On Thu, Jan 19, 2023 at 11:45 PM Marek Vasut marex@denx.de wrote:
With DM clock support in place, it is easy to add RMII support into the MAC driver. The RMII cannot operate at 1000 Mbps and at 100 and 10 Mbps the clock frequency is 50 MHz and 5 MHz instead of 25 MHz and 2.5 MHz.
The board DT requires the following adjustments to EQoS node: phy-mode = "rmii"; assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>, <&clk IMX8MP_SYS_PLL2_100M>, <&clk IMX8MP_SYS_PLL2_50M>; assigned-clock-rates = <0>, <100000000>, <50000000>;
Signed-off-by: Marek Vasut marex@denx.de
Cc: "Ariel D'Alessandro" ariel.dalessandro@collabora.com Cc: "NXP i.MX U-Boot Team" uboot-imx@nxp.com Cc: Andrey Zhizhikin andrey.zhizhikin@leica-geosystems.com Cc: Fabio Estevam festevam@gmail.com Cc: Joe Hershberger joe.hershberger@ni.com Cc: Lukasz Majewski lukma@denx.de Cc: Marcel Ziswiler marcel.ziswiler@toradex.com Cc: Marek Vasut marex@denx.de Cc: Michael Trimarchi michael@amarulasolutions.com Cc: Peng Fan peng.fan@nxp.com Cc: Ramon Fried rfried.dev@gmail.com Cc: Sean Anderson seanga2@gmail.com Cc: Stefano Babic sbabic@denx.de Cc: Tim Harvey tharvey@gateworks.com Cc: Tommaso Merciai tommaso.merciai@amarulasolutions.com Cc: u-boot@lists.denx.de
drivers/net/dwc_eth_qos_imx.c | 26 +++++++++++++++----------- 1 file changed, 15 insertions(+), 11 deletions(-)
diff --git a/drivers/net/dwc_eth_qos_imx.c b/drivers/net/dwc_eth_qos_imx.c index d0b7ef75c26..55080257623 100644 --- a/drivers/net/dwc_eth_qos_imx.c +++ b/drivers/net/dwc_eth_qos_imx.c @@ -178,21 +178,25 @@ static int eqos_set_tx_clk_speed_imx(struct udevice *dev)
debug("%s(dev=%p):\n", __func__, dev);
switch (eqos->phy->speed) {case SPEED_1000:rate = 125 * 1000 * 1000;break;case SPEED_100:rate = 25 * 1000 * 1000;break;case SPEED_10:rate = 2.5 * 1000 * 1000;break;default:
if (eqos->phy->interface == PHY_INTERFACE_MODE_RMII)rate = 5000; /* 5000 kHz = 5 MHz */elserate = 2500; /* 2500 kHz = 2.5 MHz */if (eqos->phy->speed == SPEED_1000 &&eqos->phy->interface == PHY_INTERFACE_MODE_RGMII) {rate *= 50; /* Use 50x base rate i.e. 125 MHz */} else if (eqos->phy->speed == SPEED_100) {rate *= 10; /* Use 10x base rate */} else if (eqos->phy->speed == SPEED_10) {rate *= 1; /* Use base rate */} else { pr_err("invalid speed %d", eqos->phy->speed); return -EINVAL; }rate *= 1000; /* clk_set_rate() operates in Hz */ret = clk_set_rate(&eqos->clk_tx, rate); if (ret < 0) { pr_err("imx (tx_clk, %lu) failed: %d", rate, ret);-- 2.39.0
Reviewed-by: Ramon Fried rfried.dev@gmail.com