Hi Fabio,
On 08/06/2016 04:11, Fabio Estevam wrote:
Hi Stefano,
On Mon, Jun 6, 2016 at 6:49 AM, Stefano Babic sbabic@denx.de wrote:
diff --git a/board/phytec/pcm058/README b/board/phytec/pcm058/README new file mode 100644 index 0000000..90e2818 --- /dev/null +++ b/board/phytec/pcm058/README @@ -0,0 +1,9 @@ +Building U-Boot for phytec-mira +-------------------------------
+There are two versions of the board (NAND or eMMC).
+To build for NAND:
+$ make phytec_mira_defconfig
This patch does not add the phytec_mira_defconfig file, so please fix the readme accordingly.
Right - I changed the name back to be compliant with other phytec boards in U-Boot, but I should improve the README - I ill do in V2.
On Phytec's website, the board is named (to be acquired) as phyboard-mira. I will write in README that it is the same board, with a link to Website.
+int board_spi_cs_gpio(unsigned bus, unsigned cs) +{
if (bus != 0 || (cs != 0))return -1;return -EINVAL?
Right !
+int board_init(void) +{
/* address of boot parameters */gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;+#if 1
#ifdef CONFIG_SYS_I2C_MXC ?
Ok, thanks !
setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);+#endif
+const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
static?
Of course - I will fix it in the whole file.
.dram_sdclk_0 = 0x00000030,.dram_sdclk_1 = 0x00000030,.dram_cas = 0x00000030,.dram_ras = 0x00000030,.dram_reset = 0x00000030,.dram_sdcke0 = 0x00000030,.dram_sdcke1 = 0x00000030,.dram_sdba2 = 0x00000000,.dram_sdodt0 = 0x00000030,.dram_sdodt1 = 0x00000030,.dram_sdqs0 = 0x00000030,.dram_sdqs1 = 0x00000030,.dram_sdqs2 = 0x00000030,.dram_sdqs3 = 0x00000030,.dram_sdqs4 = 0x00000030,.dram_sdqs5 = 0x00000030,.dram_sdqs6 = 0x00000030,.dram_sdqs7 = 0x00000030,.dram_dqm0 = 0x00000030,.dram_dqm1 = 0x00000030,.dram_dqm2 = 0x00000030,.dram_dqm3 = 0x00000030,.dram_dqm4 = 0x00000030,.dram_dqm5 = 0x00000030,.dram_dqm6 = 0x00000030,.dram_dqm7 = 0x00000030,+};
+const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = {
static?
.grp_ddr_type = 0x000C0000,.grp_ddrmode_ctl = 0x00020000,.grp_ddrpke = 0x00000000,.grp_addds = IMX6Q_DRIVE_STRENGTH,.grp_ctlds = IMX6Q_DRIVE_STRENGTH,.grp_ddrmode = 0x00020000,.grp_b0ds = IMX6Q_DRIVE_STRENGTH,.grp_b1ds = IMX6Q_DRIVE_STRENGTH,.grp_b2ds = IMX6Q_DRIVE_STRENGTH,.grp_b3ds = IMX6Q_DRIVE_STRENGTH,.grp_b4ds = IMX6Q_DRIVE_STRENGTH,.grp_b5ds = IMX6Q_DRIVE_STRENGTH,.grp_b6ds = IMX6Q_DRIVE_STRENGTH,.grp_b7ds = IMX6Q_DRIVE_STRENGTH,+};
+const struct mx6_mmdc_calibration mx6_mmcd_calib = {
static?
--- /dev/null +++ b/include/configs/pcm058.h @@ -0,0 +1,140 @@ +/*
- Copyright (C) Stefano Babic sbabic@denx.de
- SPDX-License-Identifier: GPL-2.0+
- */
+#ifndef __PHYBOARD_MIRA_CONFIG_H +#define __PHYBOARD_MIRA_CONFIG_H
There is no "mira" in the file name.
Thanks - I fix in V2
Best regards, Stefano