Extends the mii_dev structure to participate in a full-blown MDIO and PHY driver scheme. The mii_dev structure and miiphy calls are modified in such a way to allow the original mii command and miiphy infrastructure to work as before, but also to support a new set of APIs which allow (among other things) sharing of PHY driver code and 10G support
The mii command will continue to support normal PHY management functions (Clause 22 of 802.3), but will not be changed to support 10G (Clause 45).
The basic design is similar to PHY Lib from Linux, but simplified for U-Boot's network and driver infrastructure.
We now have MDIO drivers and PHY drivers
An MDIO driver provides: read write reset
A PHY driver provides: (optionally): probe config - initial setup, starting of auto-negotiation startup - waiting for AN, and reading link state shutdown - any cleanup needed
The ethernet drivers interact with the PHY Lib using these functions: phy_connect() phy_config() phy_startup() phy_shutdown()
Each PHY driver can be configured separately, or all at once using phylib_all_drivers.h (added in the patch which adds the drivers)
Signed-off-by: Andy Fleming afleming@freescale.com --- common/Makefile | 1 + common/miiphyutil.c | 173 ++++++++++-- drivers/net/phy/Makefile | 1 + drivers/net/phy/phy.c | 705 ++++++++++++++++++++++++++++++++++++++++++++++ include/miiphy.h | 31 ++ include/phy.h | 487 ++++++++++++++++++++++++++++++++ net/eth.c | 6 + 7 files changed, 1375 insertions(+), 29 deletions(-) create mode 100644 drivers/net/phy/phy.c create mode 100644 include/phy.h
diff --git a/common/Makefile b/common/Makefile index 048df0c..00847ef 100644 --- a/common/Makefile +++ b/common/Makefile @@ -114,6 +114,7 @@ COBJS-$(CONFIG_CMD_MFSL) += cmd_mfsl.o COBJS-$(CONFIG_CMD_MG_DISK) += cmd_mgdisk.o COBJS-$(CONFIG_MII) += miiphyutil.o COBJS-$(CONFIG_CMD_MII) += miiphyutil.o +COBJS-$(CONFIG_PHYLIB) += miiphyutil.o COBJS-$(CONFIG_CMD_MII) += cmd_mii.o COBJS-$(CONFIG_CMD_MISC) += cmd_misc.o COBJS-$(CONFIG_CMD_MMC) += cmd_mmc.o diff --git a/common/miiphyutil.c b/common/miiphyutil.c index e282096..e79c639 100644 --- a/common/miiphyutil.c +++ b/common/miiphyutil.c @@ -28,6 +28,7 @@
#include <common.h> #include <miiphy.h> +#include <phy.h>
#include <asm/types.h> #include <linux/list.h> @@ -44,22 +45,13 @@ #define debug(fmt,args...) #endif /* MII_DEBUG */
-struct mii_dev { - struct list_head link; - const char *name; - int (*read) (const char *devname, unsigned char addr, - unsigned char reg, unsigned short *value); - int (*write) (const char *devname, unsigned char addr, - unsigned char reg, unsigned short value); -}; - static struct list_head mii_devs; static struct mii_dev *current_mii;
/* * Lookup the mii_dev struct by the registered device name. */ -static struct mii_dev *miiphy_get_dev_by_name(const char *devname, int quiet) +struct mii_dev *miiphy_get_dev_by_name(const char *devname) { struct list_head *entry; struct mii_dev *dev; @@ -75,8 +67,6 @@ static struct mii_dev *miiphy_get_dev_by_name(const char *devname, int quiet) return dev; }
- if (!quiet) - printf("No such device: %s\n", devname); return NULL; }
@@ -90,6 +80,25 @@ void miiphy_init(void) current_mii = NULL; }
+static int legacy_miiphy_read(struct mii_dev *bus, int addr, int devad, int reg) +{ + unsigned short val; + int ret; + struct legacy_mii_dev *ldev = bus->priv; + + ret = ldev->read(bus->name, addr, reg, &val); + + return ret ? -1 : (int)val; +} + +static int legacy_miiphy_write(struct mii_dev *bus, int addr, int devad, + int reg, u16 val) +{ + struct legacy_mii_dev *ldev = bus->priv; + + return ldev->write(bus->name, addr, reg, val); +} + /***************************************************************************** * * Register read and write MII access routines for the device <name>. @@ -101,11 +110,12 @@ void miiphy_register(const char *name, unsigned char reg, unsigned short value)) { struct mii_dev *new_dev; + struct legacy_mii_dev *ldev; unsigned int name_len; char *new_name;
/* check if we have unique name */ - new_dev = miiphy_get_dev_by_name(name, 1); + new_dev = miiphy_get_dev_by_name(name); if (new_dev) { printf("miiphy_register: non unique device name '%s'\n", name); return; @@ -113,10 +123,10 @@ void miiphy_register(const char *name,
/* allocate memory */ name_len = strlen (name); - new_dev = - (struct mii_dev *)malloc (sizeof (struct mii_dev) + name_len + 1); + new_dev = malloc (sizeof (struct mii_dev) + name_len + 1); + ldev = malloc (sizeof (*ldev));
- if (new_dev == NULL) { + if (new_dev == NULL || ldev == NULL) { printf ("miiphy_register: cannot allocate memory for '%s'\n", name); return; @@ -125,14 +135,17 @@ void miiphy_register(const char *name,
/* initalize mii_dev struct fields */ INIT_LIST_HEAD (&new_dev->link); - new_dev->read = read; - new_dev->write = write; + new_dev->read = legacy_miiphy_read; + new_dev->write = legacy_miiphy_write; new_dev->name = new_name = (char *)(new_dev + 1); strncpy (new_name, name, name_len); new_name[name_len] = '\0'; + ldev->read = read; + ldev->write = write; + new_dev->priv = ldev;
debug ("miiphy_register: added '%s', read=0x%08lx, write=0x%08lx\n", - new_dev->name, new_dev->read, new_dev->write); + new_dev->name, ldev->read, ldev->write);
/* add it to the list */ list_add_tail (&new_dev->link, &mii_devs); @@ -141,19 +154,119 @@ void miiphy_register(const char *name, current_mii = new_dev; }
+struct mii_dev *mdio_alloc(void) +{ + struct mii_dev *bus; + + bus = malloc(sizeof(*bus)); + if (!bus) + return bus; + + memset(bus, 0, sizeof (*bus)); + + bus->name = malloc(MDIO_NAME_LEN); + if (!bus->name) { + printf("Could not allocate name for mii_dev\n"); + free(bus); + return NULL; + } + + memset(bus->name, 0, MDIO_NAME_LEN); + + /* initalize mii_dev struct fields */ + INIT_LIST_HEAD (&bus->link); + + return bus; +} + +int mdio_register(struct mii_dev *bus) +{ + if (!bus || !bus->name || !bus->read || !bus->write) + return -1; + + /* check if we have unique name */ + if (miiphy_get_dev_by_name(bus->name)) { + printf("mdio_register: non unique device name '%s'\n", + bus->name); + return -1; + } + + /* add it to the list */ + list_add_tail (&bus->link, &mii_devs); + + if (!current_mii) + current_mii = bus; + + return 0; +} + +void mdio_list_devices(void) +{ + struct list_head *entry; + + list_for_each(entry, &mii_devs) { + int i; + struct mii_dev *bus = list_entry(entry, struct mii_dev, link); + + printf("%s:\n", bus->name); + + for (i = 0; i < PHY_MAX_ADDR; i++) { + struct phy_device *phydev = bus->phymap[i]; + + if (phydev) { + printf("%d - %s", i, phydev->drv->name); + + if (phydev->dev) + printf(" <--> %s\n", phydev->dev->name); + else + printf("\n"); + } + } + } +} + int miiphy_set_current_dev(const char *devname) { struct mii_dev *dev;
- dev = miiphy_get_dev_by_name(devname, 0); + dev = miiphy_get_dev_by_name(devname); if (dev) { current_mii = dev; return 0; }
+ printf("No such device: %s\n", devname); + return 1; }
+struct mii_dev *mdio_get_current_dev(void) +{ + return current_mii; +} + +struct phy_device *mdio_phydev_for_ethname(const char *ethname) +{ + struct list_head *entry; + struct mii_dev *bus; + + list_for_each(entry, &mii_devs) { + int i; + bus = list_entry(entry, struct mii_dev, link); + + for (i = 0; i < PHY_MAX_ADDR; i++) { + if ((!bus->phymap[i]) || (!bus->phymap[i]->dev)) + continue; + + if (strcmp(bus->phymap[i]->dev->name, ethname) == 0) + return bus->phymap[i]; + } + } + + printf("%s is not a known ethernet\n", ethname); + return NULL; +} + const char *miiphy_get_current_dev(void) { if (current_mii) @@ -187,13 +300,15 @@ static struct mii_dev *miiphy_get_active_dev(const char *devname) int miiphy_read(const char *devname, unsigned char addr, unsigned char reg, unsigned short *value) { - struct mii_dev *dev; + struct mii_dev *bus;
- dev = miiphy_get_active_dev(devname); - if (dev) - return dev->read(devname, addr, reg, value); + bus = miiphy_get_active_dev(devname); + if (bus) + *value = bus->read(bus, addr, MDIO_DEVAD_NONE, reg); + else + return 1;
- return 1; + return (*value < 0) ? 1 : 0; }
/***************************************************************************** @@ -207,11 +322,11 @@ int miiphy_read(const char *devname, unsigned char addr, unsigned char reg, int miiphy_write(const char *devname, unsigned char addr, unsigned char reg, unsigned short value) { - struct mii_dev *dev; + struct mii_dev *bus;
- dev = miiphy_get_active_dev(devname); - if (dev) - return dev->write(devname, addr, reg, value); + bus = miiphy_get_active_dev(devname); + if (bus) + return bus->write(bus, addr, MDIO_DEVAD_NONE, reg, value);
return 1; } diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile index bba8901..7cb1094 100644 --- a/drivers/net/phy/Makefile +++ b/drivers/net/phy/Makefile @@ -27,6 +27,7 @@ LIB := $(obj)libphy.o
COBJS-$(CONFIG_BITBANGMII) += miiphybb.o COBJS-$(CONFIG_MV88E61XX_SWITCH) += mv88e61xx.o +COBJS-$(CONFIG_PHYLIB) += phy.o
COBJS := $(COBJS-y) SRCS := $(COBJS:.o=.c) diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c new file mode 100644 index 0000000..ca35404 --- /dev/null +++ b/drivers/net/phy/phy.c @@ -0,0 +1,705 @@ +/* + * Generic PHY Management code + * + * This software may be used and distributed according to the + * terms of the GNU Public License, Version 2, incorporated + * herein by reference. + * + * Copyright 2011 Freescale Semiconductor, Inc. + * author Andy Fleming + * + * Based loosely off of Linux's PHY Lib + */ + +#include <config.h> +#include <common.h> +#include <malloc.h> +#include <net.h> +#include <command.h> +#include <miiphy.h> +#include <phy.h> +#include <errno.h> + +int phy_read(struct phy_device *phydev, int devad, int regnum) +{ + struct mii_dev *bus = phydev->bus; + + return bus->read(bus, phydev->addr, devad, regnum); +} + +int phy_write(struct phy_device *phydev, int devad, int regnum, u16 val) +{ + struct mii_dev *bus = phydev->bus; + + return bus->write(bus, phydev->addr, devad, regnum, val); +} + + +int gen10g_shutdown(struct phy_device *phydev) +{ + return 0; +} + +int gen10g_startup(struct phy_device *phydev) +{ + int devad, reg; + u32 mmd_mask = phydev->mmds; + + phydev->link = 1; + + /* For now just lie and say it's 10G all the time */ + phydev->speed = SPEED_10000; + phydev->duplex = DUPLEX_FULL; + + for (devad = 0; mmd_mask; devad++, mmd_mask = mmd_mask >> 1) { + if (!mmd_mask & 1) + continue; + + /* Read twice because link state is latched and a + * read moves the current state into the register */ + phy_read(phydev, devad, MDIO_STAT1); + reg = phy_read(phydev, devad, MDIO_STAT1); + if (reg < 0 || !(reg & MDIO_STAT1_LSTATUS)) + phydev->link = 0; + } + + return 0; +} + +int gen10g_config(struct phy_device *phydev) +{ + int mmd, stat2, devs1, devs2; + + phydev->supported = phydev->advertising = SUPPORTED_10000baseT_Full; + + /* Assume PHY must have at least one of PMA/PMD, WIS, PCS, PHY + * XS or DTE XS; give up if none is present. */ + for (mmd = 1; mmd <= 5; mmd++) { + /* Is this MMD present? */ + stat2 = phy_read(phydev, mmd, MDIO_STAT2); + if (stat2 < 0 || + (stat2 & MDIO_STAT2_DEVPRST) != MDIO_STAT2_DEVPRST_VAL) + continue; + + /* It should tell us about all the other MMDs */ + devs1 = phy_read(phydev, mmd, MDIO_DEVS1); + devs2 = phy_read(phydev, mmd, MDIO_DEVS2); + if (devs1 < 0 || devs2 < 0) + continue; + + phydev->mmds = devs1 | (devs2 << 16); + return 0; + } + + return -1; +} + + +static struct phy_driver gen10g_driver = { + .uid = 0xffffffff, + .mask = 0xffffffff, + .name = "Generic 10G PHY", + .features = 0, + .config = gen10g_config, + .startup = gen10g_startup, + .shutdown = gen10g_shutdown, +}; + +/* Generic PHY support and helper functions */ + +/** + * genphy_config_advert - sanitize and advertise auto-negotation parameters + * @phydev: target phy_device struct + * + * Description: Writes MII_ADVERTISE with the appropriate values, + * after sanitizing the values to make sure we only advertise + * what is supported. Returns < 0 on error, 0 if the PHY's advertisement + * hasn't changed, and > 0 if it has changed. + */ +int genphy_config_advert(struct phy_device *phydev) +{ + u32 advertise; + int oldadv, adv; + int err, changed = 0; + + /* Only allow advertising what + * this PHY supports */ + phydev->advertising &= phydev->supported; + advertise = phydev->advertising; + + /* Setup standard advertisement */ + oldadv = adv = phy_read(phydev, MDIO_DEVAD_NONE, MII_ADVERTISE); + + if (adv < 0) + return adv; + + adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4 | ADVERTISE_PAUSE_CAP | + ADVERTISE_PAUSE_ASYM); + if (advertise & ADVERTISED_10baseT_Half) + adv |= ADVERTISE_10HALF; + if (advertise & ADVERTISED_10baseT_Full) + adv |= ADVERTISE_10FULL; + if (advertise & ADVERTISED_100baseT_Half) + adv |= ADVERTISE_100HALF; + if (advertise & ADVERTISED_100baseT_Full) + adv |= ADVERTISE_100FULL; + if (advertise & ADVERTISED_Pause) + adv |= ADVERTISE_PAUSE_CAP; + if (advertise & ADVERTISED_Asym_Pause) + adv |= ADVERTISE_PAUSE_ASYM; + + if (adv != oldadv) { + err = phy_write(phydev, MDIO_DEVAD_NONE, MII_ADVERTISE, adv); + + if (err < 0) + return err; + changed = 1; + } + + /* Configure gigabit if it's supported */ + if (phydev->supported & (SUPPORTED_1000baseT_Half | + SUPPORTED_1000baseT_Full)) { + oldadv = adv = phy_read(phydev, MDIO_DEVAD_NONE, MII_CTRL1000); + + if (adv < 0) + return adv; + + adv &= ~(ADVERTISE_1000FULL | ADVERTISE_1000HALF); + if (advertise & SUPPORTED_1000baseT_Half) + adv |= ADVERTISE_1000HALF; + if (advertise & SUPPORTED_1000baseT_Full) + adv |= ADVERTISE_1000FULL; + + if (adv != oldadv) { + err = phy_write(phydev, MDIO_DEVAD_NONE, MII_CTRL1000, adv); + + if (err < 0) + return err; + changed = 1; + } + } + + return changed; +} + + +/** + * genphy_setup_forced - configures/forces speed/duplex from @phydev + * @phydev: target phy_device struct + * + * Description: Configures MII_BMCR to force speed/duplex + * to the values in phydev. Assumes that the values are valid. + */ +int genphy_setup_forced(struct phy_device *phydev) +{ + int err; + int ctl = 0; + + phydev->pause = phydev->asym_pause = 0; + + if (SPEED_1000 == phydev->speed) + ctl |= BMCR_SPEED1000; + else if (SPEED_100 == phydev->speed) + ctl |= BMCR_SPEED100; + + if (DUPLEX_FULL == phydev->duplex) + ctl |= BMCR_FULLDPLX; + + err = phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, ctl); + + return err; +} + + +/** + * genphy_restart_aneg - Enable and Restart Autonegotiation + * @phydev: target phy_device struct + */ +int genphy_restart_aneg(struct phy_device *phydev) +{ + int ctl; + + ctl = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR); + + if (ctl < 0) + return ctl; + + ctl |= (BMCR_ANENABLE | BMCR_ANRESTART); + + /* Don't isolate the PHY if we're negotiating */ + ctl &= ~(BMCR_ISOLATE); + + ctl = phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, ctl); + + return ctl; +} + + +/** + * genphy_config_aneg - restart auto-negotiation or write BMCR + * @phydev: target phy_device struct + * + * Description: If auto-negotiation is enabled, we configure the + * advertising, and then restart auto-negotiation. If it is not + * enabled, then we write the BMCR. + */ +int genphy_config_aneg(struct phy_device *phydev) +{ + int result; + + if (AUTONEG_ENABLE != phydev->autoneg) + return genphy_setup_forced(phydev); + + result = genphy_config_advert(phydev); + + if (result < 0) /* error */ + return result; + + if (result == 0) { + /* Advertisment hasn't changed, but maybe aneg was never on to + * begin with? Or maybe phy was isolated? */ + int ctl = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR); + + if (ctl < 0) + return ctl; + + if (!(ctl & BMCR_ANENABLE) || (ctl & BMCR_ISOLATE)) + result = 1; /* do restart aneg */ + } + + /* Only restart aneg if we are advertising something different + * than we were before. */ + if (result > 0) + result = genphy_restart_aneg(phydev); + + return result; +} + +/** + * genphy_update_link - update link status in @phydev + * @phydev: target phy_device struct + * + * Description: Update the value in phydev->link to reflect the + * current link value. In order to do this, we need to read + * the status register twice, keeping the second value. + */ +int genphy_update_link(struct phy_device *phydev) +{ + unsigned int mii_reg; + + /* + * Wait if the link is up, and autonegotiation is in progress + * (ie - we're capable and it's not done) + */ + mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR); + + /* + * If we already saw the link up, and it hasn't gone down, then + * we don't need to wait for autoneg again + */ + if (phydev->link && mii_reg & BMSR_LSTATUS) + return 0; + + if ((mii_reg & BMSR_ANEGCAPABLE) && !(mii_reg & BMSR_ANEGCOMPLETE)) { + int i = 0; + + printf("%s Waiting for PHY auto negotiation to complete", + phydev->dev->name); + while (!(mii_reg & BMSR_ANEGCOMPLETE)) { + /* + * Timeout reached ? + */ + if (i > 5000) { + printf(" TIMEOUT !\n"); + phydev->link = 0; + return 0; + } + + if (ctrlc()) { + puts("user interrupt!\n"); + phydev->link = 0; + return -EINTR; + } + + if ((i++ % 500) == 0) + printf("."); + + udelay(1000); /* 1 ms */ + mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR); + } + printf(" done\n"); + phydev->link = 1; + udelay(500000); /* another 500 ms (results in faster booting) */ + } else { + /* Read the link a second time to clear the latched state */ + mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR); + + if (mii_reg & BMSR_LSTATUS) + phydev->link = 1; + else + phydev->link = 0; + } + + return 0; +} + +/* + * Generic function which updates the speed and duplex. If + * autonegotiation is enabled, it uses the AND of the link + * partner's advertised capabilities and our advertised + * capabilities. If autonegotiation is disabled, we use the + * appropriate bits in the control register. + * + * Stolen from Linux's mii.c and phy_device.c + */ +static int genphy_parse_link(struct phy_device *phydev) +{ + int mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR); + + /* We're using autonegotiation */ + if (mii_reg & BMSR_ANEGCAPABLE) { + u32 lpa = 0; + u32 gblpa = 0; + + /* Check for gigabit capability */ + if (mii_reg & BMSR_ERCAP) { + /* We want a list of states supported by + * both PHYs in the link + */ + gblpa = phy_read(phydev, MDIO_DEVAD_NONE, MII_STAT1000); + gblpa &= phy_read(phydev, MDIO_DEVAD_NONE, MII_CTRL1000) << 2; + } + + /* Set the baseline so we only have to set them + * if they're different + */ + phydev->speed = SPEED_10; + phydev->duplex = DUPLEX_HALF; + + /* Check the gigabit fields */ + if (gblpa & (PHY_1000BTSR_1000FD | PHY_1000BTSR_1000HD)) { + phydev->speed = SPEED_1000; + + if (gblpa & PHY_1000BTSR_1000FD) + phydev->duplex = DUPLEX_FULL; + + /* We're done! */ + return 0; + } + + lpa = phy_read(phydev, MDIO_DEVAD_NONE, MII_ADVERTISE); + lpa &= phy_read(phydev, MDIO_DEVAD_NONE, MII_LPA); + + if (lpa & (LPA_100FULL | LPA_100HALF)) { + phydev->speed = SPEED_100; + + if (lpa & LPA_100FULL) + phydev->duplex = DUPLEX_FULL; + + } else if (lpa & LPA_10FULL) + phydev->duplex = DUPLEX_FULL; + } else { + u32 bmcr = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR); + + phydev->speed = SPEED_10; + phydev->duplex = DUPLEX_HALF; + + if (bmcr & BMCR_FULLDPLX) + phydev->duplex = DUPLEX_FULL; + + if (bmcr & BMCR_SPEED1000) + phydev->speed = SPEED_1000; + else if (bmcr & BMCR_SPEED100) + phydev->speed = SPEED_100; + } + + return 0; +} + +int genphy_config(struct phy_device *phydev) +{ + int val; + u32 features; + + /* For now, I'll claim that the generic driver supports + * all possible port types */ + features = (SUPPORTED_TP | SUPPORTED_MII + | SUPPORTED_AUI | SUPPORTED_FIBRE | + SUPPORTED_BNC); + + /* Do we support autonegotiation? */ + val = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR); + + if (val < 0) + return val; + + if (val & BMSR_ANEGCAPABLE) + features |= SUPPORTED_Autoneg; + + if (val & BMSR_100FULL) + features |= SUPPORTED_100baseT_Full; + if (val & BMSR_100HALF) + features |= SUPPORTED_100baseT_Half; + if (val & BMSR_10FULL) + features |= SUPPORTED_10baseT_Full; + if (val & BMSR_10HALF) + features |= SUPPORTED_10baseT_Half; + + if (val & BMSR_ESTATEN) { + val = phy_read(phydev, MDIO_DEVAD_NONE, MII_ESTATUS); + + if (val < 0) + return val; + + if (val & ESTATUS_1000_TFULL) + features |= SUPPORTED_1000baseT_Full; + if (val & ESTATUS_1000_THALF) + features |= SUPPORTED_1000baseT_Half; + } + + phydev->supported = features; + phydev->advertising = features; + + genphy_config_aneg(phydev); + + return 0; +} + +int genphy_startup(struct phy_device *phydev) +{ + genphy_update_link(phydev); + genphy_parse_link(phydev); + + return 0; +} + +int genphy_shutdown(struct phy_device *phydev) +{ + return 0; +} + +static struct phy_driver genphy_driver = { + .uid = 0xffffffff, + .mask = 0xffffffff, + .name = "Generic PHY", + .features = 0, + .config = genphy_config, + .startup = genphy_startup, + .shutdown = genphy_shutdown, +}; + +static struct list_head phy_drivers; + +int phy_init(void) +{ + INIT_LIST_HEAD(&phy_drivers); + + return 0; +} + +int phy_register(struct phy_driver *drv) +{ + INIT_LIST_HEAD(&drv->list); + list_add_tail (&drv->list, &phy_drivers); + + return 0; +} + +int phy_probe(struct phy_device *phydev) +{ + int err = 0; + + phydev->advertising = phydev->supported = phydev->drv->features; + + if (phydev->drv->probe) + err = phydev->drv->probe(phydev); + + return err; +} + +struct phy_driver *get_phy_driver(struct phy_device *phydev, + phy_interface_t interface) +{ + struct list_head *entry; + int phy_id = phydev->phy_id; + struct phy_driver *drv = NULL; + + list_for_each(entry, &phy_drivers) { + drv = list_entry(entry, struct phy_driver, list); + if ((drv->uid & drv->mask) == (phy_id & drv->mask)) + return drv; + } + + /* If we made it here, there's no driver for this PHY */ + if (interface == PHY_INTERFACE_MODE_XGMII) + return &gen10g_driver; + else + return &genphy_driver; +} + +struct phy_device* phy_device_create(struct mii_dev *bus, int addr, int phy_id, + phy_interface_t interface) +{ + struct phy_device *dev; + + /* We allocate the device, and initialize the + * default values */ + dev = malloc(sizeof(*dev)); + if (!dev) { + printf("Failed to allocate PHY device for %s:%d\n", + bus->name, addr); + return NULL; + } + + memset(dev, 0, sizeof(*dev)); + + dev->duplex = -1; + dev->link = 1; + dev->interface = interface; + + dev->autoneg = AUTONEG_ENABLE; + + dev->addr = addr; + dev->phy_id = phy_id; + dev->bus = bus; + + dev->drv = get_phy_driver(dev, interface); + + phy_probe(dev); + + return dev; +} + +/** + * get_phy_id - reads the specified addr for its ID. + * @bus: the target MII bus + * @addr: PHY address on the MII bus + * @phy_id: where to store the ID retrieved. + * + * Description: Reads the ID registers of the PHY at @addr on the + * @bus, stores it in @phy_id and returns zero on success. + */ +int get_phy_id(struct mii_dev *bus, int addr, int devad, u32 *phy_id) +{ + int phy_reg; + + /* Grab the bits from PHYIR1, and put them + * in the upper half */ + phy_reg = bus->read(bus, addr, devad, MII_PHYSID1); + + if (phy_reg < 0) + return -EIO; + + *phy_id = (phy_reg & 0xffff) << 16; + + /* Grab the bits from PHYIR2, and put them in the lower half */ + phy_reg = bus->read(bus, addr, devad, MII_PHYSID2); + + if (phy_reg < 0) + return -EIO; + + *phy_id |= (phy_reg & 0xffff); + + return 0; +} + +/** + * get_phy_device - reads the specified PHY device and returns its @phy_device struct + * @bus: the target MII bus + * @addr: PHY address on the MII bus + * + * Description: Reads the ID registers of the PHY at @addr on the + * @bus, then allocates and returns the phy_device to represent it. + */ +struct phy_device * get_phy_device(struct mii_dev *bus, int addr, + phy_interface_t interface) +{ + u32 phy_id = 0x1fffffff; + int i; + int r; + + /* Try Standard (ie Clause 22) access */ + r = get_phy_id(bus, addr, MDIO_DEVAD_NONE, &phy_id); + if (r) + return NULL; + + /* If the PHY ID is mostly f's, we didn't find anything */ + if ((phy_id & 0x1fffffff) != 0x1fffffff) + return phy_device_create(bus, addr, phy_id, interface); + + /* Otherwise we have to try Clause 45 */ + for (i = 1; i < 5; i++) { + r = get_phy_id(bus, addr, i, &phy_id); + if (r) + return NULL; + + /* If the phy_id is mostly Fs, there is no device there */ + if ((phy_id & 0x1fffffff) != 0x1fffffff) + break; + } + + return phy_device_create(bus, addr, phy_id, interface); +} + +struct phy_device *phy_connect(struct mii_dev *bus, int addr, + struct eth_device *dev, + phy_interface_t interface) +{ + /* Reset the bus */ + bus->reset(bus); + + /* If the PHY is not in the map, probe the PHY to id it */ + if (!bus->phymap[addr]) { + bus->phymap[addr] = get_phy_device(bus, addr, interface); + + if (!bus->phymap[addr]) + printf("Could not get PHY for %s:%d\n", bus->name, addr); + } + + if (bus->phymap[addr]->dev) + printf("%s:%d is connected to %s. Reconnecting to %s\n", + bus->name, addr, bus->phymap[addr]->dev->name, + dev->name); + + bus->phymap[addr]->dev = dev; + + printf("%s connected to %s\n", dev->name, + bus->phymap[addr]->drv->name); + + return bus->phymap[addr]; +} + +int phy_startup(struct phy_device *phydev) +{ + if (phydev->drv->startup) + phydev->drv->startup(phydev); + + return 0; +} + +static int __board_phy_config(struct phy_device *phydev) +{ + return 0; +} + +int board_phy_config(struct phy_device *phydev) + __attribute__((weak, alias("__board_phy_config"))); + +int phy_config(struct phy_device *phydev) +{ + if (phydev->drv->config) + phydev->drv->config(phydev); + + /* Invoke an optional board-specific helper */ + board_phy_config(phydev); + + return 0; +} + +int phy_shutdown(struct phy_device *phydev) +{ + if (phydev->drv->shutdown) + phydev->drv->shutdown(phydev); + + return 0; +} diff --git a/include/miiphy.h b/include/miiphy.h index 42dc127..ea42775 100644 --- a/include/miiphy.h +++ b/include/miiphy.h @@ -34,8 +34,32 @@ #ifndef _miiphy_h_ #define _miiphy_h_
+#include <common.h> #include <linux/mii.h> +#include <linux/list.h> #include <net.h> +#include <phy.h> + +struct legacy_mii_dev { + int (*read) (const char *devname, unsigned char addr, + unsigned char reg, unsigned short *value); + int (*write) (const char *devname, unsigned char addr, + unsigned char reg, unsigned short value); +}; + +#define MDIO_NAME_LEN 32 + +struct mii_dev { + struct list_head link; + char *name; + void *priv; + int (*read) (struct mii_dev *bus, int addr, int devad, int reg); + int (*write) (struct mii_dev *bus, int addr, int devad, int reg, + u16 val); + int (*reset) (struct mii_dev *bus); + struct phy_device *phymap[PHY_MAX_ADDR]; + u32 phy_mask; +};
int miiphy_read (const char *devname, unsigned char addr, unsigned char reg, unsigned short *value); @@ -61,9 +85,16 @@ void miiphy_register (const char *devname,
int miiphy_set_current_dev (const char *devname); const char *miiphy_get_current_dev (void); +struct mii_dev *mdio_get_current_dev (void); +struct mii_dev *miiphy_get_dev_by_name(const char *devname); +struct phy_device *mdio_phydev_for_ethname(const char *devname);
void miiphy_listdev (void);
+struct mii_dev *mdio_alloc(void); +int mdio_register(struct mii_dev *bus); +void mdio_list_devices(void); + #ifdef CONFIG_BITBANGMII
#define BB_MII_DEVNAME "bb_miiphy" diff --git a/include/phy.h b/include/phy.h new file mode 100644 index 0000000..fccf1f7 --- /dev/null +++ b/include/phy.h @@ -0,0 +1,487 @@ +/* + * Copyright 2011 Freescale Semiconductor, Inc. + * Andy Fleming afleming@freescale.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + * This file pretty much stolen from Linux's mii.h/ethtool.h/phy.h + */ + +#ifndef _PHY_H +#define _PHY_H + +#include <linux/list.h> +#include <linux/mii.h> + +/* MDIO Manageable Devices (MMDs). */ +#define MDIO_MMD_PMAPMD 1 /* Physical Medium Attachment/ + * Physical Medium Dependent */ +#define MDIO_MMD_WIS 2 /* WAN Interface Sublayer */ +#define MDIO_MMD_PCS 3 /* Physical Coding Sublayer */ +#define MDIO_MMD_PHYXS 4 /* PHY Extender Sublayer */ +#define MDIO_MMD_DTEXS 5 /* DTE Extender Sublayer */ +#define MDIO_MMD_TC 6 /* Transmission Convergence */ +#define MDIO_MMD_AN 7 /* Auto-Negotiation */ +#define MDIO_MMD_C22EXT 29 /* Clause 22 extension */ +#define MDIO_MMD_VEND1 30 /* Vendor specific 1 */ +#define MDIO_MMD_VEND2 31 /* Vendor specific 2 */ + +/* Generic MDIO registers. */ +#define MDIO_CTRL1 MII_BMCR +#define MDIO_STAT1 MII_BMSR +#define MDIO_DEVID1 MII_PHYSID1 +#define MDIO_DEVID2 MII_PHYSID2 +#define MDIO_SPEED 4 /* Speed ability */ +#define MDIO_DEVS1 5 /* Devices in package */ +#define MDIO_DEVS2 6 +#define MDIO_CTRL2 7 /* 10G control 2 */ +#define MDIO_STAT2 8 /* 10G status 2 */ +#define MDIO_PMA_TXDIS 9 /* 10G PMA/PMD transmit disable */ +#define MDIO_PMA_RXDET 10 /* 10G PMA/PMD receive signal detect */ +#define MDIO_PMA_EXTABLE 11 /* 10G PMA/PMD extended ability */ +#define MDIO_PKGID1 14 /* Package identifier */ +#define MDIO_PKGID2 15 +#define MDIO_AN_ADVERTISE 16 /* AN advertising (base page) */ +#define MDIO_AN_LPA 19 /* AN LP abilities (base page) */ +#define MDIO_PHYXS_LNSTAT 24 /* PHY XGXS lane state */ + +/* Media-dependent registers. */ +#define MDIO_PMA_10GBT_SWAPPOL 130 /* 10GBASE-T pair swap & polarity */ +#define MDIO_PMA_10GBT_TXPWR 131 /* 10GBASE-T TX power control */ +#define MDIO_PMA_10GBT_SNR 133 /* 10GBASE-T SNR margin, lane A. + * Lanes B-D are numbered 134-136. */ +#define MDIO_PMA_10GBR_FECABLE 170 /* 10GBASE-R FEC ability */ +#define MDIO_PCS_10GBX_STAT1 24 /* 10GBASE-X PCS status 1 */ +#define MDIO_PCS_10GBRT_STAT1 32 /* 10GBASE-R/-T PCS status 1 */ +#define MDIO_PCS_10GBRT_STAT2 33 /* 10GBASE-R/-T PCS status 2 */ +#define MDIO_AN_10GBT_CTRL 32 /* 10GBASE-T auto-negotiation control */ +#define MDIO_AN_10GBT_STAT 33 /* 10GBASE-T auto-negotiation status */ + +/* LASI (Link Alarm Status Interrupt) registers, defined by XENPAK MSA. */ +#define MDIO_PMA_LASI_RXCTRL 0x9000 /* RX_ALARM control */ +#define MDIO_PMA_LASI_TXCTRL 0x9001 /* TX_ALARM control */ +#define MDIO_PMA_LASI_CTRL 0x9002 /* LASI control */ +#define MDIO_PMA_LASI_RXSTAT 0x9003 /* RX_ALARM status */ +#define MDIO_PMA_LASI_TXSTAT 0x9004 /* TX_ALARM status */ +#define MDIO_PMA_LASI_STAT 0x9005 /* LASI status */ + +/* Control register 1. */ +/* Enable extended speed selection */ +#define MDIO_CTRL1_SPEEDSELEXT (BMCR_SPEED1000 | BMCR_SPEED100) +/* All speed selection bits */ +#define MDIO_CTRL1_SPEEDSEL (MDIO_CTRL1_SPEEDSELEXT | 0x003c) +#define MDIO_CTRL1_FULLDPLX BMCR_FULLDPLX +#define MDIO_CTRL1_LPOWER BMCR_PDOWN +#define MDIO_CTRL1_RESET BMCR_RESET +#define MDIO_PMA_CTRL1_LOOPBACK 0x0001 +#define MDIO_PMA_CTRL1_SPEED1000 BMCR_SPEED1000 +#define MDIO_PMA_CTRL1_SPEED100 BMCR_SPEED100 +#define MDIO_PCS_CTRL1_LOOPBACK BMCR_LOOPBACK +#define MDIO_PHYXS_CTRL1_LOOPBACK BMCR_LOOPBACK +#define MDIO_AN_CTRL1_RESTART BMCR_ANRESTART +#define MDIO_AN_CTRL1_ENABLE BMCR_ANENABLE +#define MDIO_AN_CTRL1_XNP 0x2000 /* Enable extended next page */ + +/* 10 Gb/s */ +#define MDIO_CTRL1_SPEED10G (MDIO_CTRL1_SPEEDSELEXT | 0x00) +/* 10PASS-TS/2BASE-TL */ +#define MDIO_CTRL1_SPEED10P2B (MDIO_CTRL1_SPEEDSELEXT | 0x04) + +/* Status register 1. */ +#define MDIO_STAT1_LPOWERABLE 0x0002 /* Low-power ability */ +#define MDIO_STAT1_LSTATUS BMSR_LSTATUS +#define MDIO_STAT1_FAULT 0x0080 /* Fault */ +#define MDIO_AN_STAT1_LPABLE 0x0001 /* Link partner AN ability */ +#define MDIO_AN_STAT1_ABLE BMSR_ANEGCAPABLE +#define MDIO_AN_STAT1_RFAULT BMSR_RFAULT +#define MDIO_AN_STAT1_COMPLETE BMSR_ANEGCOMPLETE +#define MDIO_AN_STAT1_PAGE 0x0040 /* Page received */ +#define MDIO_AN_STAT1_XNP 0x0080 /* Extended next page status */ + +/* Speed register. */ +#define MDIO_SPEED_10G 0x0001 /* 10G capable */ +#define MDIO_PMA_SPEED_2B 0x0002 /* 2BASE-TL capable */ +#define MDIO_PMA_SPEED_10P 0x0004 /* 10PASS-TS capable */ +#define MDIO_PMA_SPEED_1000 0x0010 /* 1000M capable */ +#define MDIO_PMA_SPEED_100 0x0020 /* 100M capable */ +#define MDIO_PMA_SPEED_10 0x0040 /* 10M capable */ +#define MDIO_PCS_SPEED_10P2B 0x0002 /* 10PASS-TS/2BASE-TL capable */ + +/* Device present registers. */ +#define MDIO_DEVS_PRESENT(devad) (1 << (devad)) +#define MDIO_DEVS_PMAPMD MDIO_DEVS_PRESENT(MDIO_MMD_PMAPMD) +#define MDIO_DEVS_WIS MDIO_DEVS_PRESENT(MDIO_MMD_WIS) +#define MDIO_DEVS_PCS MDIO_DEVS_PRESENT(MDIO_MMD_PCS) +#define MDIO_DEVS_PHYXS MDIO_DEVS_PRESENT(MDIO_MMD_PHYXS) +#define MDIO_DEVS_DTEXS MDIO_DEVS_PRESENT(MDIO_MMD_DTEXS) +#define MDIO_DEVS_TC MDIO_DEVS_PRESENT(MDIO_MMD_TC) +#define MDIO_DEVS_AN MDIO_DEVS_PRESENT(MDIO_MMD_AN) +#define MDIO_DEVS_C22EXT MDIO_DEVS_PRESENT(MDIO_MMD_C22EXT) +#define MDIO_DEVS_VEND1 MDIO_DEVS_PRESENT(MDIO_MMD_VEND1) +#define MDIO_DEVS_VEND2 MDIO_DEVS_PRESENT(MDIO_MMD_VEND2) + +/* Control register 2. */ +#define MDIO_PMA_CTRL2_TYPE 0x000f /* PMA/PMD type selection */ +#define MDIO_PMA_CTRL2_10GBCX4 0x0000 /* 10GBASE-CX4 type */ +#define MDIO_PMA_CTRL2_10GBEW 0x0001 /* 10GBASE-EW type */ +#define MDIO_PMA_CTRL2_10GBLW 0x0002 /* 10GBASE-LW type */ +#define MDIO_PMA_CTRL2_10GBSW 0x0003 /* 10GBASE-SW type */ +#define MDIO_PMA_CTRL2_10GBLX4 0x0004 /* 10GBASE-LX4 type */ +#define MDIO_PMA_CTRL2_10GBER 0x0005 /* 10GBASE-ER type */ +#define MDIO_PMA_CTRL2_10GBLR 0x0006 /* 10GBASE-LR type */ +#define MDIO_PMA_CTRL2_10GBSR 0x0007 /* 10GBASE-SR type */ +#define MDIO_PMA_CTRL2_10GBLRM 0x0008 /* 10GBASE-LRM type */ +#define MDIO_PMA_CTRL2_10GBT 0x0009 /* 10GBASE-T type */ +#define MDIO_PMA_CTRL2_10GBKX4 0x000a /* 10GBASE-KX4 type */ +#define MDIO_PMA_CTRL2_10GBKR 0x000b /* 10GBASE-KR type */ +#define MDIO_PMA_CTRL2_1000BT 0x000c /* 1000BASE-T type */ +#define MDIO_PMA_CTRL2_1000BKX 0x000d /* 1000BASE-KX type */ +#define MDIO_PMA_CTRL2_100BTX 0x000e /* 100BASE-TX type */ +#define MDIO_PMA_CTRL2_10BT 0x000f /* 10BASE-T type */ +#define MDIO_PCS_CTRL2_TYPE 0x0003 /* PCS type selection */ +#define MDIO_PCS_CTRL2_10GBR 0x0000 /* 10GBASE-R type */ +#define MDIO_PCS_CTRL2_10GBX 0x0001 /* 10GBASE-X type */ +#define MDIO_PCS_CTRL2_10GBW 0x0002 /* 10GBASE-W type */ +#define MDIO_PCS_CTRL2_10GBT 0x0003 /* 10GBASE-T type */ + +/* Status register 2. */ +#define MDIO_STAT2_RXFAULT 0x0400 /* Receive fault */ +#define MDIO_STAT2_TXFAULT 0x0800 /* Transmit fault */ +#define MDIO_STAT2_DEVPRST 0xc000 /* Device present */ +#define MDIO_STAT2_DEVPRST_VAL 0x8000 /* Device present value */ +#define MDIO_PMA_STAT2_LBABLE 0x0001 /* PMA loopback ability */ +#define MDIO_PMA_STAT2_10GBEW 0x0002 /* 10GBASE-EW ability */ +#define MDIO_PMA_STAT2_10GBLW 0x0004 /* 10GBASE-LW ability */ +#define MDIO_PMA_STAT2_10GBSW 0x0008 /* 10GBASE-SW ability */ +#define MDIO_PMA_STAT2_10GBLX4 0x0010 /* 10GBASE-LX4 ability */ +#define MDIO_PMA_STAT2_10GBER 0x0020 /* 10GBASE-ER ability */ +#define MDIO_PMA_STAT2_10GBLR 0x0040 /* 10GBASE-LR ability */ +#define MDIO_PMA_STAT2_10GBSR 0x0080 /* 10GBASE-SR ability */ +#define MDIO_PMD_STAT2_TXDISAB 0x0100 /* PMD TX disable ability */ +#define MDIO_PMA_STAT2_EXTABLE 0x0200 /* Extended abilities */ +#define MDIO_PMA_STAT2_RXFLTABLE 0x1000 /* Receive fault ability */ +#define MDIO_PMA_STAT2_TXFLTABLE 0x2000 /* Transmit fault ability */ +#define MDIO_PCS_STAT2_10GBR 0x0001 /* 10GBASE-R capable */ +#define MDIO_PCS_STAT2_10GBX 0x0002 /* 10GBASE-X capable */ +#define MDIO_PCS_STAT2_10GBW 0x0004 /* 10GBASE-W capable */ +#define MDIO_PCS_STAT2_RXFLTABLE 0x1000 /* Receive fault ability */ +#define MDIO_PCS_STAT2_TXFLTABLE 0x2000 /* Transmit fault ability */ + +/* Transmit disable register. */ +#define MDIO_PMD_TXDIS_GLOBAL 0x0001 /* Global PMD TX disable */ +#define MDIO_PMD_TXDIS_0 0x0002 /* PMD TX disable 0 */ +#define MDIO_PMD_TXDIS_1 0x0004 /* PMD TX disable 1 */ +#define MDIO_PMD_TXDIS_2 0x0008 /* PMD TX disable 2 */ +#define MDIO_PMD_TXDIS_3 0x0010 /* PMD TX disable 3 */ + +/* Receive signal detect register. */ +#define MDIO_PMD_RXDET_GLOBAL 0x0001 /* Global PMD RX signal detect */ +#define MDIO_PMD_RXDET_0 0x0002 /* PMD RX signal detect 0 */ +#define MDIO_PMD_RXDET_1 0x0004 /* PMD RX signal detect 1 */ +#define MDIO_PMD_RXDET_2 0x0008 /* PMD RX signal detect 2 */ +#define MDIO_PMD_RXDET_3 0x0010 /* PMD RX signal detect 3 */ + +/* Extended abilities register. */ +#define MDIO_PMA_EXTABLE_10GCX4 0x0001 /* 10GBASE-CX4 ability */ +#define MDIO_PMA_EXTABLE_10GBLRM 0x0002 /* 10GBASE-LRM ability */ +#define MDIO_PMA_EXTABLE_10GBT 0x0004 /* 10GBASE-T ability */ +#define MDIO_PMA_EXTABLE_10GBKX4 0x0008 /* 10GBASE-KX4 ability */ +#define MDIO_PMA_EXTABLE_10GBKR 0x0010 /* 10GBASE-KR ability */ +#define MDIO_PMA_EXTABLE_1000BT 0x0020 /* 1000BASE-T ability */ +#define MDIO_PMA_EXTABLE_1000BKX 0x0040 /* 1000BASE-KX ability */ +#define MDIO_PMA_EXTABLE_100BTX 0x0080 /* 100BASE-TX ability */ +#define MDIO_PMA_EXTABLE_10BT 0x0100 /* 10BASE-T ability */ + +/* PHY XGXS lane state register. */ +#define MDIO_PHYXS_LNSTAT_SYNC0 0x0001 +#define MDIO_PHYXS_LNSTAT_SYNC1 0x0002 +#define MDIO_PHYXS_LNSTAT_SYNC2 0x0004 +#define MDIO_PHYXS_LNSTAT_SYNC3 0x0008 +#define MDIO_PHYXS_LNSTAT_ALIGN 0x1000 + +/* PMA 10GBASE-T pair swap & polarity */ +#define MDIO_PMA_10GBT_SWAPPOL_ABNX 0x0001 /* Pair A/B uncrossed */ +#define MDIO_PMA_10GBT_SWAPPOL_CDNX 0x0002 /* Pair C/D uncrossed */ +#define MDIO_PMA_10GBT_SWAPPOL_AREV 0x0100 /* Pair A polarity reversed */ +#define MDIO_PMA_10GBT_SWAPPOL_BREV 0x0200 /* Pair B polarity reversed */ +#define MDIO_PMA_10GBT_SWAPPOL_CREV 0x0400 /* Pair C polarity reversed */ +#define MDIO_PMA_10GBT_SWAPPOL_DREV 0x0800 /* Pair D polarity reversed */ + +/* PMA 10GBASE-T TX power register. */ +#define MDIO_PMA_10GBT_TXPWR_SHORT 0x0001 /* Short-reach mode */ + +/* PMA 10GBASE-T SNR registers. */ +/* Value is SNR margin in dB, clamped to range [-127, 127], plus 0x8000. */ +#define MDIO_PMA_10GBT_SNR_BIAS 0x8000 +#define MDIO_PMA_10GBT_SNR_MAX 127 + +/* PMA 10GBASE-R FEC ability register. */ +#define MDIO_PMA_10GBR_FECABLE_ABLE 0x0001 /* FEC ability */ +#define MDIO_PMA_10GBR_FECABLE_ERRABLE 0x0002 /* FEC error indic. ability */ + +/* PCS 10GBASE-R/-T status register 1. */ +#define MDIO_PCS_10GBRT_STAT1_BLKLK 0x0001 /* Block lock attained */ + +/* PCS 10GBASE-R/-T status register 2. */ +#define MDIO_PCS_10GBRT_STAT2_ERR 0x00ff +#define MDIO_PCS_10GBRT_STAT2_BER 0x3f00 + +/* AN 10GBASE-T control register. */ +#define MDIO_AN_10GBT_CTRL_ADV10G 0x1000 /* Advertise 10GBASE-T */ + +/* AN 10GBASE-T status register. */ +#define MDIO_AN_10GBT_STAT_LPTRR 0x0200 /* LP training reset req. */ +#define MDIO_AN_10GBT_STAT_LPLTABLE 0x0400 /* LP loop timing ability */ +#define MDIO_AN_10GBT_STAT_LP10G 0x0800 /* LP is 10GBT capable */ +#define MDIO_AN_10GBT_STAT_REMOK 0x1000 /* Remote OK */ +#define MDIO_AN_10GBT_STAT_LOCOK 0x2000 /* Local OK */ +#define MDIO_AN_10GBT_STAT_MS 0x4000 /* Master/slave config */ +#define MDIO_AN_10GBT_STAT_MSFLT 0x8000 /* Master/slave config fault */ + +/* LASI RX_ALARM control/status registers. */ +#define MDIO_PMA_LASI_RX_PHYXSLFLT 0x0001 /* PHY XS RX local fault */ +#define MDIO_PMA_LASI_RX_PCSLFLT 0x0008 /* PCS RX local fault */ +#define MDIO_PMA_LASI_RX_PMALFLT 0x0010 /* PMA/PMD RX local fault */ +#define MDIO_PMA_LASI_RX_OPTICPOWERFLT 0x0020 /* RX optical power fault */ +#define MDIO_PMA_LASI_RX_WISLFLT 0x0200 /* WIS local fault */ + +/* LASI TX_ALARM control/status registers. */ +#define MDIO_PMA_LASI_TX_PHYXSLFLT 0x0001 /* PHY XS TX local fault */ +#define MDIO_PMA_LASI_TX_PCSLFLT 0x0008 /* PCS TX local fault */ +#define MDIO_PMA_LASI_TX_PMALFLT 0x0010 /* PMA/PMD TX local fault */ +#define MDIO_PMA_LASI_TX_LASERPOWERFLT 0x0080 /* Laser output power fault */ +#define MDIO_PMA_LASI_TX_LASERTEMPFLT 0x0100 /* Laser temperature fault */ +#define MDIO_PMA_LASI_TX_LASERBICURRFLT 0x0200 /* Laser bias current fault */ + +/* LASI control/status registers. */ +#define MDIO_PMA_LASI_LSALARM 0x0001 /* LS_ALARM enable/status */ +#define MDIO_PMA_LASI_TXALARM 0x0002 /* TX_ALARM enable/status */ +#define MDIO_PMA_LASI_RXALARM 0x0004 /* RX_ALARM enable/status */ + +/* Mapping between MDIO PRTAD/DEVAD and mii_ioctl_data::phy_id */ + +#define MDIO_PHY_ID_C45 0x8000 +#define MDIO_PHY_ID_PRTAD 0x03e0 +#define MDIO_PHY_ID_DEVAD 0x001f +#define MDIO_PHY_ID_C45_MASK \ + (MDIO_PHY_ID_C45 | MDIO_PHY_ID_PRTAD | MDIO_PHY_ID_DEVAD) + +/* Indicates what features are supported by the interface. */ +#define SUPPORTED_10baseT_Half (1 << 0) +#define SUPPORTED_10baseT_Full (1 << 1) +#define SUPPORTED_100baseT_Half (1 << 2) +#define SUPPORTED_100baseT_Full (1 << 3) +#define SUPPORTED_1000baseT_Half (1 << 4) +#define SUPPORTED_1000baseT_Full (1 << 5) +#define SUPPORTED_Autoneg (1 << 6) +#define SUPPORTED_TP (1 << 7) +#define SUPPORTED_AUI (1 << 8) +#define SUPPORTED_MII (1 << 9) +#define SUPPORTED_FIBRE (1 << 10) +#define SUPPORTED_BNC (1 << 11) +#define SUPPORTED_10000baseT_Full (1 << 12) +#define SUPPORTED_Pause (1 << 13) +#define SUPPORTED_Asym_Pause (1 << 14) +#define SUPPORTED_2500baseX_Full (1 << 15) +#define SUPPORTED_Backplane (1 << 16) +#define SUPPORTED_1000baseKX_Full (1 << 17) +#define SUPPORTED_10000baseKX4_Full (1 << 18) +#define SUPPORTED_10000baseKR_Full (1 << 19) +#define SUPPORTED_10000baseR_FEC (1 << 20) + +/* Indicates what features are advertised by the interface. */ +#define ADVERTISED_10baseT_Half (1 << 0) +#define ADVERTISED_10baseT_Full (1 << 1) +#define ADVERTISED_100baseT_Half (1 << 2) +#define ADVERTISED_100baseT_Full (1 << 3) +#define ADVERTISED_1000baseT_Half (1 << 4) +#define ADVERTISED_1000baseT_Full (1 << 5) +#define ADVERTISED_Autoneg (1 << 6) +#define ADVERTISED_TP (1 << 7) +#define ADVERTISED_AUI (1 << 8) +#define ADVERTISED_MII (1 << 9) +#define ADVERTISED_FIBRE (1 << 10) +#define ADVERTISED_BNC (1 << 11) +#define ADVERTISED_10000baseT_Full (1 << 12) +#define ADVERTISED_Pause (1 << 13) +#define ADVERTISED_Asym_Pause (1 << 14) +#define ADVERTISED_2500baseX_Full (1 << 15) +#define ADVERTISED_Backplane (1 << 16) +#define ADVERTISED_1000baseKX_Full (1 << 17) +#define ADVERTISED_10000baseKX4_Full (1 << 18) +#define ADVERTISED_10000baseKR_Full (1 << 19) +#define ADVERTISED_10000baseR_FEC (1 << 20) + +/* The following are all involved in forcing a particular link + * mode for the device for setting things. When getting the + * devices settings, these indicate the current mode and whether + * it was foced up into this mode or autonegotiated. + */ + +/* The forced speed, 10Mb, 100Mb, gigabit, 2.5Gb, 10GbE. */ +#define SPEED_10 10 +#define SPEED_100 100 +#define SPEED_1000 1000 +#define SPEED_2500 2500 +#define SPEED_10000 10000 + +/* Duplex, half or full. */ +#define DUPLEX_HALF 0x00 +#define DUPLEX_FULL 0x01 + +/* Which connector port. */ +#define PORT_TP 0x00 +#define PORT_AUI 0x01 +#define PORT_MII 0x02 +#define PORT_FIBRE 0x03 +#define PORT_BNC 0x04 +#define PORT_DA 0x05 +#define PORT_NONE 0xef +#define PORT_OTHER 0xff + +/* Which transceiver to use. */ +#define XCVR_INTERNAL 0x00 +#define XCVR_EXTERNAL 0x01 +#define XCVR_DUMMY1 0x02 +#define XCVR_DUMMY2 0x03 +#define XCVR_DUMMY3 0x04 + +/* Enable or disable autonegotiation. If this is set to enable, + * the forced link modes above are completely ignored. + */ +#define AUTONEG_DISABLE 0x00 +#define AUTONEG_ENABLE 0x01 + +#define MDIO_DEVAD_NONE -1 +#define PHY_MAX_ADDR 32 + +#define PHY_BASIC_FEATURES (SUPPORTED_10baseT_Half | \ + SUPPORTED_10baseT_Full | \ + SUPPORTED_100baseT_Half | \ + SUPPORTED_100baseT_Full | \ + SUPPORTED_Autoneg | \ + SUPPORTED_TP | \ + SUPPORTED_MII) + +#define PHY_GBIT_FEATURES (PHY_BASIC_FEATURES | \ + SUPPORTED_1000baseT_Half | \ + SUPPORTED_1000baseT_Full) + +#define PHY_10G_FEATURES (PHY_GBIT_FEATURES | \ + SUPPORTED_10000baseT_Full) + + +typedef enum { + PHY_INTERFACE_MODE_MII, + PHY_INTERFACE_MODE_GMII, + PHY_INTERFACE_MODE_SGMII, + PHY_INTERFACE_MODE_TBI, + PHY_INTERFACE_MODE_RMII, + PHY_INTERFACE_MODE_RGMII, + PHY_INTERFACE_MODE_RGMII_ID, + PHY_INTERFACE_MODE_RGMII_RXID, + PHY_INTERFACE_MODE_RGMII_TXID, + PHY_INTERFACE_MODE_RTBI, + PHY_INTERFACE_MODE_XGMII +} phy_interface_t; + +struct phy_device; + +/* struct phy_driver: a structure which defines PHY behavior + * + * uid will contain a number which represents the PHY. During + * startup, the driver will poll the PHY to find out what its + * UID--as defined by registers 2 and 3--is. The 32-bit result + * gotten from the PHY will be masked to + * discard any bits which may change based on revision numbers + * unimportant to functionality + * + */ +struct phy_driver { + char *name; + unsigned int uid; + unsigned int mask; + + u32 features; + + /* Called to do any driver startup necessities */ + /* Will be called during phy_connect */ + int (*probe)(struct phy_device *phydev); + + /* Called to configure the PHY, and modify the controller + * based on the results. Should be called after phy_connect */ + int (*config)(struct phy_device *phydev); + + /* Called when starting up the controller */ + int (*startup)(struct phy_device *phydev); + + /* Called when bringing down the controller */ + int (*shutdown)(struct phy_device *phydev); + + struct list_head list; +}; + +struct phy_device { + /* Information about the PHY type */ + /* And management functions */ + struct mii_dev *bus; + struct phy_driver *drv; + void *priv; + + struct eth_device *dev; + + /* forced speed & duplex (no autoneg) + * partner speed & duplex & pause (autoneg) + */ + int speed; + int duplex; + + /* The most recently read link state */ + int link; + int port; + phy_interface_t interface; + + u32 advertising; + u32 supported; + u32 mmds; + + int autoneg; + int addr; + int pause; + int asym_pause; + u32 phy_id; + u32 flags; +}; + +int phy_init(void); +struct phy_device *phy_connect(struct mii_dev *bus, int addr, + struct eth_device *dev, + phy_interface_t interface); +int phy_startup(struct phy_device *phydev); +int phy_config(struct phy_device *phydev); +int phy_shutdown(struct phy_device *phydev); +int phy_write(struct phy_device *phydev, int devad, int reg, u16 val); +int phy_read(struct phy_device *phydev, int devad, int reg); +int phy_register(struct phy_driver *drv); +int genphy_config_aneg(struct phy_device *phydev); +int genphy_update_link(struct phy_device *phydev); +int genphy_config(struct phy_device *phydev); +int genphy_startup(struct phy_device *phydev); +int genphy_shutdown(struct phy_device *phydev); +int gen10g_config(struct phy_device *phydev); +int gen10g_startup(struct phy_device *phydev); +int gen10g_shutdown(struct phy_device *phydev); +#endif diff --git a/net/eth.c b/net/eth.c index 3a7ff50..6523834 100644 --- a/net/eth.c +++ b/net/eth.c @@ -25,6 +25,7 @@ #include <command.h> #include <net.h> #include <miiphy.h> +#include <phy.h>
void eth_parse_enetaddr(const char *addr, uchar *enetaddr) { @@ -217,6 +218,11 @@ int eth_initialize(bd_t *bis) #if defined(CONFIG_MII) || defined(CONFIG_CMD_MII) miiphy_init(); #endif + +#ifdef CONFIG_PHYLIB + phy_init(); +#endif + /* * If board-specific initialization exists, call it. * If not, call a CPU-specific one