From: Haibo Chen haibo.chen@nxp.com
In current code, we add 1ms dealy after each tuning command for standard tuning method. Adding this 1ms dealy is because USDHC default check the CMD CRC and DATA line. If detect the CMD CRC, USDHC standard tuning IC logic do not wait for the tuning data sending out by the card, trigger the buffer read ready interrupt immediately, and step to next cycle. So when next time the new tuning command send out by USDHC, card may still not send out the tuning data of the upper command，then some eMMC cards may stuck, can't response to any command, block the whole tuning procedure.
If do not check the CMD CRC for tuning, then do not has this issue. USDHC will wait for the tuning data of each tuning command and check them. If the tuning data pass the check, it also means the CMD line also okay for tuning.
So this patch disable the CMD CRC check for tuning, save some time for the whole tuning procedure.
Signed-off-by: Haibo Chen haibo.chen@nxp.com --- drivers/mmc/fsl_esdhc_imx.c | 22 ++++++++++++---------- include/fsl_esdhc_imx.h | 1 + 2 files changed, 13 insertions(+), 10 deletions(-)
diff --git a/drivers/mmc/fsl_esdhc_imx.c b/drivers/mmc/fsl_esdhc_imx.c index f42e018434..5b61eeb214 100644 --- a/drivers/mmc/fsl_esdhc_imx.c +++ b/drivers/mmc/fsl_esdhc_imx.c @@ -907,19 +907,9 @@ static int fsl_esdhc_execute_tuning(struct udevice *dev, uint32_t opcode) ctrl = readl(®s->autoc12err); if ((!(ctrl & MIX_CTRL_EXE_TUNE)) && (ctrl & MIX_CTRL_SMPCLK_SEL)) { - /* - * need to wait some time, make sure sd/mmc fininsh - * send out tuning data, otherwise, the sd/mmc can't - * response to any command when the card still out - * put the tuning data. - */ - mdelay(1); ret = 0; break; } - - /* Add 1ms delay for SD and eMMC */ - mdelay(1); }
writel(irqstaten, ®s->irqstaten); @@ -1267,6 +1257,18 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv, val |= priv->tuning_start_tap; val &= ~ESDHC_TUNING_STEP_MASK; val |= (priv->tuning_step) << ESDHC_TUNING_STEP_SHIFT; + + /* Disable the CMD CRC check for tuning, if not, need to + * add some delay after every tuning command, because + * hardware standard tuning logic will directly go to next + * step once it detect the CMD CRC error, will not wait for + * the card side to finally send out the tuning data, trigger + * the buffer read ready interrupt immediately. If usdhc send + * the next tuning command some eMMC card will stuck, can't + * response, block the tuning procedure or the first command + * after the whole tuning procedure always can't get any response. + */ + val |= ESDHC_TUNING_CMD_CRC_CHECK_DISABLE; writel(val, ®s->tuning_ctrl); } } diff --git a/include/fsl_esdhc_imx.h b/include/fsl_esdhc_imx.h index 220a76b9ee..279a66d9bf 100644 --- a/include/fsl_esdhc_imx.h +++ b/include/fsl_esdhc_imx.h @@ -204,6 +204,7 @@ /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */ #define ESDHC_TUNING_START_TAP_DEFAULT 0x1 #define ESDHC_TUNING_START_TAP_MASK 0x7f +#define ESDHC_TUNING_CMD_CRC_CHECK_DISABLE BIT(7) #define ESDHC_TUNING_STEP_MASK 0x00070000 #define ESDHC_TUNING_STEP_SHIFT 16