On 4/28/24 00:20, Marek Vasut wrote:
This stm32mp135f-dhcor-dhsbc board is a stack of DHCOR SoM based on STM32MP135F SoC (900MHz / crypto capabilities) populated on DHSBC carrier board.
The SoM contains the following peripherals:
- STPMIC (power delivery)
- 512MB DDR3L memory
- eMMC and SDIO WiFi module
The DHSBC carrier board contains the following peripherals:
- Two RGMII Ethernet ports
- USB-A Host port, USB-C peripheral port, USB-C power supply plug
- Expansion connector
Reviewed-by: Patrice Chotard patrice.chotard@foss.st.com Signed-off-by: Marek Vasut marex@denx.de
Cc: Patrice Chotard patrice.chotard@foss.st.com Cc: Patrick Delaunay patrick.delaunay@foss.st.com Cc: u-boot@dh-electronics.com Cc: uboot-stm32@st-md-mailman.stormreply.com
V2: Add RB from Patrice
arch/arm/dts/Makefile | 1 + .../dts/stm32mp135f-dhcor-dhsbc-u-boot.dtsi | 25 ++ arch/arm/dts/stm32mp135f-dhcor-dhsbc.dts | 383 ++++++++++++++++++ arch/arm/dts/stm32mp13xx-dhcor-som.dtsi | 308 ++++++++++++++ arch/arm/dts/stm32mp13xx-dhcor-u-boot.dtsi | 55 +++ configs/stm32mp13_dhcor_defconfig | 148 +++++++ 6 files changed, 920 insertions(+) create mode 100644 arch/arm/dts/stm32mp135f-dhcor-dhsbc-u-boot.dtsi create mode 100644 arch/arm/dts/stm32mp135f-dhcor-dhsbc.dts create mode 100644 arch/arm/dts/stm32mp13xx-dhcor-som.dtsi create mode 100644 arch/arm/dts/stm32mp13xx-dhcor-u-boot.dtsi create mode 100644 configs/stm32mp13_dhcor_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 0c6f0221b77..6d4972827c8 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -1285,6 +1285,7 @@ dtb-$(CONFIG_ASPEED_AST2600) += \ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
dtb-$(CONFIG_STM32MP13X) += \
- stm32mp135f-dhcor-dhsbc.dtb \ stm32mp135f-dk.dtb
dtb-$(CONFIG_STM32MP15X) += \ diff --git a/arch/arm/dts/stm32mp135f-dhcor-dhsbc-u-boot.dtsi b/arch/arm/dts/stm32mp135f-dhcor-dhsbc-u-boot.dtsi new file mode 100644 index 00000000000..d718aae16ca --- /dev/null +++ b/arch/arm/dts/stm32mp135f-dhcor-dhsbc-u-boot.dtsi @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/*
- Copyright (C) 2024 Marek Vasut marex@denx.de
- */
+#include "stm32mp13xx-dhcor-u-boot.dtsi"
+&uart4 {
- bootph-all;
+};
+&uart4_pins_b {
- bootph-all;
- pins1 {
bootph-all;- };
- pins2 {
bootph-all;- };
+};
+&usbphyc {
- bootph-all;
+}; diff --git a/arch/arm/dts/stm32mp135f-dhcor-dhsbc.dts b/arch/arm/dts/stm32mp135f-dhcor-dhsbc.dts new file mode 100644 index 00000000000..fc1c48ad56d --- /dev/null +++ b/arch/arm/dts/stm32mp135f-dhcor-dhsbc.dts @@ -0,0 +1,383 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/*
- Copyright (C) 2024 Marek Vasut marex@denx.de
- DHCOR STM32MP13 variant:
- DHCR-STM32MP135F-C100-R051-EE-F0409-SPI4-RTC-WBT-I-01LG
- DHCOR PCB number: 718-100 or newer
- DHSBC PCB number: 719-100 or newer
- */
+/dts-v1/;
+#include <dt-bindings/regulator/st,stm32mp13-regulator.h> +#include "stm32mp135.dtsi" +#include "stm32mp13xf.dtsi" +#include "stm32mp13xx-dhcor-som.dtsi"
+/ {
- model = "DH electronics STM32MP135F DHCOR DHSBC";
- compatible = "dh,stm32mp135f-dhcor-dhsbc",
"dh,stm32mp135f-dhcor-som","st,stm32mp135";- aliases {
ethernet0 = ð1;ethernet1 = ð2;serial2 = &usart1;serial3 = &usart2;- };
- chosen {
stdout-path = "serial0:115200n8";- };
+};
+&adc_1 {
- pinctrl-names = "default";
- pinctrl-0 = <&adc1_pins_a &adc1_usb_cc_pins_b>;
- vdda-supply = <&vdd_adc>;
- vref-supply = <&vdd_adc>;
- status = "okay";
- adc1: adc@0 {
status = "okay";/** Type-C USB_PWR_CC1 & USB_PWR_CC2 on in2 & in11.* Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C:* 5 * (5.1 + 47kOhms) * 5pF => 1.3us.* Use arbitrary margin here (e.g. 5us).** The pinmux pins must be set as ANALOG, use datasheet* DS13483 Table 7. STM32MP135C/F ball definitions to* find out which 'pin name' maps to which 'additional* functions', which lists the mapping between pin and* ADC channel. In this case, PA5 maps to ADC1_INP2 and* PF13 maps to ADC1_INP11 .*/channel@2 {reg = <2>;st,min-sample-time-ns = <5000>;};channel@11 {reg = <11>;st,min-sample-time-ns = <5000>;};/* Expansion connector: INP12:pin29 */channel@12 {reg = <12>;st,min-sample-time-ns = <5000>;};- };
+};
+ð1 {
- status = "okay";
- pinctrl-0 = <ð1_rgmii_pins_a>;
- pinctrl-1 = <ð1_rgmii_sleep_pins_a>;
- pinctrl-names = "default", "sleep";
- phy-mode = "rgmii-id";
- phy-handle = <ðphy1>;
- st,ext-phyclk;
- nvmem-cells = <ðernet_mac1_address>;
- nvmem-cell-names = "mac-address";
- mdio1 {
#address-cells = <1>;#size-cells = <0>;compatible = "snps,dwmac-mdio";ethphy1: ethernet-phy@1 {/* RTL8211F */compatible = "ethernet-phy-id001c.c916","ethernet-phy-ieee802.3-c22";interrupt-parent = <&gpiog>;interrupts = <12 IRQ_TYPE_LEVEL_LOW>;reg = <1>;reset-assert-us = <15000>;reset-deassert-us = <55000>;reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>;};- };
+};
+ð2 {
- status = "okay";
- pinctrl-0 = <ð2_rgmii_pins_a>;
- pinctrl-1 = <ð2_rgmii_sleep_pins_a>;
- pinctrl-names = "default", "sleep";
- phy-mode = "rgmii-id";
- phy-handle = <ðphy2>;
- st,ext-phyclk;
- nvmem-cells = <ðernet_mac2_address>;
- nvmem-cell-names = "mac-address";
- mdio1 {
#address-cells = <1>;#size-cells = <0>;compatible = "snps,dwmac-mdio";ethphy2: ethernet-phy@1 {/* RTL8211F */compatible = "ethernet-phy-id001c.c916","ethernet-phy-ieee802.3-c22";interrupt-parent = <&gpiog>;interrupts = <15 IRQ_TYPE_LEVEL_LOW>;reg = <1>;reset-assert-us = <15000>;reset-deassert-us = <55000>;reset-gpios = <&gpiog 8 GPIO_ACTIVE_LOW>;};- };
+};
+&gpioa {
- gpio-line-names = "", "", "", "",
"", "DHSBC_USB_PWR_CC1", "", "","", "", "", "DHSBC_nETH1_RST","", "DHCOR_HW-CODING_0", "", "";+};
+&gpiob {
- gpio-line-names = "", "", "", "",
"", "", "", "DHCOR_BT_HOST_WAKE","", "", "", "","", "DHSBC_nTPM_CS", "", "";+};
+&gpioc {
- gpio-line-names = "", "", "", "DHSBC_USB_5V_MEAS",
"", "", "", "","", "", "", "","", "", "", "";+};
+&gpiod {
- gpio-line-names = "", "", "", "",
"", "DHCOR_RAM-CODING_0", "", "","", "DHCOR_RAM-CODING_1", "", "","", "", "", "";+};
+&gpioe {
- gpio-line-names = "", "", "", "",
"", "", "", "","", "DHSBC_nTPM_RST", "", "","DHSBC_nTPM_PIRQ", "", "DHCOR_WL_HOST_WAKE", "";+};
+&gpiof {
- gpio-line-names = "", "", "DHSBC_USB_PWR_nFLT", "",
"", "", "", "","", "", "", "","DHCOR_WL_REG_ON", "DHSBC_USB_PWR_CC2", "", "";+};
+&gpiog {
- gpio-line-names = "", "", "", "",
"", "", "", "","DHSBC_nETH2_RST", "DHCOR_BT_DEV_WAKE", "", "","DHSBC_ETH1_INTB", "", "", "DHSBC_ETH2_INTB";+};
+&gpioi {
- gpio-line-names = "DHCOR_RTC_nINT", "DHCOR_HW-CODING_1",
"DHCOR_BT_REG_ON", "DHCOR_PMIC_nINT","DHSBC_BOOT0", "DHSBC_BOOT1","DHSBC_BOOT2", "DHSBC_USB-C_DATA_VBUS";+};
+&i2c1 { /* Expansion connector: SDA:pin27 SCL:pin28 */
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&i2c1_pins_a>;
- pinctrl-1 = <&i2c1_sleep_pins_a>;
- i2c-scl-rising-time-ns = <96>;
- i2c-scl-falling-time-ns = <3>;
- clock-frequency = <400000>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
+};
+&i2c5 { /* Expansion connector: SDA:pin3 SCL:pin5 */
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&i2c5_pins_b>;
- pinctrl-1 = <&i2c5_sleep_pins_b>;
- i2c-scl-rising-time-ns = <96>;
- i2c-scl-falling-time-ns = <3>;
- clock-frequency = <400000>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
+};
+&m_can1 { /* Expansion connector: TX:pin16 RX:pin18 */
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&m_can1_pins_a>;
- pinctrl-1 = <&m_can1_sleep_pins_a>;
- status = "okay";
+};
+&m_can2 { /* Expansion connector: TX:pin22 RX:pin26 */
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&m_can2_pins_a>;
- pinctrl-1 = <&m_can2_sleep_pins_a>;
- status = "okay";
+};
+&pwr_regulators {
- vdd-supply = <&vdd>;
- vdd_3v3_usbfs-supply = <&vdd_usb>;
- status = "okay";
+};
+&sai1 { /* Expansion connector: SCK-A:pin12 FS-A:pin35 SD-A:pin38 SD-B:pin40 */
- clocks = <&rcc SAI1>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
- clock-names = "pclk", "x8k", "x11k";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sai1a_pins_a &sai1b_pins_a>;
- pinctrl-1 = <&sai1a_sleep_pins_a &sai1b_sleep_pins_a>;
+};
+&scmi_voltd {
- status = "disabled";
+};
+&spi2 {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&spi2_pins_a>;
- pinctrl-1 = <&spi2_sleep_pins_a>;
- cs-gpios = <&gpiob 13 0>;
- status = "okay";
- st33htph: tpm@0 {
compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi";reg = <0>;spi-max-frequency = <24000000>;- };
+};
+&spi3 { /* Expansion connector: MOSI:pin19 MISO:pin21 SCK:pin22 nCS:pin24 */
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&spi3_pins_a>;
- pinctrl-1 = <&spi3_sleep_pins_a>;
- cs-gpios = <&gpiof 3 0>;
- status = "disabled";
+};
+&timers5 { /* Expansion connector: CH3:pin31 */
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
- pwm {
pinctrl-0 = <&pwm5_pins_a>;pinctrl-1 = <&pwm5_sleep_pins_a>;pinctrl-names = "default", "sleep";status = "okay";- };
- timer@4 {
status = "okay";- };
+};
+&timers13 { /* Expansion connector: CH1:pin32 */
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
- pwm {
pinctrl-0 = <&pwm13_pins_a>;pinctrl-1 = <&pwm13_sleep_pins_a>;pinctrl-names = "default", "sleep";status = "okay";- };
- timer@12 {
status = "okay";- };
+};
+&usart1 { /* Expansion connector: RX:pin33 TX:pin37 */
- pinctrl-names = "default", "sleep", "idle";
- pinctrl-0 = <&usart1_pins_b>;
- pinctrl-1 = <&usart1_sleep_pins_b>;
- pinctrl-2 = <&usart1_idle_pins_b>;
- status = "okay";
+};
+&usart2 { /* Expansion connector: RX:pin10 TX:pin8 RTS:pin11 CTS:pin36 */
- pinctrl-names = "default", "sleep", "idle";
- pinctrl-0 = <&usart2_pins_b>;
- pinctrl-1 = <&usart2_sleep_pins_b>;
- pinctrl-2 = <&usart2_idle_pins_b>;
- uart-has-rtscts;
- status = "okay";
+};
+&usbh_ehci {
- phys = <&usbphyc_port0>;
- status = "okay";
+};
+&usbh_ohci {
- phys = <&usbphyc_port0>;
- status = "okay";
+};
+&usbotg_hs {
- dr_mode = "peripheral";
- phys = <&usbphyc_port1 0>;
- phy-names = "usb2-phy";
- usb33d-supply = <&usb33>;
- status = "okay";
+};
+&usbphyc {
- status = "okay";
- vdda1v1-supply = <®11>;
- vdda1v8-supply = <®18>;
+};
+&usbphyc_port0 {
- phy-supply = <&vdd_usb>;
- st,current-boost-microamp = <1000>;
- st,decrease-hs-slew-rate;
- st,tune-hs-dc-level = <2>;
- st,enable-hs-rftime-reduction;
- st,trim-hs-current = <11>;
- st,trim-hs-impedance = <2>;
- st,tune-squelch-level = <1>;
- st,enable-hs-rx-gain-eq;
- st,no-hs-ftime-ctrl;
- st,no-lsfs-sc;
- connector {
compatible = "usb-a-connector";vbus-supply = <&vbus_sw>;- };
+};
+&usbphyc_port1 {
- phy-supply = <&vdd_usb>;
- st,current-boost-microamp = <1000>;
- st,decrease-hs-slew-rate;
- st,tune-hs-dc-level = <2>;
- st,enable-hs-rftime-reduction;
- st,trim-hs-current = <11>;
- st,trim-hs-impedance = <2>;
- st,tune-squelch-level = <1>;
- st,enable-hs-rx-gain-eq;
- st,no-hs-ftime-ctrl;
- st,no-lsfs-sc;
- connector {
compatible = "gpio-usb-b-connector", "usb-b-connector";vbus-gpios = <&gpioi 7 GPIO_ACTIVE_HIGH>;label = "Type-C";self-powered;type = "micro";- };
+}; diff --git a/arch/arm/dts/stm32mp13xx-dhcor-som.dtsi b/arch/arm/dts/stm32mp13xx-dhcor-som.dtsi new file mode 100644 index 00000000000..ddad6497775 --- /dev/null +++ b/arch/arm/dts/stm32mp13xx-dhcor-som.dtsi @@ -0,0 +1,308 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/*
- Copyright (C) 2024 Marek Vasut marex@denx.de
- */
+#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/mfd/st,stpmic1.h> +#include <dt-bindings/regulator/st,stm32mp13-regulator.h> +#include "stm32mp13-pinctrl.dtsi"
+/ {
- model = "DH electronics STM32MP13xx DHCOR SoM";
- compatible = "dh,stm32mp131a-dhcor-som",
"st,stm32mp131";- aliases {
mmc0 = &sdmmc2;mmc1 = &sdmmc1;serial0 = &uart4;serial1 = &uart7;rtc0 = &rv3032;spi0 = &qspi;- };
- memory@c0000000 {
device_type = "memory";reg = <0xc0000000 0x20000000>;- };
- reserved-memory {
#address-cells = <1>;#size-cells = <1>;ranges;optee@dd000000 {reg = <0xdd000000 0x3000000>;no-map;};- };
- sdio_pwrseq: sdio-pwrseq {
compatible = "mmc-pwrseq-simple";reset-gpios = <&gpiof 12 GPIO_ACTIVE_LOW>;- };
- vin: vin {
compatible = "regulator-fixed";regulator-name = "vin";regulator-min-microvolt = <5000000>;regulator-max-microvolt = <5000000>;regulator-always-on;- };
+};
+&i2c3 {
- i2c-scl-rising-time-ns = <96>;
- i2c-scl-falling-time-ns = <3>;
- clock-frequency = <400000>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
- pmic: stpmic@33 {
compatible = "st,stpmic1";reg = <0x33>;interrupts-extended = <&gpioi 3 IRQ_TYPE_EDGE_FALLING>;interrupt-controller;#interrupt-cells = <2>;status = "okay";regulators {compatible = "st,stpmic1-regulators";ldo1-supply = <&vin>;ldo2-supply = <&vin>;ldo3-supply = <&vin>;ldo4-supply = <&vin>;ldo5-supply = <&vin>;ldo6-supply = <&vin>;pwr_sw1-supply = <&bst_out>;pwr_sw2-supply = <&bst_out>;vddcpu: buck1 { /* VDD_CPU_1V2 */regulator-name = "vddcpu";regulator-min-microvolt = <1250000>;regulator-max-microvolt = <1250000>;regulator-always-on;regulator-initial-mode = <0>;regulator-over-current-protection;};vdd_ddr: buck2 { /* VDD_DDR_1V35 */regulator-name = "vdd_ddr";regulator-min-microvolt = <1350000>;regulator-max-microvolt = <1350000>;regulator-always-on;regulator-initial-mode = <0>;regulator-over-current-protection;};vdd: buck3 { /* VDD_3V3_1V8 */regulator-name = "vdd";regulator-min-microvolt = <1800000>;regulator-max-microvolt = <3300000>;regulator-always-on;regulator-initial-mode = <0>;regulator-over-current-protection;};vddcore: buck4 { /* VDD_CORE_1V2 */regulator-name = "vddcore";regulator-min-microvolt = <1250000>;regulator-max-microvolt = <1250000>;regulator-always-on;regulator-initial-mode = <0>;regulator-over-current-protection;};vdd_adc: ldo1 { /* VDD_ADC_1V8 */regulator-name = "vdd_adc";regulator-min-microvolt = <1800000>;regulator-max-microvolt = <1800000>;interrupts = <IT_CURLIM_LDO1 0>;};vdd_ldo2: ldo2 { /* LDO2_OUT_1V8 */regulator-name = "vdd_ldo2";regulator-min-microvolt = <1800000>;regulator-max-microvolt = <1800000>;interrupts = <IT_CURLIM_LDO2 0>;};vdd_ldo3: ldo3 { /* LDO3_OUT */regulator-name = "vdd_ldo3";regulator-min-microvolt = <1800000>;regulator-max-microvolt = <1800000>;interrupts = <IT_CURLIM_LDO3 0>;};vdd_usb: ldo4 { /* VDD_USB_3V3 */regulator-name = "vdd_usb";regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;interrupts = <IT_CURLIM_LDO4 0>;};vdd_sd: ldo5 { /* VDD_SD_3V3_1V8 */regulator-name = "vdd_sd";regulator-min-microvolt = <1800000>;regulator-max-microvolt = <3300000>;interrupts = <IT_CURLIM_LDO5 0>;};vdd_sd2: ldo6 { /* VDD_SD2_3V3_1V8 */regulator-name = "vdd_sd2";regulator-min-microvolt = <1800000>;regulator-max-microvolt = <3300000>;interrupts = <IT_CURLIM_LDO6 0>;};vref_ddr: vref_ddr { /* VREF_DDR_0V675 */regulator-name = "vref_ddr";regulator-always-on;};bst_out: boost { /* BST_OUT_5V2 */regulator-name = "bst_out";};vbus_otg: pwr_sw1 {regulator-name = "vbus_otg";interrupts = <IT_OCP_OTG 0>;};vbus_sw: pwr_sw2 {regulator-name = "vbus_sw";interrupts = <IT_OCP_SWOUT 0>;regulator-active-discharge = <1>;};};onkey {compatible = "st,stpmic1-onkey";interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;interrupt-names = "onkey-falling", "onkey-rising";status = "okay";};watchdog {compatible = "st,stpmic1-wdt";status = "disabled";};- };
- eeprom0: eeprom@50 {
compatible = "atmel,24c256"; /* ST M24256 */reg = <0x50>;pagesize = <64>;- };
- rv3032: rtc@51 {
compatible = "microcrystal,rv3032";reg = <0x51>;interrupts-extended = <&gpioi 0 IRQ_TYPE_EDGE_FALLING>;- };
+};
+&iwdg2 {
- timeout-sec = <32>;
- status = "okay";
+};
+&qspi {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&qspi_clk_pins_a
&qspi_bk1_pins_a&qspi_cs1_pins_a>;- pinctrl-1 = <&qspi_clk_sleep_pins_a
&qspi_bk1_sleep_pins_a&qspi_cs1_sleep_pins_a>;- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
- flash0: flash@0 {
compatible = "jedec,spi-nor";reg = <0>;spi-rx-bus-width = <4>;spi-max-frequency = <108000000>;#address-cells = <1>;#size-cells = <1>;- };
+};
+/* Console UART */ +&uart4 {
- pinctrl-names = "default", "sleep", "idle";
- pinctrl-0 = <&uart4_pins_b>;
- pinctrl-1 = <&uart4_sleep_pins_b>;
- pinctrl-2 = <&uart4_idle_pins_b>;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
+};
+/* Bluetooth */ +&uart7 {
- pinctrl-names = "default", "sleep", "idle";
- pinctrl-0 = <&uart7_pins_a>;
- pinctrl-1 = <&uart7_sleep_pins_a>;
- pinctrl-2 = <&uart7_idle_pins_a>;
- uart-has-rtscts;
- status = "okay";
- bluetooth {
compatible = "infineon,cyw43439-bt", "brcm,bcm4329-bt";max-speed = <3000000>;device-wakeup-gpios = <&gpiog 9 GPIO_ACTIVE_HIGH>;shutdown-gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>;- };
+};
+/* SDIO WiFi */ +&sdmmc1 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_clk_pins_a>;
- pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_clk_pins_a>;
- pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
- bus-width = <4>;
- cap-power-off-card;
- keep-power-in-suspend;
- non-removable;
- st,neg-edge;
- vmmc-supply = <&vdd>;
- mmc-pwrseq = <&sdio_pwrseq>;
- status = "okay";
- #address-cells = <1>;
- #size-cells = <0>;
- brcmf: bcrmf@1 { /* muRata 1YN */
reg = <1>;compatible = "infineon,cyw43439-fmac", "brcm,bcm4329-fmac";interrupt-parent = <&gpioe>;interrupts = <14 IRQ_TYPE_LEVEL_LOW>;interrupt-names = "host-wake";- };
+};
+/* eMMC */ +&sdmmc2 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>;
- pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>;
- pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
- bus-width = <8>;
- mmc-ddr-3_3v;
- no-sd;
- no-sdio;
- non-removable;
- st,neg-edge;
- vmmc-supply = <&vdd>;
- vqmmc-supply = <&vdd>;
- status = "okay";
+}; diff --git a/arch/arm/dts/stm32mp13xx-dhcor-u-boot.dtsi b/arch/arm/dts/stm32mp13xx-dhcor-u-boot.dtsi new file mode 100644 index 00000000000..30e3b91bccc --- /dev/null +++ b/arch/arm/dts/stm32mp13xx-dhcor-u-boot.dtsi @@ -0,0 +1,55 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/*
- Copyright (C) 2024 Marek Vasut marex@denx.de
- */
+#include "stm32mp13-u-boot.dtsi"
+/ {
- aliases {
eeprom0 = &eeprom0;- };
- config {
dh,ddr3-coding-gpios = <&gpiod 5 0>, <&gpiod 9 0>;dh,som-coding-gpios = <&gpioa 13 0>, <&gpioi 1 0>;- };
+};
+&flash0 {
- bootph-pre-ram;
- partitions {
compatible = "fixed-partitions";#address-cells = <1>;#size-cells = <1>;partition@0 {label = "fsbl1";reg = <0x00000000 0x00040000>;};partition@40000 {label = "fsbl2";reg = <0x00040000 0x00040000>;};partition@80000 {label = "u-boot";reg = <0x00080000 0x00360000>;};partition@3e0000 {label = "u-boot-env-a";reg = <0x003e0000 0x00010000>;};partition@3f0000 {label = "u-boot-env-b";reg = <0x003f0000 0x00010000>;};- };
+};
+&sdmmc1 {
- status = "disabled";
+};
+&usbotg_hs {
- u-boot,force-b-session-valid;
+}; diff --git a/configs/stm32mp13_dhcor_defconfig b/configs/stm32mp13_dhcor_defconfig new file mode 100644 index 00000000000..fb3d86deb64 --- /dev/null +++ b/configs/stm32mp13_dhcor_defconfig @@ -0,0 +1,148 @@ +CONFIG_ARM=y +CONFIG_ARCH_STM32MP=y +CONFIG_TFABOOT=y +CONFIG_SYS_MALLOC_F_LEN=0x1c0000 +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc0400000 +CONFIG_ENV_SIZE=0x4000 +CONFIG_ENV_OFFSET=0x3E0000 +CONFIG_ENV_SECT_SIZE=0x1000 +CONFIG_DEFAULT_DEVICE_TREE="stm32mp135f-dhcor-dhsbc" +CONFIG_STM32MP13X=y +CONFIG_DDR_CACHEABLE_SIZE=0x8000000 +CONFIG_CMD_STM32KEY=y +CONFIG_TARGET_ST_STM32MP13X=y +CONFIG_ENV_OFFSET_REDUND=0x3F0000 +CONFIG_CMD_STM32PROG=y +CONFIG_STM32MP15_PWR=y +# CONFIG_ARMV7_NONSEC is not set +CONFIG_SYS_LOAD_ADDR=0xc2000000 +CONFIG_SYS_MEMTEST_START=0xc0000000 +CONFIG_SYS_MEMTEST_END=0xc4000000 +CONFIG_FIT=y +CONFIG_SYS_BOOTM_LEN=0x2000000 +CONFIG_DISTRO_DEFAULTS=y +CONFIG_BOOTSTAGE_RECORD_COUNT=100 +CONFIG_BOOTDELAY=3 +CONFIG_BOOTCOMMAND="run bootcmd_stm32mp" +CONFIG_SYS_CONSOLE_IS_IN_ENV=y +CONFIG_SYS_PROMPT="STM32MP> " +# CONFIG_CMD_ELF is not set +CONFIG_CMD_ASKENV=y +# CONFIG_CMD_EXPORTENV is not set +CONFIG_CMD_ERASEENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_UNZIP=y +CONFIG_CMD_CLK=y +CONFIG_CMD_DFU=y +CONFIG_CMD_FUSE=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_LSBLK=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SPI=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_CAT=y +CONFIG_CMD_SETEXPR_FMT=y +CONFIG_CMD_XXD=y +CONFIG_CMD_DHCP6=y +CONFIG_CMD_TFTPPUT=y +CONFIG_SYS_DISABLE_AUTOLOAD=y +CONFIG_CMD_WGET=y +CONFIG_CMD_BOOTCOUNT=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_TIME=y +CONFIG_CMD_RNG=y +CONFIG_CMD_TIMER=y +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +CONFIG_CMD_BTRFS=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_LOG=y +CONFIG_CMD_UBI=y +# CONFIG_ISO_PARTITION is not set +CONFIG_OF_LIVE=y +CONFIG_ENV_IS_NOWHERE=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_ENV_SPI_MAX_HZ=50000000 +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_VERSION_VARIABLE=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_IP_DEFRAG=y +CONFIG_TFTP_TSIZE=y +CONFIG_PROT_TCP_SACK=y +CONFIG_IPV6=y +CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_SYS_BOOTCOUNT_MAGIC=0xB0C40000 +CONFIG_CLK_SCMI=y +CONFIG_SET_DFU_ALT_INFO=y +CONFIG_GPIO_HOG=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_STM32F7=y +CONFIG_LED=y +CONFIG_LED_GPIO=y +CONFIG_STM32_FMC2_EBI=y +CONFIG_I2C_EEPROM=y +CONFIG_SYS_I2C_EEPROM_ADDR=0x50 +CONFIG_SUPPORT_EMMC_BOOT=y +CONFIG_STM32_SDMMC2=y +CONFIG_MTD=y +CONFIG_DM_MTD=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_PHY_REALTEK=y +CONFIG_DWC_ETH_QOS=y +CONFIG_PHY=y +CONFIG_PHY_STM32_USBPHYC=y +CONFIG_PINCONF=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_STPMIC1=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_DM_REGULATOR_STPMIC1=y +CONFIG_DM_REGULATOR_SCMI=y +CONFIG_RESET_SCMI=y +CONFIG_DM_RNG=y +CONFIG_RNG_STM32=y +CONFIG_DM_RTC=y +CONFIG_RTC_STM32=y +CONFIG_SERIAL_RX_BUFFER=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_STM32_QSPI=y +CONFIG_STM32_SPI=y +CONFIG_SYSRESET_PSCI=y +CONFIG_TEE=y +CONFIG_OPTEE=y +# CONFIG_OPTEE_TA_AVB is not set +CONFIG_USB=y +CONFIG_DM_USB_GADGET=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_GENERIC=y +CONFIG_USB_DWC2=y +CONFIG_USB_ONBOARD_HUB=y +CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2000 +CONFIG_USB_HOST_ETHER=y +CONFIG_USB_ETHER_ASIX=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="dh" +CONFIG_USB_GADGET_VENDOR_NUM=0x0483 +CONFIG_USB_GADGET_PRODUCT_NUM=0x5720 +CONFIG_USB_GADGET_DWC2_OTG=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_WDT=y +CONFIG_WDT_STM32MP=y +CONFIG_FAT_WRITE=y +CONFIG_ERRNO_STR=y +# CONFIG_EFI_LOADER is not set
Applied to u-boot-stm32/next
Thanks Patrice