Hi,
On 21-03-16 11:06, Chen-Yu Tsai wrote:
Hi,
On Mon, Mar 21, 2016 at 5:57 PM, Hans de Goede hdegoede@redhat.com wrote:
HI,
On 21-03-16 10:49, wens Tsai wrote:
Hi Hans,
I updated U-boot on my boards to your latest sunxi-wip branch:
f965340 ("sunxi: Enable support for the eMMC found on the orangepiplus")
My Hummingbird A31 fails to boot after this. See log:
HELLO! BOOT0 is starting! boot0 version : 3.0.0 reg_addr 0x01f00100 =0x00000000 reg_addr 0x01f00104 =0x00000000 reg_addr 0x01f00108 =0x00000000 reg_addr 0x01f0010c =0x00000000 reg_addr 0x01f00110 =0x00000000 reg_addr 0x01f00114 =0x00000000 [DRAM]ver 1.03 clk = 312 cpu 0 pmu 0 dram size =1024 sum=0x31776fa8 src_sum=0x31776fa8 Ready to disable icache. Jump to secend Boot. [ 0.209]
U-Boot 2011.09-rc1 (Jun 17 2014 - 17:30:56) Allwinner Technology
[ 0.217]version: 1.1.0 [ 0.220]pmbus: ready [ 0.222]PMU: AXP221 [ 0.225]PMU: AXP22x found [ 0.227]PMU: bat ratio = 100 [ 0.231]PMU: dcdc3 1260 [ 0.233]PMU: pll1 1008 Mhz dcdc1_vol = 3000 dcdc2_vol = 1200 dcdc3_vol = 1260 dcdc4_vol = 1200 dcdc5_vol = 1500 aldo1_vol = 3000 aldo2_vol = 1800 aldo3_vol = 3000 eldo3_vol = 1800 find power_sply to end fel key old mode run key detect no key found no key input dram_para_set start dram_para_set end [ 0.277]DRAM: 1 GiB relocation Offset is: 15b25000 donn't initialize ther user_gpio (main_key:boot_init_gpio) deu_mode1 not exist. lcdgamma4iep for lcd1 not exist. DRV_DISP_Init: opened [ 0.542]fetch script data boot_disp.output_type fail [ 0.547]fetch script data boot_disp.output_mode fail [ 0.552]fetch script data boot_disp.auto_hpd fail [ 0.557]lcd0_para.lcd_used=1 workmode = 0 [ 0.603]NAND: NAND_UbootInit NB1 : enter NAND_LogicInit not burn nand partition table! NB1 : nftl num: 2 init nftl: 0 NB1 : NAND_LogicInit ok, result = 0x0 [ 1.268]sunxi flash init ok probe mmc0 if exist SUNXI SD/MMC: 0 Man 1d4144 Snr d3602657 SD 0.2 boot0 capacity: 0KB,boot1 capacity: 0KB boot0 magic = eGON.BT0蜡讕 set next system status DRV_DISP_Exit: closed sunxi_board_close_source NAND_UbootExit NB1 : NAND_LogicExit reset cpu HELLO! BOOT0 is starting! boot0 version : 3.0.0 reg_addr 0x01f00100 =0x00007347 reg_addr 0x01f00104 =0x0000703b reg_addr 0x01f00108 =0x5aa5a55a reg_addr 0x01f0010c =0x000000ff reg_addr 0x01f00110 =0x000000ff reg_addr 0x01f00114 =0x000000ff eraly jump fel
U-Boot SPL 2016.03-00320-geeea041 (Mar 21 2016 - 15:16:34) DRAM: 1024 MiB Trying to boot from MMC1
and hangs...
geeea041 is the SinA31s patch I have on top of your sunxi-wip branch.
I bisected it down to 107fb76 ("sunxi: Fix gmac not working due to cpu_eth_init no longer being called"). Not sure why this commit fails though.
Hmm, can you try commenting out these 2 lines in arch/arm/cpu/armv7/sunxi/board.c :
#ifdef CONFIG_MACPWR gpio_request(CONFIG_MACPWR, "macpwr"); gpio_direction_output(CONFIG_MACPWR, 1); #endif
Around line 103 ? That is the only bit which has changed in the SPL path due to this patch.
This fixes the problem. Thanks.
I'm guessing it's a bad idea to call the generic GPIO functions, which are DM based, in SPL?
When building the SPL CONFIG_DM_GPIO is not set, and there are non DM implementations for the SPL in drivers/gpio/sunxi_gpio.c
So the functions should work, and the fact that you get to
"Trying to boot from MMC1"
Shows that at least the SPL does not crash at this code, because that is done way earlier (before the first message is printed on the serial console, the same function also sets up the uart muxing).
So I do not believe that the problem is actually calling the gpio_request() (nop in non DM mode) nor gpio_direction_output() in general.
Which would lead to the conclusion that the problem is the changing of the gpio pin value before u-boot proper has loaded, which is a bit weird.
Note that commenting out these lines will likely lead to a non working ethernet on the board. If it does not then you do not need CONFIG_MACPWR and it could be that you're driving some $random pin high causing issues.
If the commenting out does lead to a non working ethernet we could try to fix things by changing the #ifdef to:
#if !defined CONFIG_SPL_BUILD && defined CONFIG_MACPWR
Which would cause us to only turn on the gpio when initializing gpio-s in u-boot proper and not in the SPL.
Regards,
Hans