From: Tang Yuantian Yuantian.Tang@freescale.com
Freescale ARM-based Layerscape LS102xA contain a SATA controller which comply with the serial ATA 3.0 specification and the AHCI 1.3 specification. This patch adds SATA feature on ls1021aqds and ls1021atwr boards.
Signed-off-by: Tang Yuantian Yuantian.Tang@freescale.com --- v2: - rebase to latest git tree - use micro SATA_ECC_REG_ADDR instead of hard coding
arch/arm/include/asm/arch-ls102xa/config.h | 15 ++++++ arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h | 24 +++++++++ board/freescale/ls1021aqds/ls1021aqds.c | 61 +++++++++++++++++++++++ board/freescale/ls1021atwr/ls1021atwr.c | 61 +++++++++++++++++++++++ 4 files changed, 161 insertions(+)
diff --git a/arch/arm/include/asm/arch-ls102xa/config.h b/arch/arm/include/asm/arch-ls102xa/config.h index c55cdef..a4a5d84 100644 --- a/arch/arm/include/asm/arch-ls102xa/config.h +++ b/arch/arm/include/asm/arch-ls102xa/config.h @@ -79,6 +79,21 @@ #define CONFIG_SYS_PCIE2_PHYS_ADDR (CONFIG_SYS_PCIE2_PHYS_BASE + \ CONFIG_SYS_PCIE2_VIRT_ADDR)
+/* SATA */ +#define AHCI_BASE_ADDR (CONFIG_SYS_IMMR + 0x02200000) +#define CONFIG_BOARD_LATE_INIT +#define CONFIG_CMD_SCSI +#define CONFIG_LIBATA +#define CONFIG_SCSI_AHCI +#define CONFIG_SCSI_AHCI_PLAT +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ + CONFIG_SYS_SCSI_MAX_LUN) +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#define CONFIG_SYS_FSL_ERRATUM_A008407 + #ifdef CONFIG_DDR_SPD #define CONFIG_SYS_FSL_DDR_BE #define CONFIG_VERY_BIG_RAM diff --git a/arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h b/arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h index d34044a..211fe1d 100644 --- a/arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h +++ b/arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h @@ -397,4 +397,28 @@ struct ccsr_cci400 { u8 res_e004[0x10000 - 0xe004]; };
+/* AHCI (sata) register map */ +struct ccsr_ahci { + u32 res1[0xa4/4]; /* 0x0 - 0xa4 */ + u32 pcfg; /* port config */ + u32 ppcfg; /* port phy1 config */ + u32 pp2c; /* port phy2 config */ + u32 pp3c; /* port phy3 config */ + u32 pp4c; /* port phy4 config */ + u32 pp5c; /* port phy5 config */ + u32 paxic; /* port AXI config */ + u32 axicc; /* AXI cache control */ + u32 axipc; /* AXI PROT control */ + u32 ptc; /* port Trans Config */ + u32 pts; /* port Trans Status */ + u32 plc; /* port link config */ + u32 plc1; /* port link config1 */ + u32 plc2; /* port link config2 */ + u32 pls; /* port link status */ + u32 pls1; /* port link status1 */ + u32 pcmdc; /* port CMD config */ + u32 ppcs; /* port phy control status */ + u32 pberr; /* port 0/1 BIST error */ + u32 cmds; /* port 0/1 CMD status error */ +}; #endif /* __ASM_ARCH_LS102XA_IMMAP_H_ */ diff --git a/board/freescale/ls1021aqds/ls1021aqds.c b/board/freescale/ls1021aqds/ls1021aqds.c index d6ef6ba..1b26ed3 100644 --- a/board/freescale/ls1021aqds/ls1021aqds.c +++ b/board/freescale/ls1021aqds/ls1021aqds.c @@ -18,6 +18,8 @@ #include <fsl_ifc.h> #include <fsl_sec.h> #include <spl.h> +#include <ahci.h> +#include <scsi.h>
#include "../common/sleep.h" #include "../common/qixis.h" @@ -54,6 +56,52 @@ enum { GE1_CLK125, };
+static void ls1021a_sata_init(void) +{ + struct ccsr_ahci __iomem *ccsr_ahci = (void *)AHCI_BASE_ADDR; + +#ifdef CONFIG_SYS_FSL_ERRATUM_A008407 +#define SATA_ECC_REG_ADDR 0x20220520 + unsigned int __iomem *ecc_reg = (void *)SATA_ECC_REG_ADDR; +#endif + + out_le32(&ccsr_ahci->ppcfg, 0xa003fffe); + out_le32(&ccsr_ahci->pp2c, 0x28183411); + out_le32(&ccsr_ahci->pp3c, 0x0e081004); + out_le32(&ccsr_ahci->pp4c, 0x00480811); + out_le32(&ccsr_ahci->pp5c, 0x192c96a4); + out_le32(&ccsr_ahci->ptc, 0x08000025); + +#ifdef CONFIG_SYS_FSL_ERRATUM_A008407 + out_le32(ecc_reg, 0x00020000); +#endif +} + +#ifdef CONFIG_SCSI_AHCI_PLAT +static int ls1021a_sata_start(void) +{ + struct ccsr_gur *gur = (struct ccsr_gur *)CONFIG_SYS_FSL_GUTS_ADDR; + u32 cfg; + int rc = -1; + + cfg = in_be32(&gur->rcwsr[4]) & RCWSR4_SRDS1_PRTCL_MASK; + cfg >>= RCWSR4_SRDS1_PRTCL_SHIFT; + + if (cfg != 0x30 && cfg != 0x70) { + printf("SATA disabled: serdes protocol doesn't support\n"); + return rc; + } + + rc = ahci_init((void __iomem *)AHCI_BASE_ADDR); + if (rc) + return rc; + + scsi_scan(0); + + return 0; +} +#endif + #ifdef CONFIG_LS102XA_NS_ACCESS static struct csu_ns_dev ns_dev[] = { { CSU_CSLX_PCIE2_IO, CSU_ALL_RW }, @@ -327,6 +375,8 @@ int board_early_init_f(void) fsl_dp_disable_console(); #endif
+ ls1021a_sata_init(); + return 0; }
@@ -388,6 +438,17 @@ void board_init_f(ulong dummy) } #endif
+#ifdef CONFIG_BOARD_LATE_INIT +int board_late_init(void) +{ +#ifdef CONFIG_SCSI_AHCI_PLAT + ls1021a_sata_start(); +#endif + + return 0; +} +#endif + void config_etseccm_source(int etsec_gtx_125_mux) { struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR; diff --git a/board/freescale/ls1021atwr/ls1021atwr.c b/board/freescale/ls1021atwr/ls1021atwr.c index b7458a9..6a964c3 100644 --- a/board/freescale/ls1021atwr/ls1021atwr.c +++ b/board/freescale/ls1021atwr/ls1021atwr.c @@ -22,6 +22,8 @@ #include <tsec.h> #include <fsl_sec.h> #include <spl.h> +#include <ahci.h> +#include <scsi.h> #include "../common/sleep.h" #ifdef CONFIG_U_QE #include "../../../drivers/qe/qe.h" @@ -173,6 +175,52 @@ struct cpld_data { u8 rev2; /* Reserved */ };
+static void ls1021a_sata_init(void) +{ + struct ccsr_ahci __iomem *ccsr_ahci = (void *)AHCI_BASE_ADDR; + +#ifdef CONFIG_SYS_FSL_ERRATUM_A008407 +#define SATA_ECC_REG_ADDR 0x20220520 + unsigned int __iomem *ecc_reg = (void *)SATA_ECC_REG_ADDR; +#endif + + out_le32(&ccsr_ahci->ppcfg, 0xa003fffe); + out_le32(&ccsr_ahci->pp2c, 0x28183411); + out_le32(&ccsr_ahci->pp3c, 0x0e081004); + out_le32(&ccsr_ahci->pp4c, 0x00480811); + out_le32(&ccsr_ahci->pp5c, 0x192c96a4); + out_le32(&ccsr_ahci->ptc, 0x08000025); + +#ifdef CONFIG_SYS_FSL_ERRATUM_A008407 + out_le32(ecc_reg, 0x00020000); +#endif +} + +#ifdef CONFIG_SCSI_AHCI_PLAT +static int ls1021a_sata_start(void) +{ + struct ccsr_gur *gur = (struct ccsr_gur *)CONFIG_SYS_FSL_GUTS_ADDR; + u32 cfg; + int rc = -1; + + cfg = in_be32(&gur->rcwsr[4]) & RCWSR4_SRDS1_PRTCL_MASK; + cfg >>= RCWSR4_SRDS1_PRTCL_SHIFT; + + if (cfg != 0x10 && cfg != 0x30 && cfg != 0x70) { + printf("SATA disabled: serdes protocol doesn't support\n"); + return rc; + } + + rc = ahci_init((void __iomem *)AHCI_BASE_ADDR); + if (rc) + return rc; + + scsi_scan(0); + + return 0; +} +#endif + #ifndef CONFIG_QSPI_BOOT static void convert_serdes_mux(int type, int need_reset);
@@ -522,9 +570,22 @@ int board_early_init_f(void) fsl_dp_disable_console(); #endif
+ ls1021a_sata_init(); + return 0; }
+#ifdef CONFIG_BOARD_LATE_INIT +int board_late_init(void) +{ +#ifdef CONFIG_SCSI_AHCI_PLAT + ls1021a_sata_start(); +#endif + + return 0; +} +#endif + #ifdef CONFIG_SPL_BUILD void board_init_f(ulong dummy) {