Falcon mode requires a board-specific mechanism to select between fast and normal boot. This is done via spl_start_uboot()
Use the USER2 button as the selection mechanism. This is connected to GPIO PA13. This GPIO is already accessible via the "st,fastboot-gpios" devicetree node, but is is also aliased as "u-boot,falcon-gpios". This is the only button on DK2 which accessible simultaneously to the RESET button. USER2 is too close, and I can't fit my fingers to press both.
The fact that USER2 is also used for android fastboot is of no consequence. One can let go of USER2 after SPL but before being sampled by u-boot. If that is missed, it's okay, u-boot tries to initialize the ethernet, which can be stopped with a Ctr-C. This conveniently opens up a u-boot shell.
Offsets for raw MMC loading are defined. These point to the partition after "ssbl". Offsets for SPI are not defined, and thus SPL_LOAD_SPI must be disabled to avoid a build failure. The only way to accommodate this is to add a new defconfig, adventurously named stm32mp1_falcon.
The baudrate is set to 2 Mbaud, as the point of this config is to boot fast. The default devicetree is set to -dk2. This is because EV1 does not have a crypto-enabled CPU, and thus enabling ECDSA support would have made far less sense. That and all the goodies with FIT in SPL are enabled to give this config some continuous integration TLC.
Signed-off-by: Alexandru Gagniuc mr.nuke.me@gmail.com --- arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi | 2 + board/st/stm32mp1/spl.c | 39 +++++ configs/stm32mp15_falcon_defconfig | 181 +++++++++++++++++++++++ 3 files changed, 222 insertions(+) create mode 100644 configs/stm32mp15_falcon_defconfig
diff --git a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi index 0101962ea5..b314ce2dac 100644 --- a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi +++ b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi @@ -16,6 +16,8 @@ u-boot,boot-led = "heartbeat"; u-boot,error-led = "error"; u-boot,mmc-env-partition = "fip"; + /* This is the same as fastboot-gpios. This is on purpose */ + u-boot,falcon-gpios = <&gpioa 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; st,adc_usb_pd = <&adc1 18>, <&adc1 19>; st,fastboot-gpios = <&gpioa 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; st,stm32prog-gpios = <&gpioa 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; diff --git a/board/st/stm32mp1/spl.c b/board/st/stm32mp1/spl.c index 8e4549a1b3..921d0190e0 100644 --- a/board/st/stm32mp1/spl.c +++ b/board/st/stm32mp1/spl.c @@ -8,6 +8,7 @@ #include <init.h> #include <asm/io.h> #include <asm/arch/sys_proto.h> +#include <asm/gpio.h> #include <linux/bitops.h> #include <linux/delay.h> #include "../common/stpmic1.h" @@ -29,6 +30,44 @@ int board_early_init_f(void) return 0; }
+#if IS_ENABLED(CONFIG_SPL_OS_BOOT) +int spl_start_uboot(void) +{ + ofnode node; + struct gpio_desc gpio; + int boot_uboot = 1; + + node = ofnode_path("/config"); + if (!ofnode_valid(node)) { + pr_warn("%s: no /config node?\n", __func__); + return 0; + } + + if (gpio_request_by_name_nodev(node, "u-boot,falcon-gpios", 0, &gpio, + GPIOD_IS_IN)) { + pr_warn("%s: could not find a /config/u-boot,falcon-gpios\n", + __func__); + return 1; + } + + boot_uboot = dm_gpio_get_value(&gpio); + dm_gpio_free(NULL, &gpio); + + return boot_uboot; +} + +#if IS_ENABLED(CONFIG_ARMV7_NONSEC) +/* + * A bit of a hack, but armv7_boot_nonsec() is provided by bootm.c. This is not + * available in SPL, so we have to provide an implementation. + */ +bool armv7_boot_nonsec(void) +{ + return 0; +} +#endif /* CONFIG_ARMV7_NONSEC */ +#endif /* CONFIG_SPL_OS_BOOT */ + #ifdef CONFIG_DEBUG_UART_BOARD_INIT void board_debug_uart_init(void) { diff --git a/configs/stm32mp15_falcon_defconfig b/configs/stm32mp15_falcon_defconfig new file mode 100644 index 0000000000..f86ef41589 --- /dev/null +++ b/configs/stm32mp15_falcon_defconfig @@ -0,0 +1,181 @@ +CONFIG_ARM=y +CONFIG_ARCH_STM32MP=y +CONFIG_SYS_MALLOC_F_LEN=0x3000 +CONFIG_SYS_MEMTEST_START=0xc0000000 +CONFIG_SYS_MEMTEST_END=0xc4000000 +CONFIG_ENV_OFFSET=0x280000 +CONFIG_ENV_SECT_SIZE=0x40000 +CONFIG_DEFAULT_DEVICE_TREE="stm32mp157c-dk2" +CONFIG_SPL_TEXT_BASE=0x2FFC2500 +CONFIG_SPL_MMC_SUPPORT=y +CONFIG_SPL=y +CONFIG_TARGET_ST_STM32MP15x=y +CONFIG_CMD_STM32KEY=y +CONFIG_CMD_STM32PROG=y +CONFIG_ENV_OFFSET_REDUND=0x2C0000 +CONFIG_TYPEC_STUSB160X=y +# CONFIG_ARMV7_VIRT is not set +CONFIG_DISTRO_DEFAULTS=y +CONFIG_FIT=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_SPL_LOAD_FIT_APPLY_OVERLAY=y +# CONFIG_USE_SPL_FIT_GENERATOR is not set +CONFIG_BOOTDELAY=1 +CONFIG_BOOTCOMMAND="run bootcmd_stm32mp" +CONFIG_SPL_LOG=y +CONFIG_BOARD_EARLY_INIT_F=y +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3 +CONFIG_SPL_ENV_SUPPORT=y +CONFIG_SPL_I2C=y +CONFIG_SPL_MTD_SUPPORT=y +CONFIG_SPL_OS_BOOT=y +CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR=0x1422 +CONFIG_SPL_POWER=y +CONFIG_SPL_OPTEE=y +CONFIG_SYS_PROMPT="STM32MP> " +CONFIG_CMD_ADTIMG=y +CONFIG_CMD_ERASEENV=y +CONFIG_CMD_NVEDIT_EFI=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_UNZIP=y +CONFIG_CMD_ADC=y +CONFIG_CMD_CLK=y +CONFIG_CMD_DFU=y +CONFIG_CMD_FUSE=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_REMOTEPROC=y +CONFIG_CMD_SPI=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_BMP=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EFIDEBUG=y +CONFIG_CMD_TIME=y +CONFIG_CMD_RNG=y +CONFIG_CMD_TIMER=y +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_MTDPARTS=y +CONFIG_CMD_LOG=y +CONFIG_CMD_UBI=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_OF_LIVE=y +CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-extended interrupt-controller \#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks" +CONFIG_ENV_IS_NOWHERE=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_ENV_IS_IN_UBI=y +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y +CONFIG_ENV_UBI_PART="UBI" +CONFIG_ENV_UBI_VOLUME="uboot_config" +CONFIG_ENV_UBI_VOLUME_REDUND="uboot_config_r" +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_SYS_MMC_ENV_DEV=-1 +# CONFIG_SPL_ENV_IS_NOWHERE is not set +# CONFIG_SPL_ENV_IS_IN_SPI_FLASH is not set +CONFIG_STM32_ADC=y +CONFIG_SET_DFU_ALT_INFO=y +CONFIG_USB_FUNCTION_FASTBOOT=y +CONFIG_FASTBOOT_BUF_ADDR=0xC0000000 +CONFIG_FASTBOOT_BUF_SIZE=0x02000000 +CONFIG_FASTBOOT_USB_DEV=1 +CONFIG_FASTBOOT_FLASH=y +CONFIG_FASTBOOT_FLASH_MMC_DEV=1 +CONFIG_FASTBOOT_MMC_BOOT_SUPPORT=y +CONFIG_FASTBOOT_MMC_BOOT1_NAME="mmc1boot0" +CONFIG_FASTBOOT_MMC_BOOT2_NAME="mmc1boot1" +CONFIG_FASTBOOT_MMC_USER_SUPPORT=y +CONFIG_FASTBOOT_MMC_USER_NAME="mmc1" +CONFIG_FASTBOOT_CMD_OEM_FORMAT=y +CONFIG_FASTBOOT_CMD_OEM_PARTCONF=y +CONFIG_FASTBOOT_CMD_OEM_BOOTBUS=y +CONFIG_GPIO_HOG=y +CONFIG_DM_HWSPINLOCK=y +CONFIG_HWSPINLOCK_STM32=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_STM32F7=y +CONFIG_LED=y +CONFIG_LED_GPIO=y +CONFIG_DM_MAILBOX=y +CONFIG_STM32_IPCC=y +CONFIG_STM32_FMC2_EBI=y +CONFIG_SUPPORT_EMMC_BOOT=y +CONFIG_STM32_SDMMC2=y +CONFIG_MTD=y +CONFIG_DM_MTD=y +CONFIG_SYS_MTDPARTS_RUNTIME=y +CONFIG_MTD_RAW_NAND=y +CONFIG_NAND_STM32_FMC2=y +CONFIG_MTD_SPI_NAND=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_WINBOND=y +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_SPI_FLASH_MTD=y +CONFIG_PHY_REALTEK=y +CONFIG_DM_ETH=y +CONFIG_DWC_ETH_QOS=y +CONFIG_PHY=y +CONFIG_PHY_STM32_USBPHYC=y +CONFIG_PINCONF=y +# CONFIG_SPL_PINCTRL_FULL is not set +CONFIG_PINCTRL_STMFX=y +CONFIG_DM_PMIC=y +# CONFIG_SPL_PMIC_CHILDREN is not set +CONFIG_PMIC_STPMIC1=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_DM_REGULATOR_STM32_VREFBUF=y +CONFIG_DM_REGULATOR_STPMIC1=y +CONFIG_REMOTEPROC_STM32_COPRO=y +CONFIG_DM_RNG=y +CONFIG_RNG_STM32MP1=y +CONFIG_DM_RTC=y +CONFIG_RTC_STM32=y +CONFIG_BAUDRATE=2000000 +CONFIG_SERIAL_RX_BUFFER=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_STM32_QSPI=y +CONFIG_STM32_SPI=y +CONFIG_SYSRESET_CMD_POWEROFF=y +CONFIG_TEE=y +CONFIG_OPTEE=y +CONFIG_USB=y +CONFIG_DM_USB_GADGET=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="STMicroelectronics" +CONFIG_USB_GADGET_VENDOR_NUM=0x0483 +CONFIG_USB_GADGET_PRODUCT_NUM=0x5720 +CONFIG_USB_GADGET_DWC2_OTG=y +CONFIG_DM_VIDEO=y +CONFIG_BACKLIGHT_GPIO=y +CONFIG_VIDEO_LCD_ORISETECH_OTM8009A=y +CONFIG_VIDEO_LCD_RAYDIUM_RM68200=y +CONFIG_VIDEO_STM32=y +CONFIG_VIDEO_STM32_DSI=y +CONFIG_VIDEO_STM32_MAX_XRES=1280 +CONFIG_VIDEO_STM32_MAX_YRES=800 +CONFIG_VIDEO_BMP_RLE8=y +CONFIG_BMP_16BPP=y +CONFIG_BMP_24BPP=y +CONFIG_BMP_32BPP=y +CONFIG_WDT=y +CONFIG_WDT_STM32MP=y +CONFIG_ECDSA=y +CONFIG_SPL_ECDSA_VERIFY=y +CONFIG_ERRNO_STR=y +CONFIG_FDT_FIXUP_PARTITIONS=y +# CONFIG_LMB_USE_MAX_REGIONS is not set +CONFIG_LMB_MEMORY_REGIONS=2 +CONFIG_LMB_RESERVED_REGIONS=16