Hi Jagan,
On Wed, 2014-01-08 at 17:43 +0530, Jagan Teki wrote:
Hi Chin Liang See,
On Thu, Jan 2, 2014 at 8:13 AM, Chin Liang See clsee@altera.com wrote:
To add the Cadence SPI driver support for Altera SOCFPGA. It required information such as clocks and timing from platform's configuration header file within include/configs folder
Signed-off-by: Chin Liang See clsee@altera.com Cc: Jagan Teki jagannadh.teki@gmail.com Cc: Gerhard Sittig gsi@denx.de
Changes for v2
- Combine driver into single C file instead of 2
- Added documentation on the macro used
- Using structure for registers instead of macro
doc/README.socfpga | 47 ++ drivers/spi/Makefile | 1 + drivers/spi/cadence_qspi.c | 1018 ++++++++++++++++++++++++++++++++++++++++++++ drivers/spi/cadence_qspi.h | 170 ++++++++ 4 files changed, 1236 insertions(+) create mode 100644 drivers/spi/cadence_qspi.c create mode 100644 drivers/spi/cadence_qspi.h
diff --git a/doc/README.socfpga b/doc/README.socfpga index cfcbbfe..242af97 100644 --- a/doc/README.socfpga +++ b/doc/README.socfpga @@ -51,3 +51,50 @@ the card #define CONFIG_SOCFPGA_DWMMC_BUS_HZ 50000000 -> The clock rate to controller. Do note the controller have a wrapper which divide the clock from PLL by 4.
+-------------------------------------------- +cadence_qspi +-------------------------------------------- +Here are macro and detailed configuration required to enable Cadence QSPI +controller support within SOCFPGA
+#define CONFIG_SPI_FLASH +-> To enable the SPI flash framework support
+#define CONFIG_CMD_SF +-> To enable the console support for SPI flash
+#define CONFIG_SF_DEFAULT_SPEED (50000000) +-> To set the target SPI clock frequency in Hz
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 +-> To set the SPI mode (CPOL & CPHA). Normally use mode 3 for serial NOR flash
+#define CONFIG_SPI_FLASH_QUAD (1) +-> To enable the Quad IO mode for performance boost
+#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SPI_FLASH_SPANSION +-> To enable the SPI flash support for vendor Micron and Spansion
+#define CONFIG_CQSPI_BASE (SOCFPGA_QSPIREGS_ADDRESS) +#define CONFIG_CQSPI_AHB_BASE (SOCFPGA_QSPIDATA_ADDRESS) +-> To specify the base address for controller CSR base and AHB data base addr
+#define CONFIG_CQSPI_REF_CLK (400000000) +-> The clock frequency supplied from PLL to the QSPI controller
+#define CONFIG_CQSPI_PAGE_SIZE (256) +-> To define the page size of serial flash in bytes
+#define CONFIG_CQSPI_BLOCK_SIZE (16) +-> To define the block size of serial flash in pages
+#define CONFIG_CQSPI_DECODER (0) +-> To enable the 4-to-16 decoder which enable up to 16 serial flash devices
+#define CONFIG_CQSPI_TSHSL_NS (200) +#define CONFIG_CQSPI_TSD2D_NS (255) +#define CONFIG_CQSPI_TCHSH_NS (20) +#define CONFIG_CQSPI_TSLCH_NS (20) +-> Configure the controller based on serial flash device timing characteristic
Do we really require this, because most of the known macros definitions. Better to not write too many duplicates - Yes there are few macro's which are specific to cadence but I don't think those were required.
Oh actually this is to address Gerhard's comment. This document will guide user the required macro (and its details) in order to use this Cadence QSPI controller.
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index ed4ecd7..b8d56ea 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_ATMEL_DATAFLASH_SPI) += atmel_dataflash_spi.o obj-$(CONFIG_ATMEL_SPI) += atmel_spi.o obj-$(CONFIG_BFIN_SPI) += bfin_spi.o obj-$(CONFIG_BFIN_SPI6XX) += bfin_spi6xx.o +obj-$(CONFIG_CADENCE_QSPI) += cadence_qspi.o obj-$(CONFIG_CF_SPI) += cf_spi.o obj-$(CONFIG_CF_QSPI) += cf_qspi.o obj-$(CONFIG_DAVINCI_SPI) += davinci_spi.o diff --git a/drivers/spi/cadence_qspi.c b/drivers/spi/cadence_qspi.c new file mode 100644 index 0000000..4712b45 --- /dev/null +++ b/drivers/spi/cadence_qspi.c @@ -0,0 +1,1018 @@ +/*
- (C) Copyright 2014 Altera Corporation <www.altera.com>
- SPDX-License-Identifier: GPL-2.0+
- */
+#include <common.h> +#include <asm/io.h> +#include <asm/errno.h> +#include <malloc.h> +#include <spi.h> +#include "cadence_qspi.h"
Try to move the stuff from header here.!
Actually I was doing this initially but it bloated this c file a lot. Hopefully its ok that we separate out to a header file. But if you think this is required, I can make the v3.
Thanks
Chin Liang