Re: [U-Boot] [PATCH v4] at91: Update MEESC board support

Daniel Gorsulowski wrote:

This patch implements several updates: -disable CONFIG_ENV_OVERWRITE -add new hardware style variants and set the arch numbers appropriate -pass the serial# and hardware revision to the kernel -removed unused macros from include/configs/meesc.h -fixed multiline comment style

Signed-off-by: Daniel Gorsulowski Daniel.Gorsulowski@esd.eu

v2: - don't write the ethernet address to the EMAC module anymore

v3: - removed function meesc_set_arch_number and moved code to checkboard() - reworked function get_board_serial() - removed unused macros from include/configs/meesc.h

v4: - fixed commit message (to many characters) - fixed indentation in switch-case statement - fixed multiline comment style

board/esd/meesc/meesc.c | 65 +++++++++++++++++++++++++++++++++++++++++----- include/configs/meesc.h | 25 ++++++------------ 2 files changed, 66 insertions(+), 24 deletions(-)

diff --git a/board/esd/meesc/meesc.c b/board/esd/meesc/meesc.c index 636d0ed..7cdc04a 100644 --- a/board/esd/meesc/meesc.c +++ b/board/esd/meesc/meesc.c @@ -126,8 +126,10 @@ static void meesc_ethercat_hw_init(void) AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(9)); at91_sys_write(AT91_SMC1_CYCLE(0), AT91_SMC_NWECYCLE_(10) | AT91_SMC_NRDCYCLE_(5));

• /* Configure behavior at external wait signal, byte-select mode, 16 bit
• data bus width, none data float wait states and TDF optimization */

• /*

• * Configure behavior at external wait signal, byte-select mode, 16 bit
  

• * data bus width, none data float wait states and TDF optimization
  

• */
  

  at91_sys_write(AT91_SMC1_MODE(0), AT91_SMC_READMODE | AT91_SMC_EXNWMODE_READY | AT91_SMC_BAT_SELECT | AT91_SMC_DBW_16 | AT91_SMC_TDF_(0) |

@@ -156,8 +158,32 @@ int board_eth_init(bd_t *bis) int checkboard(void) { char str[32];

• puts("Board: esd CAN-EtherCAT Gateway");

• u_char hw_type; /* hardware type */
• /* read the "Type" register of the ET1100 controller */
• hw_type = readb(CONFIG_ET1100_BASE);
• switch (hw_type) {
• case 0x11:
• case 0x3F:

• /* ET1100 present, arch number of MEESC-Board */
  

• gd->bd->bi_arch_number = MACH_TYPE_MEESC;
  

• puts("Board: CAN-EtherCAT Gateway");
  

• break;
  

• case 0xFF:

• /* no ET1100 present, arch number of EtherCAN/2-Board */
  

• gd->bd->bi_arch_number = MACH_TYPE_ETHERCAN2;
  

• puts("Board: EtherCAN/2 Gateway");
  

• /* switch on LED1D */
  

• at91_set_gpio_output(AT91_PIN_PB12, 1);
  

• break;
  

• default:

• /* assume, no ET1100 present, arch number of EtherCAN/2-Board */
  

• gd->bd->bi_arch_number = MACH_TYPE_ETHERCAN2;
  

• printf("FATAL! Read invalid hw_type: %02X\n", hw_type);
  

• puts("Board: EtherCAN/2 Gateway");
  

You may want to soften this "FATAL" to "ERROR" I would expect a "FATAL" to be followed by a call to hang()

• break;
  

• } if (getenv_r("serial#", str, sizeof(str)) > 0) { puts(", serial# "); puts(str);

@@ -167,6 +193,32 @@ int checkboard(void) return 0; }

+#ifdef CONFIG_SERIAL_TAG +void get_board_serial(struct tag_serialnr *serialnr) +{

• char *str;
• char *serial = getenv("serial#");
• if (serial) {

• str = strchr(serial, '_');
  

• if (str && (strlen(str) >= 4)) {
  

• 	serialnr->high = (*(str + 1) << 8) | *(str + 2);
  

• 	serialnr->low = simple_strtoul(str + 3, NULL, 16);
  

How is serial# set? It seems like this is available if the user explicitly does a `setenv serial` So at best this is a placeholder for future function. The logic that decodes the variable assumes a format that a user is not going, in general, to use.

Tom