On 12/19/23 18:39, Alexander Dahl wrote:
Hello Eugen,
Am Tue, Dec 19, 2023 at 04:32:07PM +0200 schrieb Eugen Hristev:
On 12/12/23 18:04, Alexander Dahl wrote:
These removed definitions were specific to some sam9 SoCs, but not generic over all at91 SoCs. The correct SoC specific definitions for ATMEL_BASE_PMECC are spread over different header files in arch/arm/mach-at91/include/mach directory.
Fixes a build error on a custon board based on SAMA5D2:
Building current source for 73 boards (16 threads, 1 job per thread) arm: + vera2 +drivers/mtd/nand/raw/atmel/pmecc.c:819: warning: "ATMEL_BASE_PMECC" redefined + 819 | #define ATMEL_BASE_PMECC 0xffffe000 + | +In file included from include/configs/vera2.h:11, + from include/config.h:3, + from include/linux/mtd/rawnand.h:16, + from drivers/mtd/nand/raw/atmel/pmecc.c:44: +include/asm/arch/sama5d2.h:171: note: this is the location of the previous definition + 171 | #define ATMEL_BASE_PMECC (ATMEL_BASE_HSMC + 0x70) +drivers/mtd/nand/raw/atmel/pmecc.c:820: warning: "ATMEL_BASE_PMERRLOC" redefined + 820 | #define ATMEL_BASE_PMERRLOC 0xffffe600 +include/asm/arch/sama5d2.h:172: note: this is the location of the previous definition + 172 | #define ATMEL_BASE_PMERRLOC (ATMEL_BASE_HSMC + 0x500)Fixes: a490e1b7c017 ("nand: atmel: Add pmecc driver") Signed-off-by: Alexander Dahl ada@thorsis.com
drivers/mtd/nand/raw/atmel/pmecc.c | 3 --- 1 file changed, 3 deletions(-)
diff --git a/drivers/mtd/nand/raw/atmel/pmecc.c b/drivers/mtd/nand/raw/atmel/pmecc.c index e2e3f1ee6b5..51f6bd2e65b 100644 --- a/drivers/mtd/nand/raw/atmel/pmecc.c +++ b/drivers/mtd/nand/raw/atmel/pmecc.c @@ -816,9 +816,6 @@ int atmel_pmecc_wait_rdy(struct atmel_pmecc_user *user) } EXPORT_SYMBOL_GPL(atmel_pmecc_wait_rdy);
-#define ATMEL_BASE_PMECC 0xffffe000 -#define ATMEL_BASE_PMERRLOC 0xffffe600
static struct atmel_pmecc * atmel_pmecc_create(struct udevice *dev, const struct atmel_pmecc_caps *caps,
Hi Alexander,
What happens if we try to select and build this driver without sama5d2/sama5d3/sama5d4/sam9x5/sam9x60 ? Is it even possible ?
It is not possible on non-at91 boards because <mach/at91_sfr.h> is included so you need to select arch at91. But it is possible on older sam9 boards like sam9260, sam9g20 and the like. Tried that by using at91sam9g20ek_nandflash_defconfig as a base, then disabling CONFIG_NAND_ATMEL, then enabling CONFIG_DM_NAND_ATMEL (which activates build of drivers/mtd/nand/raw/atmel/pmecc.c), then enabling some more missing dependencies (CONFIG_MFD_ATMEL_SMC, CONFIG_REGMAP, CONFIG_SYSCON) and then it builds just fine.
(btw: should those be selected or implied by CONFIG_DM_NAND_ATMEL in 'drivers/mtd/nand/raw/Kconfig' then in another patch or is this stuff rather loose coupled?)
Hi Alexander,
I tried to look around the drivers and the symbols, but it appears enabling any sort of driver makes things stop building, as the dependencies are not at all stated correctly. Thus, I cannot really answer that. About this modification in particular, I ran the CI loop, it appears to be fine, and I agree with the duplication, I was a bit reluctant to not break old platforms, but since the CI says it's fine... I applied your set to u-boot-at91/master .
Eugen
Because it appears these defines are done for those SoCs in their mach header, but the driver uses them in any situation.
I don't think so. There are two drivers, the old one is 'drivers/mtd/nand/raw/atmel_nand.c' selected by CONFIG_NAND_ATMEL while the new one is 'drivers/mtd/nand/raw/atmel/nand-controller.c' selected by CONFIG_DM_NAND_ATMEL (note the extra sub-directory). Only the new one leads to building the file in question. The symbols removed from pmecc.c are not used in pmecc.c but only in the old driver. The scope of those removed symbols would have been in pmecc.c only however, they are pointless at the place where they are currently defined. (Unless someone would #include that .c file, but that seems rather unusual.)
And the part where the symbols of the same name are used is conditionally built only if CONFIG_ATMEL_NAND_HW_PMECC is set. From a quick glance I would say that one is set only for newer boards, those families you mentioned below. But as said, all this is for the old driver.
And currently, these warnings are being ignored if the driver is built with sama5d2/sama5d3/sama5d4/sam9x5/sam9x60 ?
The warning only popped up for a custom board build, where I include <asm/arch/sama5d2.h> in file 'include/configs/myboard.h' and keep some old definitions for the old driver and then switching from the old to the new driver. I did not see it for any mainline at91 defconfig. Nevertheless I consider those defines wrong in that place.
or the driver actually isn't even built with these platforms at all ?
It depends on the (def)config. Currently in mainline U-Boot to my knowledge the new driver is only used by sam9x60 and sam7g*something, but it was ported from Linux and it should support all at91 SoCs. I think it is just a matter of who migrates all those boards to the new driver?
So, I guess it would be safer to do #ifndef ATMEL_BASE_PMECC, #define ...
Or, we could fix the driver to get these base addresses from the platform/DT ?
As said above. The new driver does not these definitions at all, but already gets these addresses from DT. See sam9x60 curiosity for example.
Greets Alex