This patch modify the loop in mtd erase command to erase one by one the blocks in the requested area.
It solves issue on "mtd erase" command on nand with existing bad block, the command is interrupted on the first bad block with the trace: "Skipping bad block at 0xffffffffffffffff"
In MTD driver (nand/raw), when a bad block is present on the MTD device, the erase_op.fail_addr is not updated and we have the initial value MTD_FAIL_ADDR_UNKNOWN = (ULL)-1.
This case seems normal in nand_base.c:nand_erase_nand(), we have the 2 exit cases during the loop:
1/ we have a bad block (nand_block_checkbad) instr->state = MTD_ERASE_FAILED loop interrupted (goto erase_exit)
2/ if block erase failed (status & NAND_STATUS_FAIL) instr->state = MTD_ERASE_FAILED; instr->fail_addr = ((loff_t)page << chip->page_shift); loop interrupted (goto erase_exit)
So erase_op.fail_addr can't be used if bad blocks were present in the erased area; we need to use mtd_erase only one block to detect and skip these existing bad blocks (as it is done in nand_util.c).
Signed-off-by: Patrick Delaunay patrick.delaunay@st.com ---
Hi,
Found a correct in the mtd erase command.
I detect the issue and test the patch on STM32MP157C-EV1 board, with nor and nand. We have the block table at the end of the nand so the 4 last blocks are marked bad.
And I try to erase all the nand with the command "mtd erase".
Before the patch:
The "nand erase" command behavior is OK:
STM32MP> nand erase 0x0 0x000040000000
NAND erase: device 0 whole chip Skipping bad block at 0x3ff00000 Skipping bad block at 0x3ff40000 Skipping bad block at 0x3ff80000 Skipping bad block at 0x3ffc0000
But the "mtd erase" command is not correct:
STM32MP> mtd list SF: Detected mx66l51235l with page size 256 Bytes, erase size 64 KiB, total 64 MiB List of MTD devices: * nand0 - type: NAND flash - block size: 0x40000 bytes - min I/O: 0x1000 bytes - OOB size: 224 bytes - OOB available: 118 bytes - ECC strength: 8 bits - ECC step size: 512 bytes - bitflip threshold: 6 bits - 0x000000000000-0x000040000000 : "nand0" - 0x000000000000-0x000000200000 : "fsbl" - 0x000000200000-0x000000400000 : "ssbl1" - 0x000000400000-0x000000600000 : "ssbl2" - 0x000000600000-0x000040000000 : "UBI" * nor0 - type: NOR flash - block size: 0x10000 bytes - min I/O: 0x1 bytes - 0x000000000000-0x000004000000 : "nor0" - 0x000000000000-0x000000040000 : "fsbl1" - 0x000000040000-0x000000080000 : "fsbl2" - 0x000000080000-0x000000280000 : "ssbl" - 0x000000280000-0x000000300000 : "u-boot-env" - 0x000000300000-0x000004000000 : "nor_user"
STM32MP> mtd erase nand0 0x0 0x000040000000 Erasing 0x00000000 ... 0x3fffffff (4096 eraseblock(s)) Skipping bad block at 0xffffffffffffffff
OK
The 4 bad blocks are not correctly skipped, the command is stopped on the first error.
After the patch, the "mtd erase" command skips the 4 bad block exactly as the "nand erase" command:
STM32MP> mtd erase nand0 0x000000000000 0x000040000000 SF: Detected mx66l51235l with page size 256 Bytes, erase size 64 KiB, total 64 MiB Erasing 0x00000000 ... 0x3fffffff (4096 eraseblock(s)) Skipping bad block at 0x3ff00000 Skipping bad block at 0x3ff40000 Skipping bad block at 0x3ff80000 Skipping bad block at 0x3ffc0000
Regards
Patrick
cmd/mtd.c | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-)
diff --git a/cmd/mtd.c b/cmd/mtd.c index 1b6b8dda2b..a559b5a4a3 100644 --- a/cmd/mtd.c +++ b/cmd/mtd.c @@ -387,7 +387,7 @@ static int do_mtd_erase(cmd_tbl_t *cmdtp, int flag, int argc, struct mtd_info *mtd; u64 off, len; bool scrub; - int ret; + int ret = 0;
if (argc < 2) return CMD_RET_USAGE; @@ -423,22 +423,22 @@ static int do_mtd_erase(cmd_tbl_t *cmdtp, int flag, int argc,
erase_op.mtd = mtd; erase_op.addr = off; - erase_op.len = len; + erase_op.len = mtd->erasesize; erase_op.scrub = scrub;
- while (erase_op.len) { + while (len) { ret = mtd_erase(mtd, &erase_op);
- /* Abort if its not a bad block error */ - if (ret != -EIO) - break; - - printf("Skipping bad block at 0x%08llx\n", erase_op.fail_addr); + if (ret) { + /* Abort if its not a bad block error */ + if (ret != -EIO) + break; + printf("Skipping bad block at 0x%08llx\n", + erase_op.addr); + }
- /* Skip bad block and continue behind it */ - erase_op.len -= erase_op.fail_addr - erase_op.addr; - erase_op.len -= mtd->erasesize; - erase_op.addr = erase_op.fail_addr + mtd->erasesize; + len -= mtd->erasesize; + erase_op.addr += mtd->erasesize; }
if (ret && ret != -EIO)