Some platforms (like socfpga A10) need a big hep before SDRAM is available (e.g. because FAT is used). For such platforms, simple_malloc is often not a good option as it does not support freeing memory. These platforms often use the non-Kconfig defines CONFIG_SYS_SPL_MALLOC_START (and its SIZE).
This patch allows enabling CONFIG_SPL_SYS_MALLOC_F_LEN while leaving CONFIG_SPL_SYS_MALLOC_SIMPLE disabled. In this case, the full malloc heap is made available as early as the simple_malloc heap would be normally.
This way, platforms can drop the non-Kconfig options to set up the full heap and rely on the same automatically calculated heap allocation used for simple heap.
Signed-off-by: Simon Goldschmidt simon.k.r.goldschmidt@gmail.com ---
Changes in v2: - use if() instead of #if - adapt documentation to using CONFIG_SPL_SYS_MALLOC_F_LEN for full-featured heap as well - ensure SPL_CLEAR_BSS_F is set when using SYS_MALLOC_F_LEN for full featured heap (or else, the heap status stored in bss will be overwritten between board_init_f and board_init_r)
Kconfig | 24 ++++++++++++++++-------- README | 15 +++++++++++---- common/spl/spl.c | 10 ++++++++-- drivers/core/Kconfig | 33 ++++++++++++++++----------------- 4 files changed, 51 insertions(+), 31 deletions(-)
diff --git a/Kconfig b/Kconfig index 305b265ed7..e4165692d1 100644 --- a/Kconfig +++ b/Kconfig @@ -155,22 +155,30 @@ config SYS_MALLOC_LEN config SPL_SYS_MALLOC_F_LEN hex "Size of malloc() pool in SPL before relocation" depends on SYS_MALLOC_F + depends on SPL_SYS_MALLOC_SIMPLE || SPL_CLEAR_BSS_F default SYS_MALLOC_F_LEN help - Before relocation, memory is very limited on many platforms. Still, - we can provide a small malloc() pool if needed. Driver model in - particular needs this to operate, so that it can allocate the - initial serial device and any others that are needed. + Before relocation (before calling board_init_r, that is), memory is + very limited on many platforms. Still, we can provide a small + malloc() pool if needed. Driver model in particular needs this to + operate, so that it can allocate the initial serial device and any + others that are needed. + This option controls the size of this initial malloc() pool by + default.
config TPL_SYS_MALLOC_F_LEN hex "Size of malloc() pool in TPL before relocation" depends on SYS_MALLOC_F + depends on TPL_SYS_MALLOC_SIMPLE || SPL_CLEAR_BSS_F default SYS_MALLOC_F_LEN help - Before relocation, memory is very limited on many platforms. Still, - we can provide a small malloc() pool if needed. Driver model in - particular needs this to operate, so that it can allocate the - initial serial device and any others that are needed. + Before relocation (before calling board_init_r, that is), memory is + very limited on many platforms. Still, we can provide a small + malloc() pool if needed. Driver model in particular needs this to + operate, so that it can allocate the initial serial device and any + others that are needed. + This option controls the size of this initial malloc() pool by + default.
menuconfig EXPERT bool "Configure standard U-Boot features (expert users)" diff --git a/README b/README index 6525b81e3f..abe2e22a3c 100644 --- a/README +++ b/README @@ -2477,13 +2477,19 @@ FIT uImage format: CONFIG_SPL_STACK.
CONFIG_SYS_SPL_MALLOC_START - Starting address of the malloc pool used in SPL. + This is one way of providing the starting address of the malloc + pool used in SPL. If CONFIG_SPL_SYS_MALLOC_SIMPLE isn't set, + the full-featured heap will be used and it will allocate its + memory from the initial stack if CONFIG_SPL_SYS_MALLOC_F_LEN is + != 0. If you need it to use a dedicated area, use this option + to set an absolute address for the initial heap. When this option is set the full malloc is used in SPL and it is set up by spl_init() and before that, the simple malloc() - can be used if CONFIG_SYS_MALLOC_F is defined. + can still be used if CONFIG_SPL_SYS_MALLOC_F_LEN is defined.
CONFIG_SYS_SPL_MALLOC_SIZE - The size of the malloc pool used in SPL. + The size of the malloc pool used in SPL if + CONFIG_SYS_SPL_MALLOC_START is set.
CONFIG_SPL_OS_BOOT Enable booting directly to an OS from SPL. @@ -2758,7 +2764,8 @@ Configuration Settings: - CONFIG_SYS_MALLOC_SIMPLE Provides a simple and small malloc() and calloc() for those boards which do not use the full malloc in SPL (which is - enabled with CONFIG_SYS_SPL_MALLOC_START). + enabled by default with CONFIG_SYS_SPL_MALLOC_START or + CONFIG_SPL_SYS_MALLOC_F_LEN).
- CONFIG_SYS_NONCACHED_MEMORY: Size of non-cached memory area. This area of memory will be diff --git a/common/spl/spl.c b/common/spl/spl.c index 88d4b8a9bf..dec06c6e07 100644 --- a/common/spl/spl.c +++ b/common/spl/spl.c @@ -383,8 +383,14 @@ static int spl_common_init(bool setup_malloc) #ifdef CONFIG_MALLOC_F_ADDR gd->malloc_base = CONFIG_MALLOC_F_ADDR; #endif - gd->malloc_limit = CONFIG_VAL(SYS_MALLOC_F_LEN); - gd->malloc_ptr = 0; + if (CONFIG_IS_ENABLED(SYS_MALLOC_SIMPLE)) { + gd->malloc_limit = CONFIG_VAL(SYS_MALLOC_F_LEN); + gd->malloc_ptr = 0; + } else { + mem_malloc_init(gd->malloc_base, + CONFIG_VAL(SYS_MALLOC_F_LEN)); + gd->flags |= GD_FLG_FULL_MALLOC_INIT; + } } #endif ret = bootstage_init(true); diff --git a/drivers/core/Kconfig b/drivers/core/Kconfig index ddf2fb3fb8..297c19383f 100644 --- a/drivers/core/Kconfig +++ b/drivers/core/Kconfig @@ -12,28 +12,27 @@ config SPL_DM bool "Enable Driver Model for SPL" depends on DM && SPL help - Enable driver model in SPL. You will need to provide a - suitable malloc() implementation. If you are not using the - full malloc() enabled by CONFIG_SYS_SPL_MALLOC_START, - consider using CONFIG_SYS_MALLOC_SIMPLE. In that case you - must provide CONFIG_SPL_SYS_MALLOC_F_LEN to set the size. - In most cases driver model will only allocate a few uclasses - and devices in SPL, so 1KB should be enable. See - CONFIG_SPL_SYS_MALLOC_F_LEN for more details on how to enable it. + Enable driver model in SPL. You will need to provide a suitable + malloc() implementation. In most cases driver model will only + allocate a few uclasses and devices in SPL wihout freeing them, so + 1KB should be enough. + If full malloc() (default if CONFIG_SYS_SPL_MALLOC_START or + CONFIG_SPL_SYS_MALLOC_F_LEN are set) is too big for your board, + consider using CONFIG_SPL_SYS_MALLOC_SIMPLE (see help of that option + or CONFIG_SPL_SYS_MALLOC_F_LEN for more info).
config TPL_DM bool "Enable Driver Model for TPL" depends on DM && TPL help - Enable driver model in TPL. You will need to provide a - suitable malloc() implementation. If you are not using the - full malloc() enabled by CONFIG_SYS_SPL_MALLOC_START, - consider using CONFIG_SYS_MALLOC_SIMPLE. In that case you - must provide CONFIG_SPL_SYS_MALLOC_F_LEN to set the size. - In most cases driver model will only allocate a few uclasses - and devices in SPL, so 1KB should be enough. See - CONFIG_SPL_SYS_MALLOC_F_LEN for more details on how to enable it. - Disable this for very small implementations. + Enable driver model in TPL. You will need to provide a suitable + malloc() implementation. In most cases driver model will only + allocate a few uclasses and devices in TPL wihout freeing them, so + 1KB should be enough. + If full malloc() (default if CONFIG_SYS_SPL_MALLOC_START or + CONFIG_TPL_SYS_MALLOC_F_LEN are set) is too big for your board, + consider using CONFIG_TPL_SYS_MALLOC_SIMPLE (see help of that option + or CONFIG_TPL_SYS_MALLOC_F_LEN for more info).
config DM_WARN bool "Enable warnings in driver model"