If we bridge an external PHY to Xilinx's PCS/PMA PHY and would like to get and set the real status of the PHY facing the external world. Then we should phy_connect() to the external PHY instead of the PCS/PMA one. Thus, we add a pcs-phy DT entry, which have been merged in Linux, and leave the configuration of it to the driver itself.
Unlike Linux, where the PCS/PMA PHY is managed by phylink, managing the PCS/PMA PHY is only internal to the driver in U-Boot. The PCS/PMA PHY pressents only when the phy-mode is configured as SGMII or 1000Base-X, so it is always 1 Gbps and full-duplex and we may skip passing link information out.
Signed-off-by: Andy Chiu andy.chiu@sifive.com Reviewed-by: Greentime Hu greentime.hu@sifive.com --- drivers/net/xilinx_axi_emac.c | 26 ++++++++++++++++++++++++-- 1 file changed, 24 insertions(+), 2 deletions(-)
diff --git a/drivers/net/xilinx_axi_emac.c b/drivers/net/xilinx_axi_emac.c index 04277b1269..447e1d4c9c 100644 --- a/drivers/net/xilinx_axi_emac.c +++ b/drivers/net/xilinx_axi_emac.c @@ -107,6 +107,7 @@ struct axidma_plat { struct eth_pdata eth_pdata; struct axidma_reg *dmatx; struct axidma_reg *dmarx; + int pcsaddr; int phyaddr; u8 eth_hasnobuf; int phy_of_handle; @@ -117,6 +118,7 @@ struct axidma_plat { struct axidma_priv { struct axidma_reg *dmatx; struct axidma_reg *dmarx; + int pcsaddr; int phyaddr; struct axi_regs *iobase; phy_interface_t interface; @@ -299,6 +301,13 @@ static int axiemac_phy_init(struct udevice *dev) if (IS_ENABLED(CONFIG_DM_ETH_PHY)) priv->phyaddr = eth_phy_get_addr(dev);
+ /* + * Set address of PCS/PMA PHY to the one pointed by phy-handle for + * backward compatibility. + */ + if (priv->phyaddr != -1 && priv->pcsaddr == 0) + priv->pcsaddr = priv->phyaddr; + if (priv->phyaddr == -1) { /* Detect the PHY address */ for (i = 31; i >= 0; i--) { @@ -342,12 +351,12 @@ static int setup_phy(struct udevice *dev) * after DMA and ethernet resets and hence * check and clear if set. */ - ret = phyread(priv, priv->phyaddr, MII_BMCR, &temp); + ret = phyread(priv, priv->pcsaddr, MII_BMCR, &temp); if (ret) return 0; if (temp & BMCR_ISOLATE) { temp &= ~BMCR_ISOLATE; - ret = phywrite(priv, priv->phyaddr, MII_BMCR, temp); + ret = phywrite(priv, priv->pcsaddr, MII_BMCR, temp); if (ret) return 0; } @@ -778,6 +787,7 @@ static int axi_emac_probe(struct udevice *dev)
if (priv->mactype == EMAC_1G) { priv->eth_hasnobuf = plat->eth_hasnobuf; + priv->pcsaddr = plat->pcsaddr; priv->phyaddr = plat->phyaddr; priv->phy_of_handle = plat->phy_of_handle; priv->interface = pdata->phy_interface; @@ -855,6 +865,8 @@ static int axi_emac_of_to_plat(struct udevice *dev)
if (plat->mactype == EMAC_1G) { plat->phyaddr = -1; + /* PHYAD 0 always redirects to the PCS/PMA PHY */ + plat->pcsaddr = 0;
offset = fdtdec_lookup_phandle(gd->fdt_blob, node, "phy-handle"); @@ -872,6 +884,16 @@ static int axi_emac_of_to_plat(struct udevice *dev)
plat->eth_hasnobuf = fdtdec_get_bool(gd->fdt_blob, node, "xlnx,eth-hasnobuf"); + + if (pdata->phy_interface == PHY_INTERFACE_MODE_SGMII || + pdata->phy_interface == PHY_INTERFACE_MODE_1000BASEX) { + offset = fdtdec_lookup_phandle(gd->fdt_blob, node, + "pcs-phy"); + if (offset > 0) { + plat->pcsaddr = fdtdec_get_int(gd->fdt_blob, + offset, "reg", -1); + } + } }
return 0;