Hi Hans,
On Thu, Dec 10, 2015 at 4:29 AM, Hans de Goede hdegoede@redhat.com wrote:
Hi Olliver and Joe,
On 11/30/2015 05:50 PM, Oliver Schinagl wrote:
From: Olliver Schinagl o.schinagl@ultimaker.com
This patch allows Kconfig to enable and set parameters to make it possible to read the MAC address from an EEPROM. This patch only sets up some environment variables, it is up to the specific boards to actually use these defines.
Besides the various tuneables as to how to access the eeprom (bus, address, addressing mode/length, 2 configurable that are EEPROM generic (e.g. SPI or some other form of access) which are:
NET_ETHADDR_EEPROM_OFFSET, indicating where in the EEPROM the start of the MAC address is. The default is 8 allowing for 8 bytes before the MAC for other purposes (header MAGIC for example).
NET_ETHADDR_EEPROM_CRC8, indicating the MAC is appended with a CRC8-CCIT checksum that should be verified.
Currently only I2C eeproms have been tested and thus only those options are available, but shouldn't be a limit. NET_ETHADDR_EEPROM_SPI can be just as created.
Signed-off-by: Olliver Schinagl o.schinagl@ultimaker.com
Thanks, from a sunxi pov this and the other 2 patches look good.
Joe can we have your ack for this one please and/or can you merge this one through your tree? Either way I will take care of the other 2 patches in this set.
I'm fine either way. I'm thinking I'll be pulling anything assigned to me in patchwork next week.
From my pov this is fine as v2016.01 material, but if you would rather postpone this to v2016.04 that is fine too.
Seems safe enough. v2016.01 is fine with me.
Thanks & Regards,
Hans
doc/README.enetaddr | 36 +++++++++++++++++++++++++++++++++ net/Kconfig | 58 +++++++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 94 insertions(+)
diff --git a/doc/README.enetaddr b/doc/README.enetaddr index 50e4899..c53b455 100644 --- a/doc/README.enetaddr +++ b/doc/README.enetaddr @@ -47,6 +47,42 @@ Correct flow of setting up the MAC address (summarized): Previous behavior had the MAC address always being programmed into hardware in the device's init() function.
+--------
- EEPROM
+--------
+When there is an EEPROM available on a board, but the EEPROM is not large enough +to store the whole environment, it may be desired to store a MAC address in the +onboard EEPROM. Using CONFIG_NET_ETHADDR_EEPROM enables this feature. Depending +on the board, the EEPROM may be connected on various methods, but currently, +only the I2C bus is available via CONFIG_NET_ETHADDR_EEPROM_I2C. +CONFIG_NET_ETHADDR_EEPROM_I2C_BUS I2C bus on which the eeprom is present and +CONFIG_NET_ETHADDR_EEPROM_I2C_ADDR set the address of the EEPROM, which +defaults to the very common 0x50. Small size EEPROM's generally use single byte +addressing but larger EEPROM's may use double byte addressing, which can be +configured using CONFIG_NET_ETHADDR_EEPROM_ADDRLEN.
+Within the EEPROM, the MAC address can be stored on any arbitrary offset, +CONFIG_NET_ETHADDR_EEPROM_OFFSET sets this to 8 as a default however, allowing +the first 8 bytes to be used for some header magic for example.
+After the 6 bytes used for the MAC address, there is an 8 byte field to indicate +the ID of the network interface this MAC address is for. 0xff here means 'for +the first available interface' and 0x00 means the first network interface, 0x01 +the second, etc. It is up to the platform however to enforce this.
+Appending the 6 MAC bytes and the 7th interface byte is a CRC8 byte over the +previous 7 bytes. Whether to check this CRC8 or not is dependent on +CONFIG_NET_ETHADDR_EEPROM_CRC8.
+Layout example:
+00000000 21 4d 61 67 69 63 2e 21 01 23 45 67 89 ab ff c0 |!Magic.!.#Eg....|
+where the Header magic (!Magic.!) is spread over the first 8 bytes, and the MAC +address '01-23-45-67-89-ab' for the first interface (0xff) with the CRC8 +checksum 0xc0.
Usage
diff --git a/net/Kconfig b/net/Kconfig index a44a783..aced51e 100644 --- a/net/Kconfig +++ b/net/Kconfig @@ -7,6 +7,64 @@ menuconfig NET
if NET
+config NET_ETHADDR_EEPROM
bool "Get ethaddr from eeprom"helpSelecting this will try to get the Ethernet address from anonboard
EEPROM and set into the environment if and only if theenvironment
does currently not already hold a MAC address. For moreinformation
see doc/README.enetaddr.+config NET_ETHADDR_EEPROM_I2C
depends on NET_ETHADDR_EEPROMbool "EEPROM on I2C bus"helpThis switch enables checks for an EEPROM on the I2C bus.Naturally
this will only work if there is an actual EEPROM connected onthe
I2C bus and the bus and device are properly configured via theoptions below.+config NET_ETHADDR_EEPROM_I2C_BUS
depends on NET_ETHADDR_EEPROM_I2Cint "I2C bus"default 0helpSelect the bus on which the EEPROM is present, defaults to bus
+config NET_ETHADDR_EEPROM_I2C_ADDR
depends on NET_ETHADDR_EEPROM_I2Chex "eeprom address"default 0x50helpSelect the address of the eeprom, defaults to address 0x50.+config NET_ETHADDR_EEPROM_I2C_ADDRLEN
depends on NET_ETHADDR_EEPROM_I2Cint "eeprom address length"default 1helpNumber of bytes to be used for the I2C address length. Typically1,
2 for large memories, 0 for register type devices with only oneregister.+config NET_ETHADDR_EEPROM_OFFSET
depends on NET_ETHADDR_EEPROMint "EEPROM offset"default 8helpSelect the byte offset of the MAC address within the page,defaults to byte 8.+config NET_ETHADDR_EEPROM_CRC8
depends on NET_ETHADDR_EEPROMbool "Check CRC8 of MAC"default yhelpOptionally, it is possible to run a CRC-8-CCITT check on the MACaddress. To do so, the MAC address is stored with a CRC8 byteappend.
This option enables the CRC check of the MAC address against theCRC
byte.- config NET_RANDOM_ETHADDR bool "Random ethaddr if unset" select LIB_RAND
U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot