Backend driver for MUSB OTG controllers found on TI AM35x.
It seems that on AM35X interrupt status registers can be updated _before_ core registers. As we don't use true interrupts in U-Boot and poll interrupt status registers instead this can result in interrupt handler being called with non-updated core registers. This confuses the code and result in hanged transfers. Add a small delay in am35x_interrupt as a workaround.
Signed-off-by: Ilya Yanok yanok@cogentembedded.com Signed-off-by: Ilya Yanok ilya.yanok@cogentembedded.com ---
arch/arm/include/asm/omap_musb.h | 3 + drivers/usb/musb-new/Makefile | 1 + drivers/usb/musb-new/am35x.c | 709 +++++++++++++++++++++++++++++++++++ drivers/usb/musb-new/linux-compat.h | 1 + include/usb.h | 2 +- 5 files changed, 715 insertions(+), 1 deletion(-) create mode 100644 drivers/usb/musb-new/am35x.c
diff --git a/arch/arm/include/asm/omap_musb.h b/arch/arm/include/asm/omap_musb.h index 0081a68..46c8578 100644 --- a/arch/arm/include/asm/omap_musb.h +++ b/arch/arm/include/asm/omap_musb.h @@ -18,8 +18,11 @@ #define __ASM_ARM_OMAP_MUSB_H
extern struct musb_platform_ops musb_dsps_ops; +extern const struct musb_platform_ops am35x_ops;
struct omap_musb_board_data { void (*set_phy_power)(u8 on); + void (*clear_irq)(void); + void (*reset)(void); }; #endif /* __ASM_ARM_OMAP_MUSB_H */ diff --git a/drivers/usb/musb-new/Makefile b/drivers/usb/musb-new/Makefile index a753423..23fc735 100644 --- a/drivers/usb/musb-new/Makefile +++ b/drivers/usb/musb-new/Makefile @@ -10,6 +10,7 @@ COBJS-$(CONFIG_MUSB_GADGET) += musb_gadget.o musb_gadget_ep0.o musb_core.o COBJS-$(CONFIG_MUSB_GADGET) += musb_uboot.o COBJS-$(CONFIG_MUSB_HOST) += musb_host.o musb_core.o musb_uboot.o COBJS-$(CONFIG_USB_MUSB_DSPS) += musb_dsps.o +COBJS-$(CONFIG_USB_MUSB_AM35X) += am35x.o
CFLAGS_NO_WARN := $(call cc-option,-Wno-unused-variable) \ $(call cc-option,-Wno-unused-but-set-variable) \ diff --git a/drivers/usb/musb-new/am35x.c b/drivers/usb/musb-new/am35x.c new file mode 100644 index 0000000..57c9bd3 --- /dev/null +++ b/drivers/usb/musb-new/am35x.c @@ -0,0 +1,709 @@ +/* + * Texas Instruments AM35x "glue layer" + * + * Copyright (c) 2010, by Texas Instruments + * + * Based on the DA8xx "glue layer" code. + * Copyright (c) 2008-2009, MontaVista Software, Inc. source@mvista.com + * + * This file is part of the Inventra Controller Driver for Linux. + * + * The Inventra Controller Driver for Linux is free software; you + * can redistribute it and/or modify it under the terms of the GNU + * General Public License version 2 as published by the Free Software + * Foundation. + * + * The Inventra Controller Driver for Linux is distributed in + * the hope that it will be useful, but WITHOUT ANY WARRANTY; + * without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public + * License for more details. + * + * You should have received a copy of the GNU General Public License + * along with The Inventra Controller Driver for Linux ; if not, + * write to the Free Software Foundation, Inc., 59 Temple Place, + * Suite 330, Boston, MA 02111-1307 USA + * + */ + +#define __UBOOT__ +#ifndef __UBOOT__ +#include <linux/init.h> +#include <linux/module.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/dma-mapping.h> + +#include <plat/usb.h> +#else +#include <common.h> +#include <asm/omap_musb.h> +#include "linux-compat.h" +#endif + +#include "musb_core.h" + +/* + * AM35x specific definitions + */ +/* USB 2.0 OTG module registers */ +#define USB_REVISION_REG 0x00 +#define USB_CTRL_REG 0x04 +#define USB_STAT_REG 0x08 +#define USB_EMULATION_REG 0x0c +/* 0x10 Reserved */ +#define USB_AUTOREQ_REG 0x14 +#define USB_SRP_FIX_TIME_REG 0x18 +#define USB_TEARDOWN_REG 0x1c +#define EP_INTR_SRC_REG 0x20 +#define EP_INTR_SRC_SET_REG 0x24 +#define EP_INTR_SRC_CLEAR_REG 0x28 +#define EP_INTR_MASK_REG 0x2c +#define EP_INTR_MASK_SET_REG 0x30 +#define EP_INTR_MASK_CLEAR_REG 0x34 +#define EP_INTR_SRC_MASKED_REG 0x38 +#define CORE_INTR_SRC_REG 0x40 +#define CORE_INTR_SRC_SET_REG 0x44 +#define CORE_INTR_SRC_CLEAR_REG 0x48 +#define CORE_INTR_MASK_REG 0x4c +#define CORE_INTR_MASK_SET_REG 0x50 +#define CORE_INTR_MASK_CLEAR_REG 0x54 +#define CORE_INTR_SRC_MASKED_REG 0x58 +/* 0x5c Reserved */ +#define USB_END_OF_INTR_REG 0x60 + +/* Control register bits */ +#define AM35X_SOFT_RESET_MASK 1 + +/* USB interrupt register bits */ +#define AM35X_INTR_USB_SHIFT 16 +#define AM35X_INTR_USB_MASK (0x1ff << AM35X_INTR_USB_SHIFT) +#define AM35X_INTR_DRVVBUS 0x100 +#define AM35X_INTR_RX_SHIFT 16 +#define AM35X_INTR_TX_SHIFT 0 +#define AM35X_TX_EP_MASK 0xffff /* EP0 + 15 Tx EPs */ +#define AM35X_RX_EP_MASK 0xfffe /* 15 Rx EPs */ +#define AM35X_TX_INTR_MASK (AM35X_TX_EP_MASK << AM35X_INTR_TX_SHIFT) +#define AM35X_RX_INTR_MASK (AM35X_RX_EP_MASK << AM35X_INTR_RX_SHIFT) + +#define USB_MENTOR_CORE_OFFSET 0x400 + +struct am35x_glue { + struct device *dev; + struct platform_device *musb; + struct clk *phy_clk; + struct clk *clk; +}; +#define glue_to_musb(g) platform_get_drvdata(g->musb) + +/* + * am35x_musb_enable - enable interrupts + */ +static void am35x_musb_enable(struct musb *musb) +{ + void __iomem *reg_base = musb->ctrl_base; + u32 epmask; + + /* Workaround: setup IRQs through both register sets. */ + epmask = ((musb->epmask & AM35X_TX_EP_MASK) << AM35X_INTR_TX_SHIFT) | + ((musb->epmask & AM35X_RX_EP_MASK) << AM35X_INTR_RX_SHIFT); + + musb_writel(reg_base, EP_INTR_MASK_SET_REG, epmask); + musb_writel(reg_base, CORE_INTR_MASK_SET_REG, AM35X_INTR_USB_MASK); + + /* Force the DRVVBUS IRQ so we can start polling for ID change. */ + if (is_otg_enabled(musb)) + musb_writel(reg_base, CORE_INTR_SRC_SET_REG, + AM35X_INTR_DRVVBUS << AM35X_INTR_USB_SHIFT); +} + +/* + * am35x_musb_disable - disable HDRC and flush interrupts + */ +static void am35x_musb_disable(struct musb *musb) +{ + void __iomem *reg_base = musb->ctrl_base; + + musb_writel(reg_base, CORE_INTR_MASK_CLEAR_REG, AM35X_INTR_USB_MASK); + musb_writel(reg_base, EP_INTR_MASK_CLEAR_REG, + AM35X_TX_INTR_MASK | AM35X_RX_INTR_MASK); + musb_writeb(musb->mregs, MUSB_DEVCTL, 0); + musb_writel(reg_base, USB_END_OF_INTR_REG, 0); +} + +#ifndef __UBOOT__ +#define portstate(stmt) stmt + +static void am35x_musb_set_vbus(struct musb *musb, int is_on) +{ + WARN_ON(is_on && is_peripheral_active(musb)); +} + +#define POLL_SECONDS 2 + +static struct timer_list otg_workaround; + +static void otg_timer(unsigned long _musb) +{ + struct musb *musb = (void *)_musb; + void __iomem *mregs = musb->mregs; + u8 devctl; + unsigned long flags; + + /* + * We poll because AM35x's won't expose several OTG-critical + * status change events (from the transceiver) otherwise. + */ + devctl = musb_readb(mregs, MUSB_DEVCTL); + dev_dbg(musb->controller, "Poll devctl %02x (%s)\n", devctl, + otg_state_string(musb->xceiv->state)); + + spin_lock_irqsave(&musb->lock, flags); + switch (musb->xceiv->state) { + case OTG_STATE_A_WAIT_BCON: + devctl &= ~MUSB_DEVCTL_SESSION; + musb_writeb(musb->mregs, MUSB_DEVCTL, devctl); + + devctl = musb_readb(musb->mregs, MUSB_DEVCTL); + if (devctl & MUSB_DEVCTL_BDEVICE) { + musb->xceiv->state = OTG_STATE_B_IDLE; + MUSB_DEV_MODE(musb); + } else { + musb->xceiv->state = OTG_STATE_A_IDLE; + MUSB_HST_MODE(musb); + } + break; + case OTG_STATE_A_WAIT_VFALL: + musb->xceiv->state = OTG_STATE_A_WAIT_VRISE; + musb_writel(musb->ctrl_base, CORE_INTR_SRC_SET_REG, + MUSB_INTR_VBUSERROR << AM35X_INTR_USB_SHIFT); + break; + case OTG_STATE_B_IDLE: + if (!is_peripheral_enabled(musb)) + break; + + devctl = musb_readb(mregs, MUSB_DEVCTL); + if (devctl & MUSB_DEVCTL_BDEVICE) + mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ); + else + musb->xceiv->state = OTG_STATE_A_IDLE; + break; + default: + break; + } + spin_unlock_irqrestore(&musb->lock, flags); +} + +static void am35x_musb_try_idle(struct musb *musb, unsigned long timeout) +{ + static unsigned long last_timer; + + if (!is_otg_enabled(musb)) + return; + + if (timeout == 0) + timeout = jiffies + msecs_to_jiffies(3); + + /* Never idle if active, or when VBUS timeout is not set as host */ + if (musb->is_active || (musb->a_wait_bcon == 0 && + musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) { + dev_dbg(musb->controller, "%s active, deleting timer\n", + otg_state_string(musb->xceiv->state)); + del_timer(&otg_workaround); + last_timer = jiffies; + return; + } + + if (time_after(last_timer, timeout) && timer_pending(&otg_workaround)) { + dev_dbg(musb->controller, "Longer idle timer already pending, ignoring...\n"); + return; + } + last_timer = timeout; + + dev_dbg(musb->controller, "%s inactive, starting idle timer for %u ms\n", + otg_state_string(musb->xceiv->state), + jiffies_to_msecs(timeout - jiffies)); + mod_timer(&otg_workaround, timeout); +} +#endif + +static irqreturn_t am35x_musb_interrupt(int irq, void *hci) +{ + struct musb *musb = hci; + void __iomem *reg_base = musb->ctrl_base; +#ifndef __UBOOT__ + struct device *dev = musb->controller; + struct musb_hdrc_platform_data *plat = dev->platform_data; + struct omap_musb_board_data *data = plat->board_data; + struct usb_otg *otg = musb->xceiv->otg; +#else + struct omap_musb_board_data *data = + (struct omap_musb_board_data *)musb->controller; +#endif + unsigned long flags; + irqreturn_t ret = IRQ_NONE; + u32 epintr, usbintr; + +#ifdef __UBOOT__ + /* + * It seems that on AM35X interrupt registers can be updated + * before core registers. This confuses the code. + * As a workaround add a small delay here. + */ + udelay(10); +#endif + spin_lock_irqsave(&musb->lock, flags); + + /* Get endpoint interrupts */ + epintr = musb_readl(reg_base, EP_INTR_SRC_MASKED_REG); + + if (epintr) { + musb_writel(reg_base, EP_INTR_SRC_CLEAR_REG, epintr); + + musb->int_rx = + (epintr & AM35X_RX_INTR_MASK) >> AM35X_INTR_RX_SHIFT; + musb->int_tx = + (epintr & AM35X_TX_INTR_MASK) >> AM35X_INTR_TX_SHIFT; + } + + /* Get usb core interrupts */ + usbintr = musb_readl(reg_base, CORE_INTR_SRC_MASKED_REG); + if (!usbintr && !epintr) + goto eoi; + + if (usbintr) { + musb_writel(reg_base, CORE_INTR_SRC_CLEAR_REG, usbintr); + + musb->int_usb = + (usbintr & AM35X_INTR_USB_MASK) >> AM35X_INTR_USB_SHIFT; + } +#ifndef __UBOOT__ + /* + * DRVVBUS IRQs are the only proxy we have (a very poor one!) for + * AM35x's missing ID change IRQ. We need an ID change IRQ to + * switch appropriately between halves of the OTG state machine. + * Managing DEVCTL.SESSION per Mentor docs requires that we know its + * value but DEVCTL.BDEVICE is invalid without DEVCTL.SESSION set. + * Also, DRVVBUS pulses for SRP (but not at 5V) ... + */ + if (usbintr & (AM35X_INTR_DRVVBUS << AM35X_INTR_USB_SHIFT)) { + int drvvbus = musb_readl(reg_base, USB_STAT_REG); + void __iomem *mregs = musb->mregs; + u8 devctl = musb_readb(mregs, MUSB_DEVCTL); + int err; + + err = is_host_enabled(musb) && (musb->int_usb & + MUSB_INTR_VBUSERROR); + if (err) { + /* + * The Mentor core doesn't debounce VBUS as needed + * to cope with device connect current spikes. This + * means it's not uncommon for bus-powered devices + * to get VBUS errors during enumeration. + * + * This is a workaround, but newer RTL from Mentor + * seems to allow a better one: "re"-starting sessions + * without waiting for VBUS to stop registering in + * devctl. + */ + musb->int_usb &= ~MUSB_INTR_VBUSERROR; + musb->xceiv->state = OTG_STATE_A_WAIT_VFALL; + mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ); + WARNING("VBUS error workaround (delay coming)\n"); + } else if (is_host_enabled(musb) && drvvbus) { + MUSB_HST_MODE(musb); + otg->default_a = 1; + musb->xceiv->state = OTG_STATE_A_WAIT_VRISE; + portstate(musb->port1_status |= USB_PORT_STAT_POWER); + del_timer(&otg_workaround); + } else { + musb->is_active = 0; + MUSB_DEV_MODE(musb); + otg->default_a = 0; + musb->xceiv->state = OTG_STATE_B_IDLE; + portstate(musb->port1_status &= ~USB_PORT_STAT_POWER); + } + + /* NOTE: this must complete power-on within 100 ms. */ + dev_dbg(musb->controller, "VBUS %s (%s)%s, devctl %02x\n", + drvvbus ? "on" : "off", + otg_state_string(musb->xceiv->state), + err ? " ERROR" : "", + devctl); + ret = IRQ_HANDLED; + } +#endif + + if (musb->int_tx || musb->int_rx || musb->int_usb) + ret |= musb_interrupt(musb); + +eoi: + /* EOI needs to be written for the IRQ to be re-asserted. */ + if (ret == IRQ_HANDLED || epintr || usbintr) { + /* clear level interrupt */ + if (data->clear_irq) + data->clear_irq(); + /* write EOI */ + musb_writel(reg_base, USB_END_OF_INTR_REG, 0); + } + +#ifndef __UBOOT__ + /* Poll for ID change */ + if (is_otg_enabled(musb) && musb->xceiv->state == OTG_STATE_B_IDLE) + mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ); +#endif + + spin_unlock_irqrestore(&musb->lock, flags); + + return ret; +} + +#ifndef __UBOOT__ +static int am35x_musb_set_mode(struct musb *musb, u8 musb_mode) +{ + struct device *dev = musb->controller; + struct musb_hdrc_platform_data *plat = dev->platform_data; + struct omap_musb_board_data *data = plat->board_data; + int retval = 0; + + if (data->set_mode) + data->set_mode(musb_mode); + else + retval = -EIO; + + return retval; +} +#endif + +static int am35x_musb_init(struct musb *musb) +{ +#ifndef __UBOOT__ + struct device *dev = musb->controller; + struct musb_hdrc_platform_data *plat = dev->platform_data; + struct omap_musb_board_data *data = plat->board_data; +#else + struct omap_musb_board_data *data = + (struct omap_musb_board_data *)musb->controller; +#endif + void __iomem *reg_base = musb->ctrl_base; + u32 rev; + + musb->mregs += USB_MENTOR_CORE_OFFSET; + + /* Returns zero if e.g. not clocked */ + rev = musb_readl(reg_base, USB_REVISION_REG); + if (!rev) + return -ENODEV; + +#ifndef __UBOOT__ + usb_nop_xceiv_register(); + musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2); + if (IS_ERR_OR_NULL(musb->xceiv)) + return -ENODEV; + + if (is_host_enabled(musb)) + setup_timer(&otg_workaround, otg_timer, (unsigned long) musb); +#endif + + /* Reset the musb */ + if (data->reset) + data->reset(); + + /* Reset the controller */ + musb_writel(reg_base, USB_CTRL_REG, AM35X_SOFT_RESET_MASK); + + /* Start the on-chip PHY and its PLL. */ + if (data->set_phy_power) + data->set_phy_power(1); + + msleep(5); + + musb->isr = am35x_musb_interrupt; + + /* clear level interrupt */ + if (data->clear_irq) + data->clear_irq(); + + return 0; +} + +static int am35x_musb_exit(struct musb *musb) +{ +#ifndef __UBOOT__ + struct device *dev = musb->controller; + struct musb_hdrc_platform_data *plat = dev->platform_data; + struct omap_musb_board_data *data = plat->board_data; +#else + struct omap_musb_board_data *data = + (struct omap_musb_board_data *)musb->controller; +#endif + +#ifndef __UBOOT__ + if (is_host_enabled(musb)) + del_timer_sync(&otg_workaround); +#endif + + /* Shutdown the on-chip PHY and its PLL. */ + if (data->set_phy_power) + data->set_phy_power(0); + +#ifndef __UBOOT__ + usb_put_phy(musb->xceiv); + usb_nop_xceiv_unregister(); +#endif + + return 0; +} + +/* AM35x supports only 32bit read operation */ +void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst) +{ + void __iomem *fifo = hw_ep->fifo; + u32 val; + int i; + + /* Read for 32bit-aligned destination address */ + if (likely((0x03 & (unsigned long) dst) == 0) && len >= 4) { + readsl(fifo, dst, len >> 2); + dst += len & ~0x03; + len &= 0x03; + } + /* + * Now read the remaining 1 to 3 byte or complete length if + * unaligned address. + */ + if (len > 4) { + for (i = 0; i < (len >> 2); i++) { + *(u32 *) dst = musb_readl(fifo, 0); + dst += 4; + } + len &= 0x03; + } + if (len > 0) { + val = musb_readl(fifo, 0); + memcpy(dst, &val, len); + } +} + +#ifndef __UBOOT__ +static const struct musb_platform_ops am35x_ops = { +#else +const struct musb_platform_ops am35x_ops = { +#endif + .init = am35x_musb_init, + .exit = am35x_musb_exit, + + .enable = am35x_musb_enable, + .disable = am35x_musb_disable, + +#ifndef __UBOOT__ + .set_mode = am35x_musb_set_mode, + .try_idle = am35x_musb_try_idle, + + .set_vbus = am35x_musb_set_vbus, +#endif +}; + +#ifndef __UBOOT__ +static u64 am35x_dmamask = DMA_BIT_MASK(32); + +static int __devinit am35x_probe(struct platform_device *pdev) +{ + struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data; + struct platform_device *musb; + struct am35x_glue *glue; + + struct clk *phy_clk; + struct clk *clk; + + int ret = -ENOMEM; + + glue = kzalloc(sizeof(*glue), GFP_KERNEL); + if (!glue) { + dev_err(&pdev->dev, "failed to allocate glue context\n"); + goto err0; + } + + musb = platform_device_alloc("musb-hdrc", -1); + if (!musb) { + dev_err(&pdev->dev, "failed to allocate musb device\n"); + goto err1; + } + + phy_clk = clk_get(&pdev->dev, "fck"); + if (IS_ERR(phy_clk)) { + dev_err(&pdev->dev, "failed to get PHY clock\n"); + ret = PTR_ERR(phy_clk); + goto err2; + } + + clk = clk_get(&pdev->dev, "ick"); + if (IS_ERR(clk)) { + dev_err(&pdev->dev, "failed to get clock\n"); + ret = PTR_ERR(clk); + goto err3; + } + + ret = clk_enable(phy_clk); + if (ret) { + dev_err(&pdev->dev, "failed to enable PHY clock\n"); + goto err4; + } + + ret = clk_enable(clk); + if (ret) { + dev_err(&pdev->dev, "failed to enable clock\n"); + goto err5; + } + + musb->dev.parent = &pdev->dev; + musb->dev.dma_mask = &am35x_dmamask; + musb->dev.coherent_dma_mask = am35x_dmamask; + + glue->dev = &pdev->dev; + glue->musb = musb; + glue->phy_clk = phy_clk; + glue->clk = clk; + + pdata->platform_ops = &am35x_ops; + + platform_set_drvdata(pdev, glue); + + ret = platform_device_add_resources(musb, pdev->resource, + pdev->num_resources); + if (ret) { + dev_err(&pdev->dev, "failed to add resources\n"); + goto err6; + } + + ret = platform_device_add_data(musb, pdata, sizeof(*pdata)); + if (ret) { + dev_err(&pdev->dev, "failed to add platform_data\n"); + goto err6; + } + + ret = platform_device_add(musb); + if (ret) { + dev_err(&pdev->dev, "failed to register musb device\n"); + goto err6; + } + + return 0; + +err6: + clk_disable(clk); + +err5: + clk_disable(phy_clk); + +err4: + clk_put(clk); + +err3: + clk_put(phy_clk); + +err2: + platform_device_put(musb); + +err1: + kfree(glue); + +err0: + return ret; +} + +static int __devexit am35x_remove(struct platform_device *pdev) +{ + struct am35x_glue *glue = platform_get_drvdata(pdev); + + platform_device_del(glue->musb); + platform_device_put(glue->musb); + clk_disable(glue->clk); + clk_disable(glue->phy_clk); + clk_put(glue->clk); + clk_put(glue->phy_clk); + kfree(glue); + + return 0; +} + +#ifdef CONFIG_PM +static int am35x_suspend(struct device *dev) +{ + struct am35x_glue *glue = dev_get_drvdata(dev); + struct musb_hdrc_platform_data *plat = dev->platform_data; + struct omap_musb_board_data *data = plat->board_data; + + /* Shutdown the on-chip PHY and its PLL. */ + if (data->set_phy_power) + data->set_phy_power(0); + + clk_disable(glue->phy_clk); + clk_disable(glue->clk); + + return 0; +} + +static int am35x_resume(struct device *dev) +{ + struct am35x_glue *glue = dev_get_drvdata(dev); + struct musb_hdrc_platform_data *plat = dev->platform_data; + struct omap_musb_board_data *data = plat->board_data; + int ret; + + /* Start the on-chip PHY and its PLL. */ + if (data->set_phy_power) + data->set_phy_power(1); + + ret = clk_enable(glue->phy_clk); + if (ret) { + dev_err(dev, "failed to enable PHY clock\n"); + return ret; + } + + ret = clk_enable(glue->clk); + if (ret) { + dev_err(dev, "failed to enable clock\n"); + return ret; + } + + return 0; +} + +static struct dev_pm_ops am35x_pm_ops = { + .suspend = am35x_suspend, + .resume = am35x_resume, +}; + +#define DEV_PM_OPS &am35x_pm_ops +#else +#define DEV_PM_OPS NULL +#endif + +static struct platform_driver am35x_driver = { + .probe = am35x_probe, + .remove = __devexit_p(am35x_remove), + .driver = { + .name = "musb-am35x", + .pm = DEV_PM_OPS, + }, +}; + +MODULE_DESCRIPTION("AM35x MUSB Glue Layer"); +MODULE_AUTHOR("Ajay Kumar Gupta ajay.gupta@ti.com"); +MODULE_LICENSE("GPL v2"); + +static int __init am35x_init(void) +{ + return platform_driver_register(&am35x_driver); +} +module_init(am35x_init); + +static void __exit am35x_exit(void) +{ + platform_driver_unregister(&am35x_driver); +} +module_exit(am35x_exit); +#endif diff --git a/drivers/usb/musb-new/linux-compat.h b/drivers/usb/musb-new/linux-compat.h index 8140fd9..343ddd2 100644 --- a/drivers/usb/musb-new/linux-compat.h +++ b/drivers/usb/musb-new/linux-compat.h @@ -106,4 +106,5 @@ typedef unsigned long dmaaddr_t; #define wmb() asm volatile ("" : : :"memory") #endif
+#define msleep(a) udelay(a * 1000) #endif /* __LINUX_COMPAT_H__ */ diff --git a/include/usb.h b/include/usb.h index aa389e6..bf510e4 100644 --- a/include/usb.h +++ b/include/usb.h @@ -148,7 +148,7 @@ struct usb_device { defined(CONFIG_USB_R8A66597_HCD) || defined(CONFIG_USB_DAVINCI) || \ defined(CONFIG_USB_OMAP3) || defined(CONFIG_USB_DA8XX) || \ defined(CONFIG_USB_BLACKFIN) || defined(CONFIG_USB_AM35X) || \ - defined(CONFIG_USB_MUSB_DSPS) + defined(CONFIG_USB_MUSB_DSPS) || defined(CONFIG_USB_MUSB_AM35X)
int usb_lowlevel_init(int index, void **controller); int usb_lowlevel_stop(int index);