Re: [U-Boot] [PATCH 2/3] armv8: ls1028ardb: Add support for LS1028ARDB platform

-----Original Message----- From: Bhaskar Upadhaya Sent: Monday, March 18, 2019 3:15 PM To: u-boot@lists.denx.de Cc: Prabhakar Kushwaha prabhakar.kushwaha@nxp.com; Sudhanshu Gupta sudhanshu.gupta@nxp.com; Harninder Rai harninder.rai@nxp.com; Rajesh Bhagat rajesh.bhagat@nxp.com Subject: [PATCH 2/3] armv8: ls1028ardb: Add support for LS1028ARDB platform

LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluatoin platform that supports the LS1028A family SoCs. This patch add basic support of the platform.

Signed-off-by: Sudhanshu Gupta sudhanshu.gupta@nxp.com Signed-off-by: Rai Harninder harninder.rai@nxp.com Signed-off-by: Rajesh Bhagat rajesh.bhagat@nxp.com Signed-off-by: Bhaskar Upadhaya Bhaskar.Upadhaya@nxp.com

---

arch/arm/Kconfig | 12 ++ arch/arm/cpu/armv8/Kconfig | 1 + arch/arm/dts/fsl-ls1028a-rdb.dts | 20 +++ board/freescale/ls1028a/Kconfig | 38 +++++ board/freescale/ls1028a/MAINTAINERS | 9 ++ board/freescale/ls1028a/Makefile | 8 + board/freescale/ls1028a/README | 85 +++++++++++ board/freescale/ls1028a/ddr.c | 284 ++++++++++++++++++++++++++++++++++ board/freescale/ls1028a/ddr.h | 46 ++++++ board/freescale/ls1028a/ls1028a.c | 251 ++++++++++++++++++++++++++++++ configs/ls1028ardb_tfa_defconfig | 61 ++++++++ include/configs/ls1028a_common.h | 295 ++++++++++++++++++++++++++++++++++++ include/configs/ls1028ardb.h | 98 ++++++++++++ 13 files changed, 1208 insertions(+) create mode 100644 arch/arm/dts/fsl-ls1028a-rdb.dts create mode 100644 board/freescale/ls1028a/Kconfig create mode 100644 board/freescale/ls1028a/MAINTAINERS create mode 100644 board/freescale/ls1028a/Makefile create mode 100644 board/freescale/ls1028a/README create mode 100644 board/freescale/ls1028a/ddr.c create mode 100644 board/freescale/ls1028a/ddr.h create mode 100644 board/freescale/ls1028a/ls1028a.c create mode 100644 configs/ls1028ardb_tfa_defconfig create mode 100644 include/configs/ls1028a_common.h create mode 100644 include/configs/ls1028ardb.h

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index f42ecce..aaaf36a 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1203,6 +1203,17 @@ config TARGET_LS1012AFRDM development platform that supports the QorIQ LS1012A Layerscape Architecture processor.

+config TARGET_LS1028ARDB

• bool "Support ls1028ardb"
• select ARCH_LS1028A
• select ARM64
• select ARMV8_MULTIENTRY
• help

•  Support for Freescale LS1028ARDB platform
  

•  The LS1028A Development System (RDB) is a high-performance
  

•  development platform that supports the QorIQ LS1028A
  

•  Layerscape Architecture processor.
  

config TARGET_LS1088ARDB bool "Support ls1088ardb" select ARCH_LS1088A @@ -1585,6 +1596,7 @@ source "board/freescale/ls2080a/Kconfig" source "board/freescale/ls2080aqds/Kconfig" source "board/freescale/ls2080ardb/Kconfig" source "board/freescale/ls1088a/Kconfig" +source "board/freescale/ls1028a/Kconfig" source "board/freescale/ls1021aqds/Kconfig" source "board/freescale/ls1043aqds/Kconfig" source "board/freescale/ls1021atwr/Kconfig" diff --git a/arch/arm/cpu/armv8/Kconfig b/arch/arm/cpu/armv8/Kconfig index f053603..a4fa63b 100644 --- a/arch/arm/cpu/armv8/Kconfig +++ b/arch/arm/cpu/armv8/Kconfig @@ -104,6 +104,7 @@ config PSCI_RESET !TARGET_LS1012ARDB && !TARGET_LS1012AFRDM && \ !TARGET_LS1012A2G5RDB && !TARGET_LS1012AQDS && \ !TARGET_LS1012AFRWY && \

•    !TARGET_LS1028ARDB && \
  

  !TARGET_LS1043ARDB && !TARGET_LS1043AQDS && \ !TARGET_LS1046ARDB && !TARGET_LS1046AQDS && \ !TARGET_LS2081ARDB && !TARGET_LX2160ARDB && \ diff -

-git a/arch/arm/dts/fsl-ls1028a-rdb.dts b/arch/arm/dts/fsl-ls1028a-rdb.dts new file mode 100644 index 0000000..b9adb61 --- /dev/null +++ b/arch/arm/dts/fsl-ls1028a-rdb.dts @@ -0,0 +1,20 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/*

• • NXP ls1028ARDB device tree source
• • Copyright 2018-2019 NXP

Strange, SoC dtsi is having 2019 copyright and board file having 2018-2019.

Please correct it.

• */

+/dts-v1/;

+#include "fsl-ls1028a.dtsi"

+/ {

• model = "NXP Layerscape 1028a RDB Board";
• compatible = "fsl,ls1028a-rdb", "fsl,ls1028a"; };

+&sata {

• status = "okay";

+};

You may have to update this dts based on adding "status" filed in soc dtsi file.

diff --git a/board/freescale/ls1028a/Kconfig b/board/freescale/ls1028a/Kconfig new file mode 100644 index 0000000..f4733c2 --- /dev/null +++ b/board/freescale/ls1028a/Kconfig @@ -0,0 +1,38 @@ +if TARGET_LS1028ARDB

+config SYS_BOARD

• default "ls1028a"

+config SYS_VENDOR

• default "freescale"

+config SYS_SOC

• default "fsl-layerscape"

+config SYS_CONFIG_NAME

• default "ls1028ardb"

+config EMMC_BOOT

• bool "Support for booting from EMMC"
• default n

+config SYS_TEXT_BASE

• default 0x96000000 if SD_BOOT || EMMC_BOOT
• default 0x82000000 if TFABOOT
• default 0x20100000

+if FSL_LS_PPA +config SYS_LS_PPA_FW_ADDR

• hex "PPA Firmware Addr"
• default 0x20400000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS1028A
• default 0x400000 if SYS_LS_PPA_FW_IN_MMC && ARCH_LS1028A if

+CHAIN_OF_TRUST config SYS_LS_PPA_ESBC_ADDR

• hex "PPA header Addr"
• default 0x20600000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS1028A

endif endif

+source "board/freescale/common/Kconfig"

+endif diff --git a/board/freescale/ls1028a/MAINTAINERS b/board/freescale/ls1028a/MAINTAINERS new file mode 100644 index 0000000..f4990a2 --- /dev/null +++ b/board/freescale/ls1028a/MAINTAINERS @@ -0,0 +1,9 @@ +LS1028ARDB BOARD +M: Sudhanshu Gupta sudhanshu.gupta@nxp.com +M: Rai Harninder harninder.rai@nxp.com +M: Rajesh Bhagat rajesh.bhagat@nxp.com

Is patch sender not a maintainer??

+S: Maintained +F: board/freescale/ls1028a/ +F: include/configs/ls1028a_common.h +F: include/configs/ls1028ardb.h +F: configs/ls1028ardb_tfa_defconfig diff --git a/board/freescale/ls1028a/Makefile b/board/freescale/ls1028a/Makefile new file mode 100644 index 0000000..2d1e92f --- /dev/null +++ b/board/freescale/ls1028a/Makefile @@ -0,0 +1,8 @@ +# +# Copyright 2018 NXP

Update copyright

+# +# SPDX-License-Identifier: GPL-2.0+ +#

+obj-y += ls1028a.o +obj-y += ddr.o diff --git a/board/freescale/ls1028a/README b/board/freescale/ls1028a/README new file mode 100644 index 0000000..a3ce859 --- /dev/null +++ b/board/freescale/ls1028a/README @@ -0,0 +1,85 @@ +Overview +-------- +The LS1028A Reference Design (RDB) is a high-performance computing, +evaluation, and development platform that supports ARM SoC LS1028A and +its derivatives.

+LS1028A SoC Overview +-------------------------------------- +Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc

+RDB Default Switch Settings (1: ON; 0: OFF) +------------------------------------------- +For SD Boot +SW2: 10001000 +SW3: 01110000 +SW5: 00100000

+For FlexSPI Boot +SW2: 11111000 +SW3: 01110000 +SW5: 00100000

flexSPI driver is not upstream. This info should be removed.

+LS1028ARDB board Overview +------------------------- +Processor

• Two Arm Cortex- A72 processor cores:
• • Based on 64-bit ARMv8 architecture
• • Up to 1.3 GHz operation
• • Single-threaded cores with 48 KB L1 instruction cache and 32 KB L1
• data cache
• • Arranged as a single cluster of two cores sharing a single 1 MB L2
• cache

+DDR memory

• • Five onboard 1G x8 discrete memory modules (Four data byte lanes
• ECC)
• • 32-bit data and 4-bit ECC
• • One chip select
• • Data transfer rates of up to 1.6 GT/s
• • Single-bit error correction and double-bit error detection ECC (4-bit
• check word across 32-bit data)

+High-speed serial ports(SerDes)

• • Lane 0: Supports one 1 GbE RJ45 SGMII, connected through the
• Qualcomm AR8033 PHY
• • Lane 1: Supports four 1.25 GbE RJ45 QSGMII, each connected
• through the NXP F104S8A PHY
• • Lane 2: Connects to one PCIe M.2 Key-E slot to support PCIe Gen3
• (8 Gbit/s) cards
• • Lane 3: Connects to one PCIe M.2 Key-E slot or one SATA M.2 Key-B
• slot through a register mux to support either PCIe Gen 3 (8 Gbit/s) or
• SATA Gen 3 cards (6 Gbit/s) at a time eSDHC
• • eSDHC1, eSDHC2

+SPI

• • Connects to two mikroBUS sockets to support mikro-click modules,
• such as Bluetooth 4.0, 2.4 GHz IEEE 802.15.4 radio transceiver, near
• field communications (NFC) controller Octal SPI (XSPI)
• • One 256 MB onboard XSPI serial NOR flash memory
• • One 512 MB onboard XSPI serial NAND flash memory
• • Supports a QSPI emulator for offboard QSPI emulation I2C
• • All system devices are accessed via I2C1, which is multiplexed on
• I2C multiplexer PCA9848 to isolate address conflicts and reduce
• capacitive load
• • I2C1 is used for EEPROMs, RTC, INA220 current-power sensor,
• thermal monitor, PCIe/SATA M.2 connectors and mikro-click modules
• 1 and 2

+CAN

• • The two CAN DB9 ports can support CAN FD fast phase at data rates of
• up to 5 Mbit/s

+Serial audio interface(SAI)

• • Audio codec SGTL5000 provides headphone and audio LINEOUT for
• stereo speakers
• • IEEE1588 interface to support audio on SAI4

+FlexSPI flash memory map valid for both QDS and RDB

• Image Flash Offset
• RCW+PBI 0x00000000
• Boot firmware (U-Boot) 0x00100000
• Boot firmware Environment 0x00300000
• PPA firmware 0x00400000
• DPAA2 MC 0x00A00000
• DPAA2 DPL 0x00D00000
• DPAA2 DPC 0x00E00000
• Kernel.itb 0x01000000

flexSPI memory map should not be there. There is no flexSPI driver

diff --git a/board/freescale/ls1028a/ddr.c b/board/freescale/ls1028a/ddr.c new file mode 100644 index 0000000..bb342dc --- /dev/null +++ b/board/freescale/ls1028a/ddr.c @@ -0,0 +1,284 @@ +// SPDX-License-Identifier: GPL-2.0+ +/*

• • Copyright 2019 NXP
• */

+#include <common.h> +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> +#include <asm/arch/soc.h> +#include <asm/arch/clock.h> +#include <asm/io.h> +#include "ddr.h"

+DECLARE_GLOBAL_DATA_PTR;

+void fsl_ddr_board_options(memctl_options_t *popts,

• 	   dimm_params_t *pdimm,
  

• 	   unsigned int ctrl_num)
  

+{

• const struct board_specific_parameters *pbsp, *pbsp_highest =

NULL;

• ulong ddr_freq;
• if (ctrl_num > 1) {

• printf("Not supported controller number %d\n", ctrl_num);
  

• return;
  

• }
• if (!pdimm->n_ranks)

• return;
  

• pbsp = udimms[0];
• /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr

• * freqency and n_banks specified in board_specific_parameters
  

table.

• */
  

• ddr_freq = get_ddr_freq(0) / 1000000;
• while (pbsp->datarate_mhz_high) {

• if (pbsp->n_ranks == pdimm->n_ranks) {
  

• 	if (ddr_freq <= pbsp->datarate_mhz_high) {
  

• 		popts->clk_adjust = pbsp->clk_adjust;
  

• 		popts->wrlvl_start = pbsp->wrlvl_start;
  

• 		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  

• 		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  

• 		popts->cpo_override = pbsp->cpo_override;
  

• 		popts->write_data_delay =
  

• 			pbsp->write_data_delay;
  

• 		goto found;
  

• 	}
  

• 	pbsp_highest = pbsp;
  

• }
  

• pbsp++;
  

• }
• if (pbsp_highest) {

• printf("Error: board specific timing not found for %lu
  

MT/s\n",

•        ddr_freq);
  

• printf("Trying to use the highest speed (%u) parameters\n",
  

•        pbsp_highest->datarate_mhz_high);
  

• popts->clk_adjust = pbsp_highest->clk_adjust;
  

• popts->wrlvl_start = pbsp_highest->wrlvl_start;
  

• popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  

• popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  

• } else {

• panic("DIMM is not supported by this board");
  

• }

+found:

• debug("Found timing match: n_ranks %d, data rate %d, rank_gb

%d\n",

•      pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
  

• /* force DDR bus width to 32 bits */
• popts->data_bus_width = 1;
• popts->otf_burst_chop_en = 0;
• popts->burst_length = DDR_BL8;
• popts->bstopre = 0; /* enable auto precharge */
• /*

• * Factors to consider for half-strength driver enable:
  

• *	- number of DIMMs installed
  

• */
  

• popts->half_strength_driver_enable = 1;
• /*

• * Write leveling override
  

• */
  

• popts->wrlvl_override = 1;
• popts->wrlvl_sample = 0xf;
• /*

• * Rtt and Rtt_WR override
  

• */
  

• popts->rtt_override = 0;
• /* Enable ZQ calibration */
• popts->zq_en = 1;

+#ifdef CONFIG_SYS_FSL_DDR4

• popts->ddr_cdr1 = DDR_CDR1_DHC_EN |

DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);

• popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |

• 	  DDR_CDR2_VREF_OVRD(70);	/* Vref = 70% */
  

• /* optimize cpo for erratum A-009942 */
• popts->cpo_sample = 0x46;

+#else

• popts->cswl_override = DDR_CSWL_CS0;
• /* DHC_EN =1, ODT = 75 Ohm */
• popts->ddr_cdr1 = DDR_CDR1_DHC_EN |

DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);

• popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); #endif

Does this board support DDR3. If not remove else part

}

+#ifdef CONFIG_TARGET_LS1028ARDB +#ifdef CONFIG_SYS_DDR_RAW_TIMING +/* MT40A1G8SA-075:E */ +dimm_params_t ddr_raw_timing = {

• .n_ranks = 1,
• .rank_density = 4294967296u,
• .capacity = 4294967296u,
• .primary_sdram_width = 32,
• .ec_sdram_width = 4,
• .registered_dimm = 0,
• .mirrored_dimm = 0,
• .n_row_addr = 16,
• .n_col_addr = 10,
• .bank_addr_bits = 0,
• .bank_group_bits = 2,
• .edc_config = 2,
• .burst_lengths_bitmask = 0x0c,
• .tckmin_x_ps = 750,
• .tckmax_ps = 1900,
• .caslat_x = 0x0001FFE00,
• .taa_ps = 13500,
• .trcd_ps = 13500,
• .trp_ps = 13500,
• .tras_ps = 32000,
• .trc_ps = 45500,
• .trfc1_ps = 350000,
• .trfc2_ps = 260000,
• .trfc4_ps = 160000,
• .tfaw_ps = 21000,
• .trrds_ps = 3000,
• .trrdl_ps = 4900,
• .tccdl_ps = 5000,
• .refresh_rate_ps = 7800000,
• .dq_mapping[0] = 0x16,
• .dq_mapping[1] = 0x36,
• .dq_mapping[2] = 0x16,
• .dq_mapping[3] = 0x36,
• .dq_mapping[4] = 0x16,
• .dq_mapping[5] = 0x36,
• .dq_mapping[6] = 0x16,
• .dq_mapping[7] = 0x36,
• .dq_mapping[8] = 0x16,
• .dq_mapping[9] = 0x0,
• .dq_mapping[10] = 0x0,
• .dq_mapping[11] = 0x0,
• .dq_mapping[12] = 0x0,
• .dq_mapping[13] = 0x0,
• .dq_mapping[14] = 0x0,
• .dq_mapping[15] = 0x0,
• .dq_mapping[16] = 0x0,
• .dq_mapping[17] = 0x0,
• .dq_mapping_ors = 0,

+};

+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,

• 	    unsigned int controller_number,
  

• 	    unsigned int dimm_number)
  

+{

• static const char dimm_model[] = "Fixed DDR on board";
• if ((controller_number == 0) && (dimm_number == 0)) {

• memcpy(pdimm, &ddr_raw_timing,
  

sizeof(dimm_params_t));

• memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
  

• memcpy(pdimm->mpart, dimm_model,
  

sizeof(dimm_model) - 1);

• }
• return 0;

+} +#else +static phys_size_t fixed_sdram(void) +{

• size_t ddr_size;

+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_SPL)

• fsl_ddr_cfg_regs_t ddr_cfg_regs = {

• .cs[0].bnds		= 0x000000ff,
  

• .cs[0].config		= 0x80040422,
  

• .cs[0].config_2		= 0,
  

• .cs[1].bnds		= 0,
  

• .cs[1].config		= 0,
  

• .cs[1].config_2		= 0,
  

• .timing_cfg_3		= 0x01111000,
  

• .timing_cfg_0		= 0xd0550018,
  

• .timing_cfg_1		= 0xFAFC0C42,
  

• .timing_cfg_2		= 0x0048c114,
  

• .ddr_sdram_cfg		= 0xe50c000c,
  

• .ddr_sdram_cfg_2	= 0x00401110,
  

• .ddr_sdram_mode		= 0x01010230,
  

• .ddr_sdram_mode_2	= 0x0,
  

• .ddr_sdram_md_cntl	= 0x0600001f,
  

• .ddr_sdram_interval	= 0x18600618,
  

• .ddr_data_init		= 0xdeadbeef,
  

• .ddr_sdram_clk_cntl	= 0x02000000,
  

• .ddr_init_addr		= 0,
  

• .ddr_init_ext_addr	= 0,
  

• .timing_cfg_4		= 0x00000002,
  

• .timing_cfg_5		= 0x07401400,
  

• .timing_cfg_6		= 0x0,
  

• .timing_cfg_7		= 0x23300000,
  

• .ddr_zq_cntl		= 0x8A090705,
  

• .ddr_wrlvl_cntl		= 0x86550607,
  

• .ddr_sr_cntr		= 0,
  

• .ddr_sdram_rcw_1	= 0,
  

• .ddr_sdram_rcw_2	= 0,
  

• .ddr_wrlvl_cntl_2	= 0x0708080A,
  

• .ddr_wrlvl_cntl_3	= 0x0A0B0C09,
  

• .ddr_sdram_mode_9	= 0x00000400,
  

• .ddr_sdram_mode_10	= 0x04000000,
  

• .timing_cfg_8		= 0x06115600,
  

• .dq_map_0		= 0x5b65b658,
  

• .dq_map_1		= 0xd96d8000,
  

• .dq_map_2		= 0,
  

• .dq_map_3		= 0x01600000,
  

• .ddr_cdr1		= 0x80040000,
  

• .ddr_cdr2		= 0x000000C1
  

• };
• fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0, 0); #endif
• ddr_size = 1ULL << 32;
• return ddr_size;

+}

Can we remove above mentioned magic numbers.

+#endif /* CONFIG_SYS_DDR_RAW_TIMING */ +#endif

+#ifdef CONFIG_TFABOOT +int fsl_initdram(void) +{

• gd->ram_size = tfa_get_dram_size();
• if (!gd->ram_size)

+#ifdef CONFIG_TARGET_LS1028ARDB

• gd->ram_size = 1ULL << 32;
  

Why this is hardcoded for RDB?

+#else

• gd->ram_size = fsl_ddr_sdram_size();
  

+#endif

• return 0;

+} +#else +int fsl_initdram(void) +{ +#ifdef CONFIG_TARGET_LS1028ARDB +#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)

• gd->ram_size = 1ULL << 32;

+#else +#ifdef CONFIG_SYS_DDR_RAW_TIMING

• puts("Initializing DDR....\n");
• gd->ram_size = fsl_ddr_sdram();

+#else

• puts("Initializing DDR....using fixed timing\n");
• gd->ram_size = fixed_sdram();

+#endif /* CONFIG_SYS_DDR_RAW_TIMING */ +#endif +#else +#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)

• gd->ram_size = fsl_ddr_sdram_size();

+#else

• puts("Initializing DDR....using SPD\n");
• gd->ram_size = fsl_ddr_sdram();

+#endif +#endif /* !CONFIG_TARGET_LS1028ARDB */

• return 0;

+} +#endif /* CONFIG_TFABOOT */

Lot of changes in one file to support QDS and RDB. Suggest to split files as ddr_rdb.c and ddr_qds.c for clarity.

diff --git a/board/freescale/ls1028a/ddr.h b/board/freescale/ls1028a/ddr.h new file mode 100644 index 0000000..aae54e7 --- /dev/null +++ b/board/freescale/ls1028a/ddr.h @@ -0,0 +1,46 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/*

• • Copyright 2019 NXP
• */

+#ifndef __DDR_H__ +#define __DDR_H__

+struct board_specific_parameters {

• u32 n_ranks;
• u32 datarate_mhz_high;
• u32 rank_gb;
• u32 clk_adjust;
• u32 wrlvl_start;
• u32 wrlvl_ctl_2;
• u32 wrlvl_ctl_3;
• u32 cpo_override;
• u32 write_data_delay;
• u32 force_2t;

+};

+/*

• • These tables contain all valid speeds we want to override with board
• • specific parameters. datarate_mhz_high values need to be in

+ascending order

• • for each n_ranks group.
• */

+static const struct board_specific_parameters udimm0[] = {

• /*

• * memory controller 0
  

• *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl | cpo  |wrdata|2T
  

• * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3  |      |delay |
  

• */
  

+#ifdef CONFIG_TARGET_LS1028ARDB

• {1, 1666, 0, 8, 5, 0x06070700, 0x00000008,},

+#else

• {2, 1666, 0, 8, 8, 0x090a0b00, 0x0000000c,},
• {1, 1666, 0, 8, 8, 0x090a0b00, 0x0000000c,},

+#endif

• {}

+};

+static const struct board_specific_parameters *udimms[] = {

• udimm0,

+};

+#endif diff --git a/board/freescale/ls1028a/ls1028a.c b/board/freescale/ls1028a/ls1028a.c new file mode 100644 index 0000000..63f8b7f --- /dev/null +++ b/board/freescale/ls1028a/ls1028a.c @@ -0,0 +1,251 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/*

• • Copyright 2019 NXP
• */

+#include <common.h> +#include <malloc.h> +#include <errno.h> +#include <fsl_ddr.h> +#include <asm/io.h> +#include <hwconfig.h> +#include <fdt_support.h> +#include <linux/libfdt.h> +#include <environment.h> +#include <asm/arch-fsl-layerscape/soc.h> #include <i2c.h> #include +<asm/arch/soc.h> #ifdef CONFIG_FSL_LS_PPA #include <asm/arch/ppa.h> +#endif #include <fsl_immap.h> #include <netdev.h>

+#include <fdtdec.h> +#include <miiphy.h> +#include "../common/qixis.h"

+DECLARE_GLOBAL_DATA_PTR;

+int board_init(void) +{ +#ifdef CONFIG_ENV_IS_NOWHERE

• gd->env_addr = (ulong)&default_environment[0]; #endif

+#ifdef CONFIG_FSL_LS_PPA

• ppa_init();

+#endif

+#ifndef CONFIG_SYS_EARLY_PCI_INIT

• /* run PCI init to kick off ENETC */
• pci_init();

Is this code valid from upstream point of view?

+#endif

+#if defined(CONFIG_TARGET_LS1028ARDB)

• u8 val = I2C_MUX_CH_DEFAULT;
• i2c_write(I2C_MUX_PCA_ADDR_PRI, 0x0b, 1, &val, 1); #endif
• return 0;

+}

+int board_eth_init(bd_t *bis) +{

• return pci_eth_init(bis);

+}

+int board_early_init_f(void) +{ +#ifdef CONFIG_SYS_I2C_EARLY_INIT

• i2c_early_init_f();

+#endif

• fsl_lsch3_early_init_f();
• return 0;

+}

+void detail_board_ddr_info(void) +{

• puts("\nDDR ");
• print_size(gd->bd->bi_dram[0].size + gd->bd->bi_dram[1].size, "");
• print_ddr_info(0);

+}

+#ifdef CONFIG_OF_BOARD_SETUP +int ft_board_setup(void *blob, bd_t *bd) {

• u64 base[CONFIG_NR_DRAM_BANKS];
• u64 size[CONFIG_NR_DRAM_BANKS];
• ft_cpu_setup(blob, bd);
• /* fixup DT for the two GPP DDR banks */
• base[0] = gd->bd->bi_dram[0].start;
• size[0] = gd->bd->bi_dram[0].size;
• base[1] = gd->bd->bi_dram[1].start;
• size[1] = gd->bd->bi_dram[1].size;

+#ifdef CONFIG_RESV_RAM

• /* reduce size if reserved memory is within this bank */
• if (gd->arch.resv_ram >= base[0] &&

•    gd->arch.resv_ram < base[0] + size[0])
  

• size[0] = gd->arch.resv_ram - base[0];
  

• else if (gd->arch.resv_ram >= base[1] &&

•  gd->arch.resv_ram < base[1] + size[1])
  

• size[1] = gd->arch.resv_ram - base[1]; #endif
  

• fdt_fixup_memory_banks(blob, base, size, 2);
• return 0;

+} +#endif

+#ifdef CONFIG_FSL_QIXIS +int checkboard(void) +{ +#ifdef CONFIG_TFABOOT

• enum boot_src src = get_boot_src();

+#endif

• u8 sw;
• int clock;
• char *board;
• char buf[64] = {0};
• static const char *freq[6] = {"100.00", "125.00", "156.25",

• 			"161.13", "322.26", "100.00 SS"};
  

• cpu_name(buf);
• /* find the board details */
• sw = QIXIS_READ(id);
• switch (sw) {
• case 0x46:

• board = "QDS";
  

• break;
  

• case 0x47:

• board = "RDB";
  

• break;
  

• case 0x49:

• board = "HSSI";
  

• break;
  

• default:

• board = "unknown";
  

• break;
  

• }
• sw = QIXIS_READ(arch);
• printf("Board: %s-%s, Version: %c, boot from ",

•       buf, board, (sw & 0xf) + 'A' - 1);
  

• sw = QIXIS_READ(brdcfg[0]);
• sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;

+#ifdef CONFIG_TFABOOT

• if (src == BOOT_SOURCE_SD_MMC)

• puts("SD\n");
  

• else if (src == BOOT_SOURCE_SD_MMC2)

• puts("eMMC \n");
  

• else {

+#endif +#ifdef CONFIG_SD_BOOT

• puts("SD \n");
  

+#elif defined(CONFIG_EMMC_BOOT)

• puts("eMMC \n");
  

+#else

• switch (sw) {
  

• case 0:
  

• case 4:
  

• 	printf("NOR\n");
  

• 	break;
  

• case 1:
  

• 	printf("NAND\n");
  

• 	break;
  

• default:
  

• 	printf("invalid setting of SW%u\n",
  

QIXIS_LBMAP_SWITCH);

• 	break;
  

• }
  

+#endif +#ifdef CONFIG_TFABOOT

• }

+#endif

• printf("FPGA: v%d (%s: %s_%s)\n", QIXIS_READ(scver),

•       !qixis_read_released()  ? "INTERIM" : "RELEASED",
  

• 	board, qixis_read_date(buf));
  

• puts("SERDES1 Reference : ");
• sw = QIXIS_READ(brdcfg[2]);

+#ifdef CONFIG_TARGET_LS1028ARDB

• clock = (sw >> 6) & 3;

+#else

• clock = (sw >> 4) & 0xf;

+#endif

• printf("Clock1 = %sMHz ", freq[clock]); #ifdef

+CONFIG_TARGET_LS1028ARDB

• clock = (sw >> 4) & 3;

+#else

• clock = sw & 0xf;

+#endif

• printf("Clock2 = %sMHz\n", freq[clock]);
• return 0;

+} +#endif

+#ifdef CONFIG_TARGET_LS1028ARDB +int checkboard1(void)

Who is using this function?

+{

• static const char *freq[2] = {"100.00", "Reserved"};
• char buf[64];
• u8 sw;
• int clock;
• printf("Board: LS1028A-RDB, ");

+#ifdef CONFIG_FSL_QIXIS

• sw = QIXIS_READ(arch);
• printf("Board Arch: V%d, ", sw >> 4);
• printf("Board version: %c, boot from ", (sw & 0xf) + 'A');
• memset((u8 *)buf, 0x00, ARRAY_SIZE(buf));
• sw = QIXIS_READ(brdcfg[0]);
• sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;

+#ifdef CONFIG_SD_BOOT

• puts("SD card\n");

+#else

• switch (sw) {
• case 0:
• case 4:

• printf("NOR\n");
  

• break;
  

• case 1:

• printf("NAND\n");
  

• break;
  

• case 2:
• case 3:

• printf("EMU\n");
  

• break;
  

• default:

• printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
  

• break;
  

• }

+#endif

• printf("FPGA: v%d.%d\n", QIXIS_READ(scver),

QIXIS_READ(tagdata));

• puts("SERDES1 Reference : ");
• sw = QIXIS_READ(brdcfg[2]);
• clock = (sw >> 6) & 3;
• printf("Clock1 = %sMHz ", freq[clock]);
• clock = (sw >> 4) & 3;
• printf("Clock2 = %sMHz\n", freq[clock]); #endif
• return 0;

+} +#endif diff --git a/configs/ls1028ardb_tfa_defconfig b/configs/ls1028ardb_tfa_defconfig new file mode 100644 index 0000000..7a6068d --- /dev/null +++ b/configs/ls1028ardb_tfa_defconfig @@ -0,0 +1,61 @@

Regenerate this file using make savedefconfing

+CONFIG_ARM=y +CONFIG_TARGET_LS1028ARDB=y +CONFIG_SYS_FSL_SDHC_CLK_DIV=1 +CONFIG_TFABOOT=y +CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y +CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y +CONFIG_AHCI=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_NR_DRAM_BANKS=2 +# CONFIG_SYS_MALLOC_F is not set +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_BOOTDELAY=10 +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256 video=1920x1080- 32@60 cma=256M" +CONFIG_CMD_GREPENV=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_SF=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_CACHE=y +CONFIG_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1028a-rdb" +CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_NETCONSOLE=y +CONFIG_DM=y +CONFIG_SCSI_AHCI=y +CONFIG_SATA_CEVA=y +CONFIG_FSL_CAAM=y +CONFIG_DM_MMC=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set CONFIG_PHYLIB=y +CONFIG_PHY_ATHEROS=y CONFIG_DM_ETH=y CONFIG_PHY_GIGE=y CONFIG_E1000=y +CONFIG_PCI=y CONFIG_DM_PCI=y CONFIG_DM_PCI_COMPAT=y +CONFIG_PCIE_LAYERSCAPE=y CONFIG_SCSI=y CONFIG_DM_SCSI=y +CONFIG_SYS_NS16550=y CONFIG_SPI=y CONFIG_DM_SPI=y CONFIG_FSL_DSPI=y +CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y CONFIG_EFI_LOADER_BOUNCE_BUFFER=y diff --git a/include/configs/ls1028a_common.h b/include/configs/ls1028a_common.h new file mode 100644 index 0000000..23823b4 --- /dev/null +++ b/include/configs/ls1028a_common.h @@ -0,0 +1,295 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/*

• • Copyright 2019 NXP
• */

+#ifndef __L1028A_COMMON_H +#define __L1028A_COMMON_H

+/* SPL build */ +#ifdef CONFIG_SPL_BUILD

Considering it supports TFA boot. Do we still require SPL build defines?

+#define SPL_NO_FMAN

Do we have FMAN ins LS1028

+#define SPL_NO_DSPI +#define SPL_NO_PCIE +#define SPL_NO_ENV +#define SPL_NO_MISC +#define SPL_NO_USB +#define SPL_NO_SATA +#define SPL_NO_QE

Do you have QE in LS1028A

+#define SPL_NO_EEPROM +#endif +#if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT)) #define +SPL_NO_MMC #endif #if (defined(CONFIG_SPL_BUILD) && +defined(CONFIG_SD_BOOT_QSPI)) #define SPL_NO_IFC #endif

+#define CONFIG_REMAKE_ELF +#define CONFIG_FSL_LAYERSCAPE +#define CONFIG_MP

+#include <asm/arch/stream_id_lsch3.h> +#include <asm/arch/config.h> +#include <asm/arch/soc.h>

+/* Link Definitions */ +#ifdef CONFIG_TFABOOT +#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE +#else +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0) +#endif

+#define CONFIG_SKIP_LOWLEVEL_INIT

+#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL +#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_SYS_DDR_BLOCK2_BASE 0x2080000000ULL +#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 1

+#define CONFIG_CMD_MEMTEST +#define CONFIG_SYS_MEMTEST_START 0x80000000 +#define CONFIG_SYS_MEMTEST_END 0x9fffffff

+/*

• • SMP Definitinos
• */

+#define CPU_RELEASE_ADDR secondary_boot_func

+/* Generic Timer Definitions */ +#define COUNTER_FREQUENCY 25000000 /* 25MHz */

+/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024)

+/* I2C */ +#define CONFIG_SYS_I2C

+/* Serial Port */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0) / 2)

+#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }

+/* Miscellaneous configurable options */ +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)

+/* Physical Memory Map */ +#define CONFIG_CHIP_SELECTS_PER_CTRL 4

+#define CONFIG_HWCONFIG +#define HWCONFIG_BUFFER_SIZE 128

+#ifndef SPL_NO_ENV +/* Allow to overwrite serial and ethaddr */ #define +CONFIG_ENV_OVERWRITE

+#define BOOT_TARGET_DEVICES(func) \

• func(MMC, mmc, 0) \
• func(USB, usb, 0)

+#include <config_distro_bootcmd.h>

+/* Initial environment variables */ +#define CONFIG_EXTRA_ENV_SETTINGS \

• "board=ls1028ardb\0" \
• "hwconfig=fsl_ddr:bank_intlv=auto\0" \
• "ramdisk_addr=0x800000\0" \
• "ramdisk_size=0x2000000\0" \
• "fdt_high=0xffffffffffffffff\0" \
• "initrd_high=0xffffffffffffffff\0" \
• "fdt_addr=0x00f00000\0" \
• "kernel_addr=0x01000000\0" \
• "scriptaddr=0x80000000\0" \
• "scripthdraddr=0x80080000\0" \
• "fdtheader_addr_r=0x80100000\0" \
• "kernelheader_addr_r=0x80200000\0" \
• "load_addr=0xa0000000\0" \
• "kernel_addr_r=0x81000000\0" \
• "fdt_addr_r=0x90000000\0" \
• "ramdisk_addr_r=0xa0000000\0" \
• "kernel_start=0x1000000\0" \
• "kernelheader_start=0x800000\0" \
• "kernel_load=0xa0000000\0" \
• "kernel_size=0x2800000\0" \
• "kernelheader_size=0x40000\0" \
• "kernel_addr_sd=0x8000\0" \
• "kernel_size_sd=0x14000\0" \
• "kernelhdr_addr_sd=0x4000\0" \
• "kernelhdr_size_sd=0x10\0" \
• "console=ttyS0,115200\0" \
• "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
• BOOTENV \
• "boot_scripts=ls1028ardb_boot.scr\0" \
• "boot_script_hdr=hdr_ls1028ardb_bs.out\0" \
• "scan_dev_for_boot_part=" \

• "part list ${devtype} ${devnum} devplist; "   \
  

• "env exists devplist || setenv devplist 1; "  \
  

• "for distro_bootpart in ${devplist}; do "     \
  

•   "if fstype ${devtype} "                  \
  

• 	"${devnum}:${distro_bootpart} "      \
  

• 	"bootfstype; then "                  \
  

• 	"run scan_dev_for_boot; "            \
  

•   "fi; "                                   \
  

• "done\0"                                   \
  

• "scan_dev_for_boot=" \

• "echo Scanning ${devtype} "		  \
  

• 		"${devnum}:${distro_bootpart}...; "  \
  

• "for prefix in ${boot_prefixes}; do "	  \
  

• 	"run scan_dev_for_scripts; "	  \
  

• "done;"					  \
  

• "\0"					  \
  

• "boot_a_script=" \

• "load ${devtype} ${devnum}:${distro_bootpart} "  \
  

• 	"${scriptaddr} ${prefix}${script}; "    \
  

• "env exists secureboot && load ${devtype} "     \
  

• 	"${devnum}:${distro_bootpart} "		\
  

• 	"${scripthdraddr} ${prefix}${boot_script_hdr} " \
  

• 	"&& esbc_validate ${scripthdraddr};"    \
  

• "source ${scriptaddr}\0"	  \
  

• "qspi_bootcmd=echo Trying load from flexspi..;" \

• "sf probe && sf read $load_addr "         \
  

• "$kernel_start $kernel_size; env exists secureboot "	\
  

• "&& sf read $kernelheader_addr_r $kernelheader_start "
  

  \

• "$kernelheader_size && esbc_validate
  

${kernelheader_addr_r}; " \

• "bootm $load_addr#$board\0"		\
  

• "qspi_hdploadcmd=echo Trying load HDP firmware from flexspi..;"

\

• "hdp load 0x20900000 0x2000\0"		\
  

• "sd_bootcmd=echo Trying load from SD ..;" \

• "mmcinfo; mmc read $load_addr "		\
  

• "$kernel_addr_sd $kernel_size_sd && "	\
  

• "env exists secureboot && mmc read $kernelheader_addr_r
  

" \

• "$kernelhdr_addr_sd $kernelhdr_size_sd "		\
  

• " && esbc_validate ${kernelheader_addr_r};"	\
  

• "bootm $load_addr#$board\0"		\
  

• "sd_hdploadcmd=echo Trying load HDP firmware from SD..;" \

• "mmcinfo;mmc read $load_addr 0x4800 0x200 "
  

  \

• "&& hdp load $load_addr 0x2000\0"	\
  

• "emmc_bootcmd=echo Trying load from EMMC ..;" \

• "mmcinfo; mmc dev 1; mmc read $load_addr "		\
  

• "$kernel_addr_sd $kernel_size_sd && "	\
  

• "env exists secureboot && mmc read $kernelheader_addr_r
  

" \

• "$kernelhdr_addr_sd $kernelhdr_size_sd "		\
  

• " && esbc_validate ${kernelheader_addr_r};"	\
  

• "bootm $load_addr#$board\0"			\
  

• "emmc_hdploadcmd=echo Trying load HDP firmware from EMMC..;"

\

• "mmc dev 1;mmcinfo;mmc read $load_addr 0x4800 0x200 "
  

  \

• "&& hdp load $load_addr 0x2000\0"
  

Remove flexspi or qspi related stuff.

+#undef CONFIG_BOOTCOMMAND +#ifdef CONFIG_TFABOOT +#define XSPI_NOR_BOOTCOMMAND "run qspi_hdploadcmd; run

Remove as there is no FSPI?

distro_bootcmd; run qspi_bootcmd; " \

• 		"env exists secureboot && esbc_halt;;"
  

+#define SD_BOOTCOMMAND "run sd_hdploadcmd; run distro_bootcmd;run sd_bootcmd; " \

• 		"env exists secureboot && esbc_halt;"
  

+#define SD2_BOOTCOMMAND "run emmc_hdploadcmd; run

When and where SD2_BOOTCOMMAND is being used?

distro_bootcmd;run emmc_bootcmd; " \

• 		"env exists secureboot && esbc_halt;"
  

+#else +#if defined(CONFIG_SD_BOOT) +#define CONFIG_BOOTCOMMAND "run sd_hdploadcmd; run distro_bootcmd;run sd_bootcmd; " \

• 	   "env exists secureboot && esbc_halt;"
  

+#elif defined(CONFIG_EMMC_BOOT) +#define CONFIG_BOOTCOMMAND "run emmc_hdploadcmd; run distro_bootcmd;run emmc_bootcmd; " \

• 	   "env exists secureboot && esbc_halt;"
  

+#else +#define CONFIG_BOOTCOMMAND "run qspi_hdploadcmd; run distro_bootcmd; run qspi_bootcmd; " \

• 	   "env exists secureboot && esbc_halt;"
  

+#endif +#endif /* CONFIG_TFABOOT */ +#endif

+/* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \

• 			sizeof(CONFIG_SYS_PROMPT) + 16)
  

+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */

+#ifndef SPL_NO_MISC +#ifndef CONFIG_CMDLINE_EDITING +#define CONFIG_CMDLINE_EDITING 1 +#endif +#endif

+#define CONFIG_SYS_MAXARGS 64 /* max command args */

+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */

+/* MMC */ +#ifndef SPL_NO_MMC +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 +#endif +#endif

+#ifdef CONFIG_SPL +#define CONFIG_SPL_BSS_START_ADDR 0x80100000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000 +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" +#define CONFIG_SPL_MAX_SIZE 0x16000 +#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0) +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"

Considering tfa boot is default boot target. Do we still required spl builds?

+#define CONFIG_SPL_TEXT_BASE 0x18010000

+#define CONFIG_SPL_I2C_SUPPORT

+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000 +#define CONFIG_SYS_SPL_MALLOC_START 0x80200000 +#define CONFIG_SYS_MONITOR_LEN (768 * 1024) +#endif

+#ifdef CONFIG_TFABOOT +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define OCRAM_NONSECURE_SIZE 0x00010000 +#define CONFIG_ENV_OFFSET 0x500000 /* 5MB */ +#define CONFIG_SYS_FSL_QSPI_BASE 0x20000000 +#define CONFIG_ENV_ADDR CONFIG_SYS_FSL_QSPI_BASE

• CONFIG_ENV_OFFSET

+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#define CONFIG_ENV_SECT_SIZE 0x40000 +#else +#if defined(CONFIG_SD_BOOT) || defined(CONFIG_EMMC_BOOT) +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_OFFSET 0x300000 /* 3MB */ +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#define OCRAM_NONSECURE_SIZE 0x00010000 +#else +#define CONFIG_ENV_OFFSET 0x300000 /* 3MB */ +#define CONFIG_SYS_FSL_QSPI_BASE 0x20000000 +#define CONFIG_ENV_ADDR CONFIG_SYS_FSL_QSPI_BASE

• CONFIG_ENV_OFFSET

+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#define CONFIG_ENV_SECT_SIZE 0x40000 +#endif +#endif

+#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE #else #define +CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE #endif

+/* MMC */ +#ifndef SPL_NO_MMC +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 +#endif +#endif

+/* I2C bus multiplexer */ +#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/ +#define I2C_MUX_CH_DEFAULT 0x8

+/* EEPROM */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5

+#endif /* __L1028A_COMMON_H */ diff --git a/include/configs/ls1028ardb.h b/include/configs/ls1028ardb.h new file mode 100644 index 0000000..b9d966a --- /dev/null +++ b/include/configs/ls1028ardb.h @@ -0,0 +1,98 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/*

• • Copyright 2019 NXP
• */

+#ifndef __LS1028A_RDB_H +#define __LS1028A_RDB_H

+#include "ls1028a_common.h"

+#define CONFIG_SYS_CLK_FREQ 100000000 +#define CONFIG_DDR_CLK_FREQ 100000000 +#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ / 4)

+#define CONFIG_SYS_RTC_BUS_NUM 0

+/* DDR */ +#define CONFIG_SYS_DDR_RAW_TIMING +#define CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#define CONFIG_DIMM_SLOTS_PER_CTLR 1

+/* FlexSPI */ +#ifdef CONFIG_NXP_FSPI +#define NXP_FSPI_FLASH_SIZE SZ_256M +#define NXP_FSPI_FLASH_NUM 1 +#endif

Why flexSPI? Do you have driver for this ?

+/* Store environment at top of flash */ +#define CONFIG_ENV_SIZE 0x2000

+#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE #else #define +CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE #endif

+#define CONFIG_QIXIS_I2C_ACCESS +#define CONFIG_SYS_I2C_EARLY_INIT

+/*

• • QIXIS Definitions
• */

+#define CONFIG_FSL_QIXIS

+#ifdef CONFIG_FSL_QIXIS +#define QIXIS_BASE 0x7fb00000 +#define QIXIS_BASE_PHYS QIXIS_BASE +#define CONFIG_SYS_I2C_FPGA_ADDR 0x66 +#define QIXIS_LBMAP_SWITCH 2 +#define QIXIS_LBMAP_MASK 0xe0 +#define QIXIS_LBMAP_SHIFT 0x5 +#define QIXIS_LBMAP_DFLTBANK 0x00 +#define QIXIS_LBMAP_SD 0x00 +#define QIXIS_LBMAP_EMMC 0x00 +#define QIXIS_LBMAP_QSPI 0x00 +#define QIXIS_RCW_SRC_SD 0xf8 +#define QIXIS_RCW_SRC_EMMC 0xf9 +#define QIXIS_RCW_SRC_QSPI 0xff +#define QIXIS_RST_CTL_RESET 0x31 +#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x10 +#define QIXIS_RCFG_CTL_RECONFIG_START 0x11 +#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 +#define QIXIS_RST_FORCE_MEM 0x01

+#define CONFIG_SYS_FPGA_CSPR_EXT (0x0) +#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \

• 			CSPR_PORT_SIZE_8 | \
  

• 			CSPR_MSEL_GPCM | \
  

• 			CSPR_V)
  

+#define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024) +#define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \

• 			CSOR_NOR_NOR_MODE_AVD_NOR
  

| \

• 			CSOR_NOR_TRHZ_80)
  

+#endif

IFC??

Is there IFC in LS1028

+/* SATA */ +#ifndef SPL_NO_SATA +#ifndef CONFIG_CMD_EXT2 +#define CONFIG_CMD_EXT2 +#endif +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \

• CONFIG_SYS_SCSI_MAX_LUN)

+#define SCSI_VEND_ID 0x1b4b +#define SCSI_DEV_ID 0x9170 +#define CONFIG_SCSI_DEV_LIST {SCSI_VEND_ID, SCSI_DEV_ID} #define +CONFIG_SCSI_AHCI_PLAT +#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1 +#endif

+#ifdef CONFIG_SECURE_BOOT +#include <asm/fsl_secure_boot.h> +#endif

Code has support of secure_boot but I am not finding defconfig for the same. Either add defconfig or remove code related to secure boot.

--pk