Problem w/ SATA/IDE on Kirkwood 88F6281 board:
I've got U-Boot 2011.12 working well on a 8192 Kirkwood board, _except_ for a nagging SATA problem. Currently, it loads and executes U-Boot fine, it boots fine from a USB drive, but I'm unable to get the SATA port to function correctly. Any insight from Albert, Prafulla or anyone else who recognizes this problem, would be greatly appreciated.
It will detect an known-good-SATA-drive with known-good-ext2-partitions and list its specs, but there are some errors:
U-Boot 2011.12 (Apr 01 2012 - 15:55:54) Cloud Engines-Pogoplug v4
SoC: Kirkwood 88F6281_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> ide reset
Reset IDE: Bus 0: OK Bus 1: OK Device 0: Model: TOSHIBA MK1655GSX Firm: FG010D Ser#: X9AHTNGQT Type: Hard Disk Supports 48-bit addressing Capacity: 152627.8 MB = 149.0 GB (312581808 x 512) Error (no IRQ) dev 0 blk 16: status 0x7f No Powersaving mode 7F Error (no IRQ) dev 0 blk 0: status 0x7f Device 1: not available Pogov4> ext2ls ide 0:1 / ** Bad partition - ide 0:1 ** Pogov4> ------------------------------------
With #define DEBUG enabled in common/cmd_ide.c, I see the following: ------------------------------------ Pogov4> ide reset
Reset IDE: Bus 0: ide_outb (dev= 0, port= 0x118, val= 0xe0) : @ 0xf1082118 ide_inb (dev= 0, port= 0x11c) : @ 0xf108211c -> 0x50 OK Bus 1: ide_outb (dev= 1, port= 0x118, val= 0xf0) : @ 0xf1082118 ide_inb (dev= 1, port= 0x11c) : @ 0xf108211c -> 0x50 OK Device 0: ide_outb (dev= 0, port= 0x118, val= 0xe0) : @ 0xf1082118 ide_outb (dev= 0, port= 0x11c, val= 0xec) : @ 0xf108211c ide_inb (dev= 0, port= 0x11c) : @ 0xf108211c -> 0xd0 ide_inb (dev= 0, port= 0x11c) : @ 0xf108211c -> 0x58 in input data base for read is f1082100 Model: ?�?�?�?�?�?� Firm: ?�?�?�?� Ser#: ?�?�?��?�?�?� Type: Hard Disk Supports 48-bit addressing Capacity: 524263.9 MB = 511.9 GB (1073692671 x 512) ide_read dev 0 start 10, blocks 1 buffer at 7FBB230 ide_outb (dev= 0, port= 0x118, val= 0xe0) : @ 0xf1082118 ide_inb (dev= 0, port= 0x11c) : @ 0xf108211c -> 0x58 ide_outb (dev= 0, port= 0x11c, val= 0xe5) : @ 0xf108211c ide_inb (dev= 0, port= 0x11c) : @ 0xf108211c -> 0xd8 ... ide_inb (dev= 0, port= 0x11c) : @ 0xf108211c -> 0xd8 ide_inb (dev= 0, port= 0x11c) : @ 0xf108211c -> 0x7f No Powersaving mode 7F ide_inb (dev= 0, port= 0x11c) : @ 0xf108211c -> 0x7f ide_outb (dev= 0, port= 0x108, val= 0x01) : @ 0xf1082108 ide_outb (dev= 0, port= 0x10c, val= 0x10) : @ 0xf108210c ide_outb (dev= 0, port= 0x110, val= 0x00) : @ 0xf1082110 ide_outb (dev= 0, port= 0x114, val= 0x00) : @ 0xf1082114 ide_outb (dev= 0, port= 0x118, val= 0xe0) : @ 0xf1082118 ide_outb (dev= 0, port= 0x11c, val= 0x20) : @ 0xf108211c ide_inb (dev= 0, port= 0x11c) : @ 0xf108211c -> 0x7f Error (no IRQ) dev 0 blk 16: status 0x7f ide_read dev 0 start 0, blocks 1 buffer at 7E30C30 ide_outb (dev= 0, port= 0x118, val= 0xe0) : @ 0xf1082118 ide_inb (dev= 0, port= 0x11c) : @ 0xf108211c -> 0x7f ide_outb (dev= 0, port= 0x11c, val= 0xe5) : @ 0xf108211c ide_inb (dev= 0, port= 0x11c) : @ 0xf108211c -> 0x80 ... ide_inb (dev= 0, port= 0x11c) : @ 0xf108211c -> 0x80 ide_inb (dev= 0, port= 0x11c) : @ 0xf108211c -> 0x7f No Powersaving mode 7F ide_inb (dev= 0, port= 0x11c) : @ 0xf108211c -> 0x7f ide_outb (dev= 0, port= 0x108, val= 0x01) : @ 0xf1082108 ide_outb (dev= 0, port= 0x10c, val= 0x00) : @ 0xf108210c ide_outb (dev= 0, port= 0x110, val= 0x00) : @ 0xf1082110 ide_outb (dev= 0, port= 0x114, val= 0x00) : @ 0xf1082114 ide_outb (dev= 0, port= 0x118, val= 0xe0) : @ 0xf1082118 ide_outb (dev= 0, port= 0x11c, val= 0x20) : @ 0xf108211c ide_inb (dev= 0, port= 0x11c) : @ 0xf108211c -> 0x7f Error (no IRQ) dev 0 blk 0: status 0x7f Device 1: ide_outb (dev= 1, port= 0x118, val= 0xf0) : @ 0xf1082118 ide_outb (dev= 1, port= 0x11c, val= 0xec) : @ 0xf108211c ide_inb (dev= 1, port= 0x11c) : @ 0xf108211c -> 0x7f not available ------------------------------------
Ideas, anyone?