Hello Fabio,
Am 12.11.2020 um 03:11 schrieb Fabio Estevam:
Hi,
I am trying to load SPL and u-boot-dtb.img via USB using the imx_usb_loader tool.
Running the latest mainline U-Boot on a imx6q-sabresd I get:
$ sudo ./imx_usb SPL
On the console:
U-Boot SPL 2021.01-rc2-00005-g832bfad7451e (Nov 11 2020 - 23:00:05 -0300) Trying to boot from USB SDP SDP: initialize... SDP: handle requests...
Then I try to load u-boot-dtb.img and the following is seen on the host PC:
$ sudo ./imx_usb u-boot-dtb.img config file </usr/etc/imx-loader.d//imx_usb.conf> vid=0x066f pid=0x3780 file_name=mx23_usb_work.conf vid=0x15a2 pid=0x004f file_name=mx28_usb_work.conf vid=0x15a2 pid=0x0052 file_name=mx50_usb_work.conf vid=0x15a2 pid=0x0054 file_name=mx6_usb_work.conf vid=0x15a2 pid=0x0061 file_name=mx6_usb_work.conf vid=0x15a2 pid=0x0063 file_name=mx6_usb_work.conf vid=0x15a2 pid=0x0071 file_name=mx6_usb_work.conf vid=0x15a2 pid=0x007d file_name=mx6_usb_work.conf vid=0x15a2 pid=0x0080 file_name=mx6_usb_work.conf vid=0x1fc9 pid=0x0128 file_name=mx6_usb_work.conf vid=0x15a2 pid=0x0076 file_name=mx7_usb_work.conf vid=0x1fc9 pid=0x0126 file_name=mx7ulp_usb_work.conf vid=0x15a2 pid=0x0041 file_name=mx51_usb_work.conf vid=0x15a2 pid=0x004e file_name=mx53_usb_work.conf vid=0x15a2 pid=0x006a file_name=vybrid_usb_work.conf vid=0x066f pid=0x37ff file_name=linux_gadget.conf vid=0x1b67 pid=0x4fff file_name=mx6_usb_sdp_spl.conf vid=0x0525 pid=0xb4a4 file_name=mx6_usb_sdp_spl.conf vid=0x1fc9 pid=0x012b file_name=mx8mq_usb_work.conf config file </usr/etc/imx-loader.d//mx6_usb_sdp_spl.conf> parse /usr/etc/imx-loader.d//mx6_usb_sdp_spl.conf Trying to open device vid=0x0525 pid=0xb4a4 Interface 0 claimed HAB security state: development mode (0x56787856) == work item filename u-boot-dtb.img load_size 0 bytes load_addr 0x00000000 dcd 1 clear_dcd 0 plug 1 jump_mode 3 jump_addr 0x00000000 == end work item header not found 8400:2e77d044, 4000 do_download failed, err=-22 HAB security state: development mode (0x56787856)
And nothing else appears in the console.
I tried to bisect, but the latest version I got this to run was v2019.01, which was not using the driver model and prevents bisection.
Does anyone have any suggestions?
Hmm... just tried cuurent mainline on an imx6ull based board, works fine for me, see log [1] ... Ok, I boot signed image: u-boot-ivt.img.signed
(Board is not yet in mainline ... but no special change regarding USB, only dts and board code ...)
bye, Heiko [1] boot SPL/U-Boot with imx_usb_loader
$ tbot @argsk30rfdevboard-local interactive_uboot -f usbloader tbot starting ... ├─Flags: │ 'do_power', 'usbloader', 'local', 'threadripper-big-build' ├─Calling interactive_uboot ... │ ├─[lab3] sudo ifconfig eth0 down 192.168.3.1 up │ ├─[lab3] sudo ifconfig eth0 down 192.168.3.1 up │ ├─[lab3] kermit /home/pi/kermrc_k30rf-devboard │ ├─POWERON (k30rf-devboard) │ ├─[lab3] sispmctl -D 01:01:5c:29:39 -o 2 │ │ ## Accessing Gembird #0 USB device 005 │ │ ## Switched outlet 2 on │ ├─[lab3] sudo /home/pi/source/imx_usb_loader/imx_usb /srv/tftpboot/imx6ull_pat_defconfig/20201016/SPL.signed │ │ ## config file </home/pi/source/imx_usb_loader//imx_usb.conf> │ │ ## vid=0x066f pid=0x3780 file_name=mx23_usb_work.conf │ │ ## vid=0x15a2 pid=0x004f file_name=mx28_usb_work.conf │ │ ## vid=0x15a2 pid=0x0052 file_name=mx50_usb_work.conf │ │ ## vid=0x15a2 pid=0x0054 file_name=mx6_usb_work.conf │ │ ## vid=0x15a2 pid=0x0061 file_name=mx6_usb_work.conf │ │ ## vid=0x15a2 pid=0x0063 file_name=mx6_usb_work.conf │ │ ## vid=0x15a2 pid=0x0071 file_name=mx6_usb_work.conf │ │ ## vid=0x15a2 pid=0x007d file_name=mx6_usb_work.conf │ │ ## vid=0x15a2 pid=0x0080 file_name=mx6ull_usb_work.conf │ │ ## vid=0x1fc9 pid=0x0128 file_name=mx6_usb_work.conf │ │ ## vid=0x15a2 pid=0x0076 file_name=mx7_usb_work.conf │ │ ## vid=0x1fc9 pid=0x0126 file_name=mx7ulp_usb_work.conf │ │ ## vid=0x15a2 pid=0x0041 file_name=mx51_usb_work.conf │ │ ## vid=0x15a2 pid=0x004e file_name=mx53_usb_work.conf │ │ ## vid=0x15a2 pid=0x006a file_name=vybrid_usb_work.conf │ │ ## vid=0x066f pid=0x37ff file_name=linux_gadget.conf │ │ ## vid=0x1b67 pid=0x4fff file_name=mx6_usb_sdp_spl.conf │ │ ## vid=0x0525 pid=0xb4a4 file_name=mx6_usb_sdp_spl.conf │ │ ## vid=0x1fc9 pid=0x012b file_name=mx8mq_usb_work.conf │ │ ## vid=0x1fc9 pid=0x0134 file_name=mx8mm_usb_work.conf │ │ ## vid=0x1fc9 pid=0x013e file_name=mx8mn_usb_work.conf │ │ ## vid=0x3016 pid=0x1001 file_name=mx8m_usb_sdp_spl.conf │ │ ## config file </home/pi/source/imx_usb_loader//mx6ull_usb_work.conf> │ │ ## parse /home/pi/source/imx_usb_loader//mx6ull_usb_work.conf │ │ ## Trying to open device vid=0x15a2 pid=0x0080 │ │ ## Interface 0 claimed │ │ ## HAB security state: development mode (0x56787856) │ │ ## == work item │ │ ## filename /srv/tftpboot/imx6ull_pat_defconfig/20201016/SPL.signed │ │ ## load_size 0 bytes │ │ ## load_addr 0x00000000 │ │ ## dcd 1 │ │ ## clear_dcd 0 │ │ ## plug 1 │ │ ## jump_mode 3 │ │ ## jump_addr 0x00000000 │ │ ## == end work item │ │ ## No DCD table │ │ ## │ │ ## loading binary file(/srv/tftpboot/imx6ull_pat_defconfig/20201016/SPL.signed) to 00907400, skip=0, fsize=f540 type=aa │ │ ## │ │ ## <<<62784, 62784 bytes>>> │ │ ## succeeded (security 0x56787856, status 0x88888888) │ │ ## jumping to 0x00907400 │ ├─[lab3] sudo /home/pi/source/imx_usb_loader/imx_usb /srv/tftpboot/imx6ull_pat_defconfig/20201016/u-boot-ivt.img.signed │ │ ## config file </home/pi/source/imx_usb_loader//imx_usb.conf> │ │ ## vid=0x066f pid=0x3780 file_name=mx23_usb_work.conf │ │ ## vid=0x15a2 pid=0x004f file_name=mx28_usb_work.conf │ │ ## vid=0x15a2 pid=0x0052 file_name=mx50_usb_work.conf │ │ ## vid=0x15a2 pid=0x0054 file_name=mx6_usb_work.conf │ │ ## vid=0x15a2 pid=0x0061 file_name=mx6_usb_work.conf │ │ ## vid=0x15a2 pid=0x0063 file_name=mx6_usb_work.conf │ │ ## vid=0x15a2 pid=0x0071 file_name=mx6_usb_work.conf │ │ ## vid=0x15a2 pid=0x007d file_name=mx6_usb_work.conf │ │ ## vid=0x15a2 pid=0x0080 file_name=mx6ull_usb_work.conf │ │ ## vid=0x1fc9 pid=0x0128 file_name=mx6_usb_work.conf │ │ ## vid=0x15a2 pid=0x0076 file_name=mx7_usb_work.conf │ │ ## vid=0x1fc9 pid=0x0126 file_name=mx7ulp_usb_work.conf │ │ ## vid=0x15a2 pid=0x0041 file_name=mx51_usb_work.conf │ │ ## vid=0x15a2 pid=0x004e file_name=mx53_usb_work.conf │ │ ## vid=0x15a2 pid=0x006a file_name=vybrid_usb_work.conf │ │ ## vid=0x066f pid=0x37ff file_name=linux_gadget.conf │ │ ## vid=0x1b67 pid=0x4fff file_name=mx6_usb_sdp_spl.conf │ │ ## vid=0x0525 pid=0xb4a4 file_name=mx6_usb_sdp_spl.conf │ │ ## vid=0x1fc9 pid=0x012b file_name=mx8mq_usb_work.conf │ │ ## vid=0x1fc9 pid=0x0134 file_name=mx8mm_usb_work.conf │ │ ## vid=0x1fc9 pid=0x013e file_name=mx8mn_usb_work.conf │ │ ## vid=0x3016 pid=0x1001 file_name=mx8m_usb_sdp_spl.conf │ │ ## config file </home/pi/source/imx_usb_loader//mx6_usb_sdp_spl.conf> │ │ ## parse /home/pi/source/imx_usb_loader//mx6_usb_sdp_spl.conf │ │ ## Trying to open device vid=0x0525 pid=0xb4a4 │ │ ## Interface 0 claimed │ │ ## HAB security state: development mode (0x56787856) │ │ ## == work item │ │ ## filename /srv/tftpboot/imx6ull_pat_defconfig/20201016/u-boot-ivt.img.signed │ │ ## load_size 0 bytes │ │ ## load_addr 0x00000000 │ │ ## dcd 1 │ │ ## clear_dcd 0 │ │ ## plug 1 │ │ ## jump_mode 3 │ │ ## jump_addr 0x00000000 │ │ ## == end work item │ │ ## │ │ ## loading binary file(/srv/tftpboot/imx6ull_pat_defconfig/20201016/u-boot-ivt.img.signed) to 84ffffc0, skip=0, fsize=94960 type=aa │ │ ## │ │ ## <<<608608, 608608 bytes>>> │ │ ## succeeded (security 0x56787856, status 0x88888888) │ │ ## jumping to 0x84ffffc0 │ ├─UBOOT (k30rfdev-uboot) │ │ <> 18 │ │ <> OpenSSL versions prior to 1.0.0 must be the same. │ │ <> Set LD_LIBRARY_PATH for OpenSSL 1.0.2j 26 Sep 2016. │ │ <> Or rebuild C-Kermit from source on this computer to make versions agree. │ │ <> C-Kermit makefile target: linux+krb5+openssl │ │ <> Or if that is what you did then try to find out why │ │ <> the program loader (image activator) is choosing a │ │ <> different OpenSSL library than the one specified in the build. │ │ <> │ │ <> All SSL/TLS features disabled. │ │ <> │ │ <> Connecting to /dev/serial/by-id/usb-FTDI_TTL232R-3V3_FTBQ76YJ-if00-port0, speed 115200 │ │ <> Escape character: Ctrl-\ (ASCII 28, FS): enabled │ │ <> Type the escape character followed by C to get back, │ │ <> or followed by ? to see other options. │ │ <> ---------------------------------------------------- │ │ <> �� │ │ <> U-Boot SPL 2021.01-rc2-development-00017-gf4ab9f8665-dirty (Nov 12 2020 - 06:03:54 +0100) │ │ <> Trying to boot from MMC1 │ │ <> Card did not respond to voltage select! │ │ <> spl: mmc init failed with error: -95 │ │ <> Trying to boot from SPI │ │ <> Trying to boot from USB SDP │ │ <> SDP: initialize... │ │ <> SDP: handle requests... │ │ <> Downloading file of size 608608 to 0x84ffffc0... done │ │ <> Jumping to header at 0x84ffffc0 │ │ <> Header Tag is not an IMX image │ │ <> Found header at 0x84ffffc0 │ │ <> hab fuse not enabled │ │ <> │ │ <> Authenticate image from DDR location 0x84ffffc0... │ │ <> │ │ <> │ │ <> U-Boot 2021.01-rc2-development-00017-gf4ab9f8665-dirty (Nov 12 2020 - 06:03:54 +0100) │ │ <> │ │ <> CPU: Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz) │ │ <> CPU: Industrial temperature grade (-40C to 105C) at 26C │ │ <> Reset cause: POR │ │ <> Model: xxx patdevboard imx6ull board │ │ <> Board: pat-devboard │ │ <> Devel version, do not use in production! │ │ <> DRAM: 128 MiB │ │ <> WDT: Started with servicing (90s timeout) │ │ <> NAND: 512 MiB │ │ <> MMC: FSL_SDHC: 0 │ │ <> Loading Environment from nowhere... OK │ │ <> Loading Environment from SPIFlash... SF: Detected s25fl128l with page size 256 Bytes, erase size 4 KiB, total 16 MiB │ │ <> OK │ │ <> In: serial@21f4000 │ │ <> Out: serial@21f4000 │ │ <> Err: serial@21f4000 │ │ <> Net: usb_ether │ │ <> Hit any key to stop autoboot: 0 │ │ <> DEVEL: autoboot failed, go to cmdline │ │ <> => │ ├─[k30rfdev-uboot] setenv rescuetftp run loadrescuetftp ramargs addcon addmtd addmisc;bootm ${loadaddr} │ ├─Entering interactive shell (CTRL+D to exit) ...
=>