The save_boot_params_ret() prototype (for those of us, that have a valid SP on entry and can implement save_boot_params() in C), was previously only defined for !defined(CONFIG_ARM64).
This moves the declaration to a common block to ensure the prototype is available to everyone that might need it.
Signed-off-by: Philipp Tomsich philipp.tomsich@theobroma-systems.com ---
Changes in v2: None
arch/arm/include/asm/system.h | 62 +++++++++++++++++++++---------------------- 1 file changed, 31 insertions(+), 31 deletions(-)
diff --git a/arch/arm/include/asm/system.h b/arch/arm/include/asm/system.h index 79bd19a..e2af296 100644 --- a/arch/arm/include/asm/system.h +++ b/arch/arm/include/asm/system.h @@ -332,37 +332,6 @@ void psci_arch_init(void);
#ifndef __ASSEMBLY__
-/** - * save_boot_params() - Save boot parameters before starting reset sequence - * - * If you provide this function it will be called immediately U-Boot starts, - * both for SPL and U-Boot proper. - * - * All registers are unchanged from U-Boot entry. No registers need be - * preserved. - * - * This is not a normal C function. There is no stack. Return by branching to - * save_boot_params_ret. - * - * void save_boot_params(u32 r0, u32 r1, u32 r2, u32 r3); - */ - -/** - * save_boot_params_ret() - Return from save_boot_params() - * - * If you provide save_boot_params(), then you should jump back to this - * function when done. Try to preserve all registers. - * - * If your implementation of save_boot_params() is in C then it is acceptable - * to simply call save_boot_params_ret() at the end of your function. Since - * there is no link register set up, you cannot just exit the function. U-Boot - * will return to the (initialised) value of lr, and likely crash/hang. - * - * If your implementation of save_boot_params() is in assembler then you - * should use 'b' or 'bx' to return to save_boot_params_ret. - */ -void save_boot_params_ret(void); - #ifdef CONFIG_ARMV7_LPAE void switch_to_hypervisor_ret(void); #endif @@ -556,6 +525,37 @@ void mmu_page_table_flush(unsigned long start, unsigned long stop);
#ifndef __ASSEMBLY__ /** + * save_boot_params() - Save boot parameters before starting reset sequence + * + * If you provide this function it will be called immediately U-Boot starts, + * both for SPL and U-Boot proper. + * + * All registers are unchanged from U-Boot entry. No registers need be + * preserved. + * + * This is not a normal C function. There is no stack. Return by branching to + * save_boot_params_ret. + * + * void save_boot_params(u32 r0, u32 r1, u32 r2, u32 r3); + */ + +/** + * save_boot_params_ret() - Return from save_boot_params() + * + * If you provide save_boot_params(), then you should jump back to this + * function when done. Try to preserve all registers. + * + * If your implementation of save_boot_params() is in C then it is acceptable + * to simply call save_boot_params_ret() at the end of your function. Since + * there is no link register set up, you cannot just exit the function. U-Boot + * will return to the (initialised) value of lr, and likely crash/hang. + * + * If your implementation of save_boot_params() is in assembler then you + * should use 'b' or 'bx' to return to save_boot_params_ret. + */ +void save_boot_params_ret(void); + +/** * Change the cache settings for a region. * * \param start start address of memory region to change