLT
    int "axp pmic dcdc3 voltage"
-	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
+	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
    default 900 if AXP809_POWER || AXP818_POWER
    default 1500 if AXP152_POWER
    default 1250 if AXP209_POWER
    default 1200 if MACH_SUN6I || MACH_SUN8I
-	---help---
+	default 1100 if MACH_SUN50I
+---help---
    Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to
    disable dcdc3.
    On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and
@@ -114,39 +124,42 @@ config AXP_DCDC3_VOLT
    On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V.
    On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V.
    On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
+	On A64 boards dcdc3 is used with dcdc2 for VDD-CPU and should be 1.1V.
config AXP_DCDC4_VOLT
    int "axp pmic dcdc4 voltage"
-	depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
+	depends on AXP152_POWER || AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
    default 1250 if AXP152_POWER
    default 1200 if MACH_SUN6I
    default 0 if MACH_SUN8I
    default 900 if MACH_SUN9I
+	default 0 if MACH_SUN50I
    ---help---
    Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to
    disable dcdc4.
    On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V.
    On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V.
-	On A23 / A33 boards dcdc4 is unused and should be disabled.
+	On A23 / A33 / A64 boards dcdc4 is unused and should be disabled.
    On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V.
    On A83T boards dcdc4 is used for VDD-GPU.
config AXP_DCDC5_VOLT
    int "axp pmic dcdc5 voltage"
-	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
-	default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
+	depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
+	default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I || MACH_SUN50I
    ---help---
    Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to
    disable dcdc5.
-	On A23 / A31 / A33 / A80 / A83T boards dcdc5 is VCC-DRAM and
+	On A23 / A31 / A33 / A64 / A80 / A83T boards dcdc5 is VCC-DRAM and
    should be 1.5V, 1.35V if DDR3L is used.
config AXP_ALDO1_VOLT
    int "axp pmic (a)ldo1 voltage"
-	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
+	depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
    default 0 if MACH_SUN6I
    default 1800 if MACH_SUN8I_A83T
    default 3000 if MACH_SUN8I || MACH_SUN9I
+	default 2800 if MACH_SUN50I
    ---help---
    Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to
    disable aldo1.
@@ -155,14 +168,16 @@ config AXP_ALDO1_VOLT
    On A80 boards aldo1 powers the USB hosts and should be 3.0V.
    On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and
    should be 1.8V.
+	On A64 boards aldo1 powers PE pingroup and CSI and should be 2.8V.
config AXP_ALDO2_VOLT
    int "axp pmic (a)ldo2 voltage"
-	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
+	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
    default 3000 if AXP152_POWER || AXP209_POWER
    default 0 if MACH_SUN6I || MACH_SUN9I
    default 1800 if MACH_SUN8I_A83T
    default 2500 if MACH_SUN8I
+	default 1800 if MACH_SUN50I
    ---help---
    Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to
    disable aldo2.
@@ -173,17 +188,19 @@ config AXP_ALDO2_VOLT
    On A80 boards aldo2 powers PB pingroup and camera IO and can be left off.
    On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC,
    LPDDR2, and the codec. It should be 1.8V.
+	On A64 boards aldo2 powers PL pingroup and should be 1.8V.
config AXP_ALDO3_VOLT
    int "axp pmic (a)ldo3 voltage"
-	depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
+	depends on AXP209_POWER || AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
    default 0 if AXP209_POWER || MACH_SUN9I
-	default 3000 if MACH_SUN6I || MACH_SUN8I
+	default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN50I
    ---help---
    Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to
    disable aldo3.
    On A10(s) / A13 / A20 boards aldo3 should be 2.8V.
-	On A23 / A31 / A33 boards aldo3 is VCC-PLL and AVCC and should be 3.0V.
+	On A23 / A31 / A33 / A64 boards aldo3 is VCC-PLL and AVCC
+	and should be 3.0V.
    On A80 boards aldo3 is normally not used.
    On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
    3.0V.
@@ -199,17 +216,19 @@ config AXP_ALDO4_VOLT
config AXP_DLDO1_VOLT
    int "axp pmic dldo1 voltage"
-	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
+	depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
+	default 3300 if MACH_SUN50I
    default 0
    ---help---
    Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to
    disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used
    to power the ethernet phy. On A23, A33 and A80 boards this is often
-	used to power the wifi.
+	used to power the wifi. On A64 boards this is often used to power the
+	HDMI.
config AXP_DLDO2_VOLT
    int "axp pmic dldo2 voltage"
-	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
+	depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
    default 3000 if MACH_SUN9I
    default 0
    ---help---
@@ -219,7 +238,7 @@ config AXP_DLDO2_VOLT
config AXP_DLDO3_VOLT
    int "axp pmic dldo3 voltage"
-	depends on AXP221_POWER || AXP818_POWER
+	depends on AXP221_POWER || AXP803_POWER || AXP818_POWER
    default 0
    ---help---
    Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to
@@ -227,7 +246,7 @@ config AXP_DLDO3_VOLT
config AXP_DLDO4_VOLT
    int "axp pmic dldo4 voltage"
-	depends on AXP221_POWER || AXP818_POWER
+	depends on AXP221_POWER || AXP803_POWER || AXP818_POWER
    default 0
    ---help---
    Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to
@@ -235,15 +254,17 @@ config AXP_DLDO4_VOLT
config AXP_ELDO1_VOLT
    int "axp pmic eldo1 voltage"
-	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
+	depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
+	default 1800 if MACH_SUN50I
    default 0
    ---help---
    Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to
    disable eldo1.
+	On A64 boards it's used for the codec and should be 1.8V.
config AXP_ELDO2_VOLT
    int "axp pmic eldo2 voltage"
-	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
+	depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
    default 0
    ---help---
    Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to
@@ -251,7 +272,7 @@ config AXP_ELDO2_VOLT
config AXP_ELDO3_VOLT
    int "axp pmic eldo3 voltage"
-	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
+	depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
    default 3000 if MACH_SUN9I
    default 0
    ---help---
@@ -263,8 +284,8 @@ config AXP_ELDO3_VOLT
config AXP_FLDO1_VOLT
    int "axp pmic fldo1 voltage"
-	depends on AXP818_POWER
-	default 0 if MACH_SUN8I_A83T
+	depends on AXP803_POWER || AXP818_POWER
+	default 0
    ---help---
    Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to
    disable fldo1.
@@ -273,11 +294,13 @@ config AXP_FLDO1_VOLT
config AXP_FLDO2_VOLT
    int "axp pmic fldo2 voltage"
-	depends on AXP818_POWER
+	depends on AXP803_POWER || AXP818_POWER
+	default 1100 if MACH_SUN50I
    default 900 if MACH_SUN8I_A83T
    ---help---
    Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to
    disable fldo2.
+	On A64 boards fldo2 is VCC-CPUS and should be 1.1V.
    On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V.
config AXP_FLDO3_VOLT
@@ -290,7 +313,7 @@ config AXP_FLDO3_VOLT
config AXP_SW_ON
    bool "axp pmic sw on"
-	depends on AXP809_POWER || AXP818_POWER
+	depends on AXP803_POWER || AXP809_POWER || AXP818_POWER
    default n
    ---help---
    Enable to turn on axp pmic sw.
diff --git a/drivers/power/Makefile b/drivers/power/Makefile
index b43523e628..1449e875ce 100644
--- a/drivers/power/Makefile
+++ b/drivers/power/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_AS3722_POWER)	+= as3722.o
 obj-$(CONFIG_AXP152_POWER)	+= axp152.o
 obj-$(CONFIG_AXP209_POWER)	+= axp209.o
 obj-$(CONFIG_AXP221_POWER)	+= axp221.o
+obj-$(CONFIG_AXP803_POWER)	+= axp803.o
 obj-$(CONFIG_AXP809_POWER)	+= axp809.o
 obj-$(CONFIG_AXP818_POWER)	+= axp818.o
 obj-$(CONFIG_EXYNOS_TMU)	+= exynos-tmu.o
diff --git a/drivers/power/axp803.c b/drivers/power/axp803.c
new file mode 100644
index 0000000000..ac65a5c7ec
--- /dev/null
+++ b/drivers/power/axp803.c
@@ -0,0 +1,255 @@
+/*
+ * AXP803 driver based on AXP818 driver
+ *
+ * Based on axp818.c
+ * (C) Copyright 2015 Vishnu Patekar vishnuptekar0510@gmail.com
+ *
+ * Based on axp221.c
+ * (C) Copyright 2014 Hans de Goede hdegoede@redhat.com
+ * (C) Copyright 2013 Oliver Schinagl oliver@schinagl.nl
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/pmic_bus.h>
+#include <axp_pmic.h>
+
+static u8 axp803_mvolt_to_cfg(int mvolt, int min, int max, int div)
+{
+	if (mvolt < min)
+		mvolt = min;
+	else if (mvolt > max)
+		mvolt = max;
+
+	return  (mvolt - min) / div;
+}
+
+int axp_set_dcdc1(unsigned int mvolt)
+{
+	int ret;
+	u8 cfg = axp803_mvolt_to_cfg(mvolt, 1600, 3400, 100);
+
+	if (mvolt == 0)
+		return pmic_bus_clrbits(AXP803_OUTPUT_CTRL1,
+					AXP803_OUTPUT_CTRL1_DCDC1_EN);
+
+	ret = pmic_bus_write(AXP803_DCDC1_CTRL, cfg);
+	if (ret)
+		return ret;
+
+	return pmic_bus_setbits(AXP803_OUTPUT_CTRL1,
+				AXP803_OUTPUT_CTRL1_DCDC1_EN);
+}
+
+int axp_set_dcdc2(unsigned int mvolt)
+{
+	int ret;
+	u8 cfg;
+
+	if (mvolt >= 1220)
+		cfg = 70 + axp803_mvolt_to_cfg(mvolt, 1220, 1300, 20);
+	else
+		cfg = axp803_mvolt_to_cfg(mvolt, 500, 1200, 10);
+
+	if (mvolt == 0)
+		return pmic_bus_clrbits(AXP803_OUTPUT_CTRL1,
+					AXP803_OUTPUT_CTRL1_DCDC2_EN);
+
+	ret = pmic_bus_write(AXP803_DCDC2_CTRL, cfg);
+	if (ret)
+		return ret;
+
+	return pmic_bus_setbits(AXP803_OUTPUT_CTRL1,
+				AXP803_OUTPUT_CTRL1_DCDC2_EN);
+}
+
+int axp_set_dcdc3(unsigned int mvolt)
+{
+	int ret;
+	u8 cfg;
+
+	if (mvolt >= 1220)
+		cfg = 70 + axp803_mvolt_to_cfg(mvolt, 1220, 1300, 20);
+	else
+		cfg = axp803_mvolt_to_cfg(mvolt, 500, 1200, 10);
+
+	if (mvolt == 0)
+		return pmic_bus_clrbits(AXP803_OUTPUT_CTRL1,
+					AXP803_OUTPUT_CTRL1_DCDC3_EN);
+
+	ret = pmic_bus_write(AXP803_DCDC3_CTRL, cfg);
+	if (ret)
+		return ret;
+
+	return pmic_bus_setbits(AXP803_OUTPUT_CTRL1,
+				AXP803_OUTPUT_CTRL1_DCDC3_EN);
+}
+
+int axp_set_dcdc5(unsigned int mvolt)
+{
+	int ret;
+	u8 cfg;
+
+	if (mvolt >= 1140)
+		cfg = 32 + axp803_mvolt_to_cfg(mvolt, 1140, 1840, 20);
+	else
+		cfg = axp803_mvolt_to_cfg(mvolt, 800, 1120, 10);
+
+	if (mvolt == 0)
+		return pmic_bus_clrbits(AXP803_OUTPUT_CTRL1,
+					AXP803_OUTPUT_CTRL1_DCDC5_EN);
+
+	ret = pmic_bus_write(AXP803_DCDC5_CTRL, cfg);
+	if (ret)
+		return ret;
+
+	return pmic_bus_setbits(AXP803_OUTPUT_CTRL1,
+				AXP803_OUTPUT_CTRL1_DCDC5_EN);
+}
+
+int axp_set_aldo(int aldo_num, unsigned int mvolt)
+{
+	int ret;
+	u8 cfg;
+
+	if (aldo_num < 1 || aldo_num > 3)
+		return -EINVAL;
+
+	if (mvolt == 0)
+		return pmic_bus_clrbits(AXP803_OUTPUT_CTRL3,
+				AXP803_OUTPUT_CTRL3_ALDO1_EN << (aldo_num - 1));
+
+	cfg = axp803_mvolt_to_cfg(mvolt, 700, 3300, 100);
+	ret = pmic_bus_write(AXP803_ALDO1_CTRL + (aldo_num - 1), cfg);
+	if (ret)
+		return ret;
+
+	return pmic_bus_setbits(AXP803_OUTPUT_CTRL3,
+				AXP803_OUTPUT_CTRL3_ALDO1_EN << (aldo_num - 1));
+}
+
+/* TODO: re-work other AXP drivers to consolidate ALDO functions. */
+int axp_set_aldo1(unsigned int mvolt)
+{
+	return axp_set_aldo(1, mvolt);
+}
+
+int axp_set_aldo2(unsigned int mvolt)
+{
+	return axp_set_aldo(2, mvolt);
+}
+
+int axp_set_aldo3(unsigned int mvolt)
+{
+	return axp_set_aldo(3, mvolt);
+}
+
+int axp_set_dldo(int dldo_num, unsigned int mvolt)
+{
+	int ret;
+	u8 cfg;
+
+	if (dldo_num < 1 || dldo_num > 4)
+		return -EINVAL;
+
+	if (mvolt == 0)
+		return pmic_bus_clrbits(AXP803_OUTPUT_CTRL2,
+				AXP803_OUTPUT_CTRL2_DLDO1_EN << (dldo_num - 1));
+
+	cfg = axp803_mvolt_to_cfg(mvolt, 700, 3300, 100);
+	if (dldo_num == 2 && mvolt > 3300)
+		cfg += 1 + axp803_mvolt_to_cfg(mvolt, 3400, 4200, 200);
+	ret = pmic_bus_write(AXP803_DLDO1_CTRL + (dldo_num - 1), cfg);
+	if (ret)
+		return ret;
+
+	return pmic_bus_setbits(AXP803_OUTPUT_CTRL2,
+				AXP803_OUTPUT_CTRL2_DLDO1_EN << (dldo_num - 1));
+}
+
+int axp_set_eldo(int eldo_num, unsigned int mvolt)
+{
+	int ret;
+	u8 cfg;
+
+	if (eldo_num < 1 || eldo_num > 3)
+		return -EINVAL;
+
+	if (mvolt == 0)
+		return pmic_bus_clrbits(AXP803_OUTPUT_CTRL2,
+				AXP803_OUTPUT_CTRL2_ELDO1_EN << (eldo_num - 1));
+
+	cfg = axp803_mvolt_to_cfg(mvolt, 700, 1900, 50);
+	ret = pmic_bus_write(AXP803_ELDO1_CTRL + (eldo_num - 1), cfg);
+	if (ret)
+		return ret;
+
+	return pmic_bus_setbits(AXP803_OUTPUT_CTRL2,
+				AXP803_OUTPUT_CTRL2_ELDO1_EN << (eldo_num - 1));
+}
+
+int axp_set_fldo(int fldo_num, unsigned int mvolt)
+{
+	int ret;
+	u8 cfg;
+
+	if (fldo_num < 1 || fldo_num > 2)
+		return -EINVAL;
+
+	if (mvolt == 0)
+		return pmic_bus_clrbits(AXP803_OUTPUT_CTRL3,
+				AXP803_OUTPUT_CTRL3_FLDO1_EN << (fldo_num - 1));
+
+	cfg = axp803_mvolt_to_cfg(mvolt, 700, 1450, 50);
+	ret = pmic_bus_write(AXP803_FLDO1_CTRL + (fldo_num - 1), cfg);
+	if (ret)
+		return ret;
+
+	return pmic_bus_setbits(AXP803_OUTPUT_CTRL3,
+				AXP803_OUTPUT_CTRL3_FLDO1_EN << (fldo_num - 1));
+}
+
+int axp_set_sw(bool on)
+{
+	if (on)
+		return pmic_bus_setbits(AXP803_OUTPUT_CTRL2,
+					AXP803_OUTPUT_CTRL2_SW_EN);
+
+	return pmic_bus_clrbits(AXP803_OUTPUT_CTRL2,
+				AXP803_OUTPUT_CTRL2_SW_EN);
+}
+
+int axp_init(void)
+{
+	u8 axp_chip_id;
+	int ret;
+
+	ret = pmic_bus_init();
+	if (ret)
+		return ret;
+
+	ret = pmic_bus_read(AXP803_CHIP_ID, &axp_chip_id);
+	if (ret)
+		return ret;
+
+	if (!(axp_chip_id == 0x51))
+		return -ENODEV;
+	else
+		return ret;
+
+	return 0;
+}
+
+int do_poweroff(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+	pmic_bus_write(AXP803_SHUTDOWN, AXP803_SHUTDOWN_POWEROFF);
+
+	/* infinite loop during shutdown */
+	while (1) {}
+
+	/* not reached */
+	return 0;
+}
diff --git a/drivers/power/axp818.c b/drivers/power/axp818.c
index af4d7a6903..ad0c330ca5 100644
--- a/drivers/power/axp818.c
+++ b/drivers/power/axp818.c
@@ -162,7 +162,7 @@ int axp_set_dldo(int dldo_num, unsigned int mvolt)
    cfg = axp818_mvolt_to_cfg(mvolt, 700, 3300, 100);
    if (dldo_num == 2 && mvolt > 3300)
    	cfg += 1 + axp818_mvolt_to_cfg(mvolt, 3400, 4200, 200);
-	ret = pmic_bus_write(AXP818_ELDO1_CTRL + (dldo_num - 1), cfg);
+	ret = pmic_bus_write(AXP818_DLDO1_CTRL + (dldo_num - 1), cfg);
    if (ret)
    	return ret;
diff --git a/include/axp803.h b/include/axp803.h
new file mode 100644
index 0000000000..b382f3a5ec
--- /dev/null
+++ b/include/axp803.h
@@ -0,0 +1,73 @@
+/*
+ * (C) Copyright 2016 Icenowy Zheng icenowy@aosc.xyz
+ *
+ * Based on axp818.h, which is:
+ * (C) Copyright 2015 Vishnu Patekar vishnupatekar0510@gmail.com
+ *
+ * X-Powers AXP803 Power Management IC driver
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#define AXP803_CHIP_ID		0x03
+
+#define AXP803_OUTPUT_CTRL1	0x10
+#define AXP803_OUTPUT_CTRL1_DCDC1_EN	(1 << 0)
+#define AXP803_OUTPUT_CTRL1_DCDC2_EN	(1 << 1)
+#define AXP803_OUTPUT_CTRL1_DCDC3_EN	(1 << 2)
+#define AXP803_OUTPUT_CTRL1_DCDC4_EN	(1 << 3)
+#define AXP803_OUTPUT_CTRL1_DCDC5_EN	(1 << 4)
+#define AXP803_OUTPUT_CTRL1_DCDC6_EN	(1 << 5)
+#define AXP803_OUTPUT_CTRL2	0x12
+#define AXP803_OUTPUT_CTRL2_ELDO1_EN	(1 << 0)
+#define AXP803_OUTPUT_CTRL2_ELDO2_EN	(1 << 1)
+#define AXP803_OUTPUT_CTRL2_ELDO3_EN	(1 << 2)
+#define AXP803_OUTPUT_CTRL2_DLDO1_EN	(1 << 3)
+#define AXP803_OUTPUT_CTRL2_DLDO2_EN	(1 << 4)
+#define AXP803_OUTPUT_CTRL2_DLDO3_EN	(1 << 5)
+#define AXP803_OUTPUT_CTRL2_DLDO4_EN	(1 << 6)
+#define AXP803_OUTPUT_CTRL2_SW_EN	(1 << 7)
+#define AXP803_OUTPUT_CTRL3	0x13
+#define AXP803_OUTPUT_CTRL3_FLDO1_EN	(1 << 2)
+#define AXP803_OUTPUT_CTRL3_FLDO2_EN	(1 << 3)
+#define AXP803_OUTPUT_CTRL3_ALDO1_EN	(1 << 5)
+#define AXP803_OUTPUT_CTRL3_ALDO2_EN	(1 << 6)
+#define AXP803_OUTPUT_CTRL3_ALDO3_EN	(1 << 7)
+
+#define AXP803_DLDO1_CTRL	0x15
+#define AXP803_DLDO2_CTRL	0x16
+#define AXP803_DLDO3_CTRL	0x17
+#define AXP803_DLDO4_CTRL	0x18
+#define AXP803_ELDO1_CTRL	0x19
+#define AXP803_ELDO2_CTRL	0x1a
+#define AXP803_ELDO3_CTRL	0x1b
+#define AXP803_FLDO1_CTRL	0x1c
+#define AXP803_FLDO2_CTRL	0x1d
+#define AXP803_DCDC1_CTRL	0x20
+#define AXP803_DCDC2_CTRL	0x21
+#define AXP803_DCDC3_CTRL	0x22
+#define AXP803_DCDC4_CTRL	0x23
+#define AXP803_DCDC5_CTRL	0x24
+#define AXP803_DCDC6_CTRL	0x25
+
+#define AXP803_ALDO1_CTRL	0x28
+#define AXP803_ALDO2_CTRL	0x29
+#define AXP803_ALDO3_CTRL	0x2a
+
+#define AXP803_SHUTDOWN		0x32
+#define AXP803_SHUTDOWN_POWEROFF	(1 << 7)
+
+/* For axp_gpio.c */
+#define AXP_POWER_STATUS		0x00
+#define AXP_POWER_STATUS_VBUS_PRESENT		(1 << 5)
+#define AXP_VBUS_IPSOUT			0x30
+#define AXP_VBUS_IPSOUT_DRIVEBUS		(1 << 2)
+#define AXP_MISC_CTRL			0x8f
+#define AXP_MISC_CTRL_N_VBUSEN_FUNC		(1 << 4)
+#define AXP_GPIO0_CTRL			0x90
+#define AXP_GPIO1_CTRL			0x92
+#define AXP_GPIO_CTRL_OUTPUT_LOW	0x00 /* Drive pin low */
+#define AXP_GPIO_CTRL_OUTPUT_HIGH	0x01 /* Drive pin high */
+#define AXP_GPIO_CTRL_INPUT		0x02 /* Input */
+#define AXP_GPIO_STATE			0x94
+#define AXP_GPIO_STATE_OFFSET		0
diff --git a/include/axp_pmic.h b/include/axp_pmic.h
index d789ad8086..8cb4d5763c 100644
--- a/include/axp_pmic.h
+++ b/include/axp_pmic.h
@@ -16,6 +16,9 @@
 #ifdef CONFIG_AXP221_POWER
 #include <axp221.h>
 #endif
+#ifdef CONFIG_AXP803_POWER
+#include <axp803.h>
+#endif
 #ifdef CONFIG_AXP809_POWER
 #include <axp809.h>
 #endif
-- 
2.11.0


    