On 2022-07-08 20:38, Tom Rini wrote:
- Remove some missed wiki markup, and escape a "\n" correctly.
- Use gender-neutral language to refer to the user, consistently.
Cc: Claudius Heine ch@denx.de Signed-off-by: Tom Rini trini@konsulko.com
doc/develop/designprinciples.rst | 28 ++++++++++++++-------------- 1 file changed, 14 insertions(+), 14 deletions(-)
diff --git a/doc/develop/designprinciples.rst b/doc/develop/designprinciples.rst index 79694db77604..b6ceff1aa02b 100644 --- a/doc/develop/designprinciples.rst +++ b/doc/develop/designprinciples.rst @@ -18,8 +18,8 @@ relatively small NOR flash memory, which is expensive compared to the much larger NAND devices often used to store the operating system and the application.
-At the moment, U-Boot supports boards with just 128 !KiB ROM or with -256 !KiB NOR flash. We should not easily ignore such configurations - +At the moment, U-Boot supports boards with just 128 KiB ROM or with +256 KiB NOR flash. We should not easily ignore such configurations - they may be the exception in among all the other supported boards, but if a design uses such a resource-constrained hardware setup it is usually because costs are critical, i. e. because the number of @@ -28,15 +28,15 @@ millions...
A usable and useful configuration of U-Boot, including a basic interactive command interpreter, support for download over Ethernet -and the capability to program the flash shall fit in no more than 128 !KiB. +and the capability to program the flash shall fit in no more than 128 KiB.
Keep it Fast ^^^^^^^^^^^^
The end user is not interested in running U-Boot. In most embedded -systems he is not even aware that U-Boot exists. The user wants to +systems they are not even aware that U-Boot exists. The user wants to run some application code, and that as soon as possible after switching -on his device. +on their device.
It is therefore essential that U-Boot is as fast as possible, especially that it loads and boots the operating system as fast as possible. @@ -62,7 +62,7 @@ Keep it Simple ^^^^^^^^^^^^^^
U-Boot is a boot loader, but it is also a tool used for board -bring-up, for production testing, and for other activities +bring-up, for production testing, and for other activities.
Keep it Portable ^^^^^^^^^^^^^^^^ @@ -95,13 +95,13 @@ Keep it Configurable Section "Keep it Small" already explains about the size restrictions for U-Boot on one side. On the other side, U-Boot is a powerful tool with many, many extremely useful features. The maintainer or user of -each board will have to decide which features are important to him and -what shall be included with his specific board configuration to meet -his current requirements and restrictions. +each board will have to decide which features are important to them and +what shall be included with their specific board configuration to meet +their current requirements and restrictions.
Please make sure that it is easy to add or remove features from a board configuration, so everybody can make the best use of U-Boot on -his system. +their system.
If a feature is not included, it should not have any residual code bloating the build. @@ -124,7 +124,7 @@ debug is all the more important to many of us.
- All initialization steps shall print some "begin doing this" message before they actually start, and some "done" message when they complete. For example, RAM initialization and size detection may print a "RAM: " before they start,
- and "256 MB\n" when done. The purpose of this is that you can always see
- and "256 MB\n" when done. The purpose of this is that you can always see which initialization step was running if there should be any problem. This is important not only during software development, but also for the service people dealing with broken hardware in the field.
@@ -140,8 +140,8 @@ Please always keep in mind that there are at least three different groups of users for U-Boot, with completely different expectations and requirements:
-* The end user of an embedded device just wants to run some application; he
- does not even want to know that U-Boot exists and only rarely interacts with
+* The end user of an embedded device just wants to run some application; they
- do not even want to know that U-Boot exists and only rarely interacts with it (for example to perform a reset to factory default settings etc.)
and/or the operating system want a powerful tool that can boot from any boot
- System designers and engineers working on the development of the application
@@ -151,7 +151,7 @@ and requirements: U-Boot to be as simple as possible so porting it to and maintaining it on their hardware is easy for them.
- Make it easy to test. Add debug code (but don't re-invent the wheel - use
- existing macros like debug() or debugX()).
existing macros like debug()).
Please always keep in mind that U-Boot tries to meet all these different requirements.
Reviewed-by: Claudius Heine ch@denx.de