On Thu, Feb 15, 2018 at 8:17 AM, Calvin Johnson calvin.johnson@nxp.com wrote:
This patch enables ethernet support for ls1012a2g5rdb.
Signed-off-by: Calvin Johnson calvin.johnson@nxp.com Signed-off-by: Bhaskar Upadhaya Bhaskar.Upadhaya@nxp.com
Changes in v2: -New patch added to series to enable ethernet support for ls1012a2g5rdb
board/freescale/ls1012ardb/Kconfig | 14 ++++++++++++++ board/freescale/ls1012ardb/eth.c | 25 +++++++++++++++++++++++++ 2 files changed, 39 insertions(+)
diff --git a/board/freescale/ls1012ardb/Kconfig b/board/freescale/ls1012ardb/Kconfig index 6e6197a..4bb672c 100644 --- a/board/freescale/ls1012ardb/Kconfig +++ b/board/freescale/ls1012ardb/Kconfig @@ -44,6 +44,20 @@ config SYS_SOC config SYS_CONFIG_NAME default "ls1012a2g5rdb"
+if FSL_PFE +config SYS_LS_PFE_FW_ADDR
hex "Flash address of PFE firmware"default 0x40a00000+config DDR_PFE_PHYS_BASEADDR
hex "PFE DDR physical base address"default 0x03800000+config DDR_PFE_BASEADDR
hex "PFE DDR base address"default 0x83800000+endif
source "board/freescale/common/Kconfig"
endif diff --git a/board/freescale/ls1012ardb/eth.c b/board/freescale/ls1012ardb/eth.c index bf67590..fc062cf 100644 --- a/board/freescale/ls1012ardb/eth.c +++ b/board/freescale/ls1012ardb/eth.c @@ -26,6 +26,7 @@
static inline void ls1012ardb_reset_phy(void) { +#ifdef CONFIG_TARGET_LS1012ARDB /* Through reset IO expander reset both RGMII and SGMII PHYs */ i2c_reg_write(I2C_MUX_IO2_ADDR, 6, __PHY_MASK); i2c_reg_write(I2C_MUX_IO2_ADDR, 2, __PHY_ETH2_MASK); @@ -34,6 +35,7 @@ static inline void ls1012ardb_reset_phy(void) mdelay(10); i2c_reg_write(I2C_MUX_IO2_ADDR, 2, 0xFF); mdelay(50); +#endif }
int pfe_eth_board_init(struct udevice *dev) @@ -42,6 +44,11 @@ int pfe_eth_board_init(struct udevice *dev) struct mii_dev *bus; struct pfe_mdio_info mac_mdio_info; struct pfe_eth_dev *priv = dev_get_priv(dev);
struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;int srds_s1 = in_be32(&gur->rcwsr[4]) &FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;srds_s1 >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT; if (!init_done) { ls1012ardb_reset_phy();@@ -59,6 +66,8 @@ int pfe_eth_board_init(struct udevice *dev) pfe_set_mdio(priv->gemac_port, miiphy_get_dev_by_name(DEFAULT_PFE_MDIO_NAME));
switch (srds_s1) {case 0x3508: if (!priv->gemac_port) {
This needs to be indented.
/* MAC1 */ pfe_set_phy_address_mode(priv->gemac_port, EMAC1_PHY_ADDR,@@ -68,6 +77,22 @@ int pfe_eth_board_init(struct udevice *dev) pfe_set_phy_address_mode(priv->gemac_port, EMAC2_PHY_ADDR, PHY_INTERFACE_MODE_RGMII_TXID); }
break;case 0x2208:if (!priv->gemac_port) {
This indentation needs to be fixed.
/* MAC1 */pfe_set_phy_address_mode(priv->gemac_port, EMAC1_PHY_ADDR,PHY_INTERFACE_MODE_SGMII_2500);} else {/* MAC2 */pfe_set_phy_address_mode(priv->gemac_port, EMAC2_PHY_ADDR,PHY_INTERFACE_MODE_SGMII_2500);}break;default:printf("unsupported SerDes PRCTL= %d\n", srds_s1);break;} return 0;}
-- 2.7.4
U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot