On Mon, Apr 06, 2020 at 05:58:31PM +0530, Amit Singh Tomar wrote:
This adds build and flash steps for Actions S700 based Cubieboard7 board.
Signed-off-by: Amit Singh Tomar amittomer25@gmail.com
Reviewed-by: Manivannan Sadhasivam manivannan.sadhasivam@linaro.org
Thanks, Mani
Changes since v9:
- Updated the heading to CUBIEBOARD7 to ACTIONS.
- Added shorthand for mkimage command.
Changes since v8: * No changes. Changes since v7: * No changes. Changes since v6: * No changes. Changes since v5: * No changes. Changes since v4: * No changes. Changes since v3: * Convert plain text documentation to reStructuredText format. Changes since v2: * No Change. Changes since v1: * No Change.
doc/board/actions/cubieboard7.rst | 114 ++++++++++++++++++++++++++++++++++++++ doc/board/actions/index.rst | 10 ++++ doc/board/index.rst | 1 + 3 files changed, 125 insertions(+) create mode 100644 doc/board/actions/cubieboard7.rst create mode 100644 doc/board/actions/index.rst
diff --git a/doc/board/actions/cubieboard7.rst b/doc/board/actions/cubieboard7.rst new file mode 100644 index 0000000..e01d2d0 --- /dev/null +++ b/doc/board/actions/cubieboard7.rst @@ -0,0 +1,114 @@ +.. SPDX-License-Identifier: GPL-2.0+ +.. Copyright (C) 2020 Amit Singh Tomar amittomer25@gmail.com
+CUBIEBOARD7 +===========
+About this +----------
+This document describes build and flash steps for Actions S700 SoC based Cubieboard7 +board.
+Cubieboard7 initial configuration +---------------------------------
+Default Cubieboard7 comes with pre-installed Android where U-Boot is configured with +a bootdelay of 0, entering a prompt by pressing keys does not seem to work.
+Though, one can enter ADFU mode and flash debian image(from host machine) where +getting into u-boot prompt is easy.
+Enter ADFU Mode +----------------
+Before write the firmware, let the development board entering the ADFU mode: insert +one end of the USB cable to the PC, press and hold the ADFU button, and then connect +the other end of the USB cable to the Mini USB port of the development board, release +the ADFU button, after connecting it will enter the ADFU mode.
+Check whether entered ADFU Mode +--------------------------------
+The user needs to run the following command on the PC side to check if the ADFU +device is detected. ID realted to "Actions Semiconductor Co., Ltd" means that +the PC side has been correctly detected ADFU device, the development board +also enter into the ADFU mode.
+.. code-block:: none
- $ lsusb
- Bus 001 Device 005: ID 04f2:b2eb Chicony Electronics Co., Ltd
- Bus 001 Device 004: ID 0a5c:21e6 Broadcom Corp. BCM20702 Bluetooth 4.0 [ThinkPad]
- Bus 001 Device 003: ID 046d:c534 Logitech, Inc. Unifying Receiver
- Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
- Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
- Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
- Bus 003 Device 013: ID 10d6:10d6 Actions Semiconductor Co., Ltd
- Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
+Flashing debian image +---------------------
+.. code-block:: none
- $ sudo ./ActionsFWU.py --fw=debian-stretch-desktop-cb7-emmc-v2.0.fw
- ActionsFWU.py : 1.0.150828.0830
- libScript.so : 2.3.150825.0951
- libFileSystem.so: 2.3.150825.0952
- libProduction.so: 2.3.150915.1527
- =====burn all partition====
- FW_VER: 3.10.37.180608
- 3% DOWNLOAD ADFUDEC ...
- 5% DOWNLOAD BOOT PARA ...
- 7% SWITCH ADFUDEC ...
- 12% DOWNLOAD BL31 ...
- 13% DOWNLOAD BL32 ...
- 15% DOWNLOAD VMLINUX ...
- 20% DOWNLOAD INITRD ...
- 24% DOWNLOAD FDT ...
- 27% DOWNLOAD ADFUS ...
- 30% SWITCH ADFUS ...
- 32% DOWNLOAD MBR ...
- 35% DOWNLOAD PARTITIONS ...
- WRITE_MBRC_PARTITION
- 35% write p0 size = 2048 : ok
- WRITE_BOOT_PARTITION
- 35% write p1 size = 2048 : ok
- WRITE_MISC_PARTITION
- 36% write p2 size = 98304 : ok
- WRITE_SYSTEM_PARTITION
- 94% write p3 size = 4608000 : ok
- FORMAT_SWAP_PARTITION
- 94% write p4 size = 20480 : ok
- 95% TRANSFER OVER ...
- Firmware upgrade successfully!
+Debian image can be downloaded from here[1].
+Once debian image is flashed, one can get into u-boot prompt by pressing any key and from +there run ums command(make sure, usb cable is connected between host and target):
+.. code-block:: none
- owl> ums 0 mmc 1
+Above command would mount debian image partition on host machine.
+Building U-BOOT proper image +----------------------------
+.. code-block:: none
- $ make clean
- $ export CROSS_COMPILE=aarch64-linux-gnu-
- $ make ARCH=arm cubieboard7_defconfig
- $ make u-boot-dtb.img -j16
+u-boot-dtb.img can now be flashed to debian image partition mounted on host machine.
+.. code-block:: none
- $ sudo dd if=u-boot-dtb.img of=/dev/sdb bs=1024 seek=3072
+[1]: https://pan.baidu.com/s/1uawPr0Jao2HgWFLZCLzHAg#list/path=%2FCubieBoard_Down... diff --git a/doc/board/actions/index.rst b/doc/board/actions/index.rst new file mode 100644 index 0000000..c596879 --- /dev/null +++ b/doc/board/actions/index.rst @@ -0,0 +1,10 @@ +.. SPDX-License-Identifier: GPL-2.0+ +.. Copyright (C) 2020 Amit Singh Tomar amittomer25@gmail.com
+Actions +========
+.. toctree::
- :maxdepth: 2
- cubieboard7
diff --git a/doc/board/index.rst b/doc/board/index.rst index 51a2ae6..01b233f 100644 --- a/doc/board/index.rst +++ b/doc/board/index.rst @@ -6,6 +6,7 @@ Board-specific doc .. toctree:: :maxdepth: 2
- actions/index AndesTech/index atmel/index coreboot/index
-- 2.7.4