Rework kernel-doc comments in dwmmc.h header so it's actually possible to generate a proper documentation from it usin scripts/kernel-doc script, with no errors.
No functional change.
Signed-off-by: Sam Protsenko semen.protsenko@linaro.org --- include/dwmmc.h | 41 ++++++++++++++++++++++------------------- 1 file changed, 22 insertions(+), 19 deletions(-)
diff --git a/include/dwmmc.h b/include/dwmmc.h index 7bb456e792b4..77c8989148a1 100644 --- a/include/dwmmc.h +++ b/include/dwmmc.h @@ -182,6 +182,7 @@ struct dwmci_idmac_regs { * @ioaddr: Base I/O address of controller * @quirks: Quick flags - see DWMCI_QUIRK_... * @caps: Capabilities - see MMC_MODE_... + * @clock: Current clock frequency (after internal divider), Hz * @bus_hz: Bus speed in Hz, if @get_mmc_clk() is NULL * @div: Arbitrary clock divider value for use by controller * @dev_index: Arbitrary device index for use by controller @@ -190,6 +191,10 @@ struct dwmci_idmac_regs { * @fifo_depth: Depth of FIFO, bytes (or 0 for automatic detection) * @mmc: Pointer to generic MMC structure for this device * @priv: Private pointer for use by controller + * @clksel: (Optional) Platform function to run when speed/width is changed + * @board_init: (Optional) Platform function to run on init + * @cfg: Internal MMC configuration, for !CONFIG_BLK cases + * @fifo_mode: Use FIFO mode (not DMA) to read and write data * @dma_64bit_address: Whether DMA supports 64-bit address mode or not * @regs: Registers that can vary for different DW MMC block versions */ @@ -210,9 +215,12 @@ struct dwmci_host {
int (*clksel)(struct dwmci_host *host); void (*board_init)(struct dwmci_host *host); - /** - * Get / set a particular MMC clock frequency + * @get_mmc_clk: (Optional) Platform function to get/set a particular + * MMC clock frequency + * + * @host: DWMMC host + * @freq: Frequency the host is trying to achieve * * This is used to request the current clock frequency of the clock * that drives the DWMMC peripheral. The caller will then use this @@ -220,16 +228,12 @@ struct dwmci_host { * required MMC bus clock frequency. If you want to handle the * clock external to DWMMC, use @freq to select the frequency and * return that value too. Then DWMMC will put itself in bypass mode. - * - * @host: DWMMC host - * @freq: Frequency the host is trying to achieve */ unsigned int (*get_mmc_clk)(struct dwmci_host *host, uint freq); #ifndef CONFIG_BLK struct mmc_config cfg; #endif
- /* use fifo mode to read and write data */ bool fifo_mode; bool dma_64bit_address; const struct dwmci_idmac_regs *regs; @@ -267,6 +271,10 @@ static inline u8 dwmci_readb(struct dwmci_host *host, int reg) #ifdef CONFIG_BLK /** * dwmci_setup_cfg() - Set up the configuration for DWMMC + * @cfg: Configuration structure to fill in (generally &plat->mmc) + * @host: DWMMC host + * @max_clk: Maximum supported clock speed in Hz (e.g. 150000000) + * @min_clk: Minimum supported clock speed in Hz (e.g. 400000) * * This is used to set up a DWMMC device when you are using CONFIG_BLK. * @@ -291,28 +299,23 @@ static inline u8 dwmci_readb(struct dwmci_host *host, int reg) * struct rockchip_mmc_plat *plat = dev_get_plat(dev); * * See rockchip_dw_mmc.c for an example. - * - * @cfg: Configuration structure to fill in (generally &plat->mmc) - * @host: DWMMC host - * @max_clk: Maximum supported clock speed in HZ (e.g. 150000000) - * @min_clk: Minimum supported clock speed in HZ (e.g. 400000) */ void dwmci_setup_cfg(struct mmc_config *cfg, struct dwmci_host *host, u32 max_clk, u32 min_clk);
/** * dwmci_bind() - Set up a new MMC block device + * @dev: Device to set up + * @mmc: Pointer to mmc structure (normally &plat->mmc) + * @cfg: Empty configuration structure (generally &plat->cfg). This is + * normally all zeroes at this point. The only purpose of passing + * this in is to set mmc->cfg to it. * * This is used to set up a DWMMC block device when you are using CONFIG_BLK. * It should be called from your driver's bind() method. * * See rockchip_dw_mmc.c for an example. * - * @dev: Device to set up - * @mmc: Pointer to mmc structure (normally &plat->mmc) - * @cfg: Empty configuration structure (generally &plat->cfg). This is - * normally all zeroes at this point. The only purpose of passing - * this in is to set mmc->cfg to it. * Return: 0 if OK, -ve if the block device could not be created */ int dwmci_bind(struct udevice *dev, struct mmc *mmc, struct mmc_config *cfg); @@ -320,12 +323,12 @@ int dwmci_bind(struct udevice *dev, struct mmc *mmc, struct mmc_config *cfg); #else /** * add_dwmci() - Add a new DWMMC interface + * @host: DWMMC host structure + * @max_clk: Maximum supported clock speed in Hz (e.g. 150000000) + * @min_clk: Minimum supported clock speed in Hz (e.g. 400000) * * This is used when you are not using CONFIG_BLK. Convert your driver over! * - * @host: DWMMC host structure - * @max_clk: Maximum supported clock speed in HZ (e.g. 150000000) - * @min_clk: Minimum supported clock speed in HZ (e.g. 400000) * Return: 0 if OK, -ve on error */ int add_dwmci(struct dwmci_host *host, u32 max_clk, u32 min_clk);